Sony DAV-TZ150 Service Manual ▷ View online
DAV-TZ150
9
2-5. FRONT CABINET BLOCK
2 connector
(CN202)
(CN202)
3 connector
(CN203)
(CN203)
4 claw
1 Cut two wire ties.
5 seven claws
6 front cabinet block
wire tie
wire tie
tray
CONTROL board
MAIN board
POWER board
DVD mechanism deck
(CMS-LS5FP)
(CMS-LS5FP)
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
WireVHWWLQJ
Bring the slack part to the front side.
–5HDUULJKWYLHZ–
Note 2: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Note 1: In reassembling, use new wire tie
to fasten the clamp same as before.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
DAV-TZ150
10
2-6. STANDBY BOARD, CONTROL BOARD
7 USB grounding sheet
2 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
6 grounding spring sheet
6 grounding spring sheet
4 STANDBY board
0 CONTROL board
CONTROL board
shield wire for USB (WR1)
wire (WR2)
CONTROL board
STANDBY board
9 connector
(CN201)
(CN201)
3 two claws
1 two claws
8 two claws
WireVeWWiQJ
WireVeWWiQJ
–)rRQWFDEiQeWiQQerYieZ–
–)rRQWFDEiQeWiQQerYieZ–
–)rRQWFDEiQeWiQQerYieZ–
DAV-TZ150
11
2-7. DVD MECHANISM DECK BLOCK
2 connector
(CN301)
(See
(CN301)
(See
Fig.
A)
3 flexible cable
(CN300)
(CN300)
6 Remove the DVD
mechanism
mechanism
deck
block in the direction
of the arrow.
7 DVD mechanism deck
block
block
1 Cut two wire ties. (See Fig. A)
<Fig. A>
Note 1:
In reassembling, use new wire tie
to fasten the clamp same as before.
4 two screws
(BVTT3
(BVTT3
u 7)
4 two screws
(BVTT3
(BVTT3
u 7)
5 claw
5 claw
– Rear right view –
Wire setting
wire tie
wire tie
tray
CONTROL board
MAIN board
POWER board
DVD mechanism deck
(CMS-LS5FP)
(CMS-LS5FP)
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
Bring the slack part to the front side.
Note 4: When installing the flexible flat cable, ensure the colored line.
No slanting after insertion.
Note 3: When installing the flexible flat cable,
check that the terminal is not damaged.
Terminal is damaged.
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
OK
NG
Note 2: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
connector
flexible flat
cable
cable
connector
OK
NG
DAV-TZ150
12
2-8. DVD MECHANISM DECK (CMS-LS5FP)
1 Pass a short side of flexible cable
(FFC1) through the hole.
3 two claws
– DVD mechanism deck bottom view –
– DVD mechanism deck bottom view –
+RZWRLQVWDOOIOH[LEOHFDEOH))&
DVD mechanism deck
CMS-LS5FP)
CMS-LS5FP)
mechanism deck
4 flexible cable (FFC1)
5 DVD mechanism deck
(CMS-LS5FP)
(CMS-LS5FP)
4 Bend the flexible cable (FFC1).
2 Hang the flexible cable (FFC1)
on
on
claw.
3 Hang the flexible cable (FFC1)
on
on
claw.
2 connector
1 connector
Note 2: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
colored line
Insert is straight to the interior.
Insert is incline
colored line
flexible flat
cable
cable
connector
connector
flexible flat
cable
cable
OK
NG
Note 1: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Click on the first or last page to see other DAV-TZ150 service manuals if exist.