Sony DHC-AZ55D / HCD-AZ55D Service Manual ▷ View online
HCD-AZ55D
21
3-19. LEVER (LOADING-L/R)
two hooks
two hooks
BOTTOM VIEW
lever (loading-L)
lever (loading-R)
SPT-T (loading-R)
SPR-T (loading-L)
PRECAUTION DURING LEVER (LOADING R/L) INSTALLATION
lever (loading-R)
Align the horizontal position.
lever (loading-L)
Install the both levers so that they move symmetrically.
HCD-AZ55D
22
3-20. LEVER (DISC SENSOR)/(DISC STOP)
3-21. GEAR (IDL-C)
chassis (top)
hole
Install the lever (disc stop) so that the both holes
are aligned.
are aligned.
hole
gear (cap)
two claws
two hooks
lever (disc stop)
lever (disc stop)
lever (disc sensor)
PRECAUTION DURING DISC STOP LEVER INSTALLATION
gear (IDL L)
three hooks
two claws
claw
gear (IDL-F)
gear (IDL-C)
gear (IDL-D)
lever (gear loading) assy
HCD-AZ55D
23
SECTION 4
TEST MODE
COLD RESET
The cold reset clears data except DVD data stored in the RAM to
initial conditions. Execute this mode when returning the set to the
customers.
Procedure:
1. Press the [
The cold reset clears data except DVD data stored in the RAM to
initial conditions. Execute this mode when returning the set to the
customers.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of [
?
/
1
], [DISPLAY] and touch the [
x
] sen-
sor simultaneously.
3. The message “COLD RESET” is displayed on the fl uorescent
indicator tube, then become standby mode.
PANEL TEST MODE
This mode is used to check the fl uorescent indicator tube, LED,
model, destination, software version and key.
Procedure:
1. Press two buttons of [EQ EDIT], [DIRECTION] and touch the
This mode is used to check the fl uorescent indicator tube, LED,
model, destination, software version and key.
Procedure:
1. Press two buttons of [EQ EDIT], [DIRECTION] and touch the
[
x
] sensor simultaneously.
2. All LEDs and segments in fl uorescent indicator tube are light-
ed up.
3. When you want to enter the software version display mode,
touch the [
.
-] sensor. The model name is displayed.
4. Each time [
.
-] sensor is touched, the display changes from
destination, MC version, SYS version, UI version, DVD ver-
sion, ST version, TA version, DSP version, TM version, TC
version, MM version, CLA version in this order, and returns to
the model name display.
sion, ST version, TA version, DSP version, TM version, TC
version, MM version, CLA version in this order, and returns to
the model name display.
5. When [
>
+] sensor is touched while the version numbers
are being displayed except model name and destination, the
date of the software creation appear. When [
date of the software creation appear. When [
>
+] sensor
is touched again, the display returns to the software version
display. When [
display. When [
.
-] sensor is touched while the date of the
software creation is being displayed, the date of the software
creation is displayed in the same order of software version dis-
play.
creation is displayed in the same order of software version dis-
play.
6. Press the [DSGX] button, the key check mode is activated.
7. In the key check mode, the fl uorescent indicator tube displays
7. In the key check mode, the fl uorescent indicator tube displays
“K 0” Each time a button is pressed, “K 0” value increases.
However, once a button has been pressed, it is no longer taken
into account.
However, once a button has been pressed, it is no longer taken
into account.
8. To release from this mode, press three buttons in the same
manner as step 1 or disconnect the power cord.
SHIP MODE
This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the [
This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Touch the [DVD] sensor to select “DVD”
3. Press the [
3. Press the [
?
/
1
] button and touch [
bB
] sensor simultaneously.
4. After the “STANDBY” blinking display fi nish, the message
“MECHA LOCK” is displayed on the fl uorescent indicator
tube.
tube.
MEMORY CLEAR MODE
This mode moves clears main microprocessor data stored in the
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
This mode moves clears main microprocessor data stored in the
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Touch the [DVD] sensor to select the “DVD”
3. Press the [PRESET EQ] button and touch two sensors of
3. Press the [PRESET EQ] button and touch two sensors of
[DVD], [
x
] simultaneously.
4. After the “STANDBY” blinking display fi nish, the message
“MECHA LOCK” is displayed on the fl uorescent indicator
tube.
tube.
DISC SLOT LOCK
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when [
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when [
Z
] button is pressed. The message
“LOCKED” will be displayed in on the fl uorescent indicator tube.
Procedure:
1. Press the [
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Touch the [DVD] sensor to select the “DVD”
3. Touch the [
3. Touch the [
x
] sensor and press the [
Z
] button simultaneously
and hold down until “LOCKED” or “UNLOCKED” displayed
on the fl uorescent indicator tube (around 5 seconds).
on the fl uorescent indicator tube (around 5 seconds).
TUNER STEP CHANGE
(Except 220V – 230V AC area in E model)
The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press the [
(Except 220V – 230V AC area in E model)
The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Touch the [TUNER/BAND] sensor to select the “AM”
3. Press the [
3. Press the [
?
/
1
] button to turn the power off.
4. Touch the. [
.
-] sensor and press [
?
/
1
] button simultane-
ously. The set power on automatically. The message “AM 9k
Step” or “AM10k Step” displayed on the fl uorescent indicator
tube and thus the channel step is changed.
Step” or “AM10k Step” displayed on the fl uorescent indicator
tube and thus the channel step is changed.
FUNCTION NAME CHANGE
This mode let you change from VIDEO to SAT and vice-versa.
Procedure:
1. Press the [
This mode let you change from VIDEO to SAT and vice-versa.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Touch the [VIDEO/SAT] sensor and press [
?
/
1
] button simul-
taneously. The set power on automatically and the function
will changed to SAT. Do the same procedures again to change
from SAT to VIDEO.
will changed to SAT. Do the same procedures again to change
from SAT to VIDEO.
COLOR SYSTEM CHANGE
(Except 220V – 230V AC area in E model)
This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press the [
(Except 220V – 230V AC area in E model)
This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Touch the [DVD] sensor to select the “DVD”
3. Press the [
3. Press the [
?
/
1
] button to turn the power off.
4. Touch the [
X
] sensor and press [
?
/
1
] button simultaneously.
5. The message “COLOR PAL” or “COLOR NTSC” will be dis-
played on the fl uorescent indicator tube.
HCD-AZ55D
24
TEST DISC LIST
Use the following test disc on test mode.
YEDS-18 (CD)
Use the following test disc on test mode.
YEDS-18 (CD)
: PART No. 3-702-101-01
PATD-012 (CD)
: PART No. 4-225-203-01
HLX-503 (DVD-SL) (NTSC) : PART No. J-6090-069-A
HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A
HLX-506 (DVD-SL) (PAL)
HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A
HLX-506 (DVD-SL) (PAL)
: PART No. J-6090-077-A
HLX-501 (DVD-DL) (NTSC) : PART No. J-6090-071-A
HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A
HLX-507 (DVD-DL) (PAL) : PART No. J-6090-078-A
HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A
HLX-507 (DVD-DL) (PAL) : PART No. J-6090-078-A
Note: Do not use excepting test disc for DVD.
1. DVD SERVICE MODE GENERAL DESCRIPTION
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions, diag-
nostic results, etc. are given on the on-screen display.
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions, diag-
nostic results, etc. are given on the on-screen display.
2. ENTERING DVD SERVICE MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?
/
1
] button to turn on the system.
2. Touch the [DVD] sensor to select the “DVD”
3. Press the [
3. Press the [
Z
] button and touch two sensors of [
x
] and
[VOLUME +] simultaneously.
4. The message “SERVICE IN” appears on the fl uorescent in-
dicator tube and top menu of the Remocon Diagnosis Menu
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are dis-
played at the bottom of the on-screen display.
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are dis-
played at the bottom of the on-screen display.
Drive Manual Operation
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name
:ARX3DM_xx
IF-con:Ver.xx.xx(xxxx)
Syscon:Ver.x.xxx
Syscon:Ver.x.xxx
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press the [
?
/
1
] button to turn off the
system.
DVD SECTION
3. EXECUTING IOP MEASUREMENT
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2.
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2.
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the on-
screen display
remote commander. The following screen appears on the on-
screen display
Remocon Diagnosis Menu
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
on-screen display.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
V v Change Value
[RETURN]Return to previous menu
3. Select “6. Iop:” by pressing [6] button on the remote com-
mander.
4. Wait until a hexadecimal number appear in the on-screen dis-
play as below.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop: 5D
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop: 5D
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
V v Change Value
[RETURN]Return to previous menu
Click on the first or last page to see other DHC-AZ55D / HCD-AZ55D service manuals if exist.