Sony DAV-TZ145 / HBD-TZ145 Service Manual ▷ View online
HBD-TZ145
9
2-5. FRONT CABINET BLOCK
2 connector
(CN202)
3 connector
(CN203)
4 claw
1 Cut two wire ties.
Note: In reassembling, use new wire tie
to fasten the clamp same as before.
5 seven claws
6 front cabinet block
wire tie
wire tie
tray
CONTROL board
MAIN board
POWER board
DVD mechanism deck
(CMS-S76RFS3G)
(CMS-S76RFS3G)
Bring the slack part to the front side.
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
WireVeWWiQJ
–5eDrriJKWYieZ–
HBD-TZ145
10
2-6. STANDBY BOARD, CONTROL BOARD
• Front cabinet inner view
6 USB grounding sheet
2 screw
(BVTP2.6)
5 screw
(BVTP2.6)
5 screw
(BVTP2.6)
5 screw
(BVTP2.6)
5 screw
(BVTP2.6)
4 STANDBY board
9 CONTROL board
CONTROL board
CONTROL board
STANDBY board
8 connector
(CN201)
3 two claws
1 two claws
claw
claw
7 two claws
WireVeWWiQJ
WireVeWWiQJ
HBD-TZ145
11
2-7. DVD MECHANISM DECK (F-8829F1)
Note 1: When disconnecting the fl exible cable of optical pick-up block, solder the short-land.
3 Solder the short-land.
2 connector
(CN301)
(See
(See
Fig.
A)
4 flexible cable
(CN300)
7 Remove the DVD mechanism
deck (F-8829F1) in the
direction of the arrow.
8 DVD mechanism deck
(F-8829F1)
1 Cut two wire ties. (See Fig. A)
<Fig. A>
Note 3: When assembling the optical
pick-up block, remove the solder
of short-land after connecting the
flexible
cable.
Note 2: In reassembling, use new wire tie
to fasten the clamp same as before.
5 two screws
(BVTT3
u 7)
5 two screws
(BVTT3
u 7)
6 claw
6 claw
– Rear right view –
Wire setting
wire tie
wire tie
tray
CONTROL board
MAIN board
POWER board
DVD mechanism deck
(F-8829F1)
(F-8829F1)
Bring the slack part to the front side.
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
HBD-TZ145
12
2-8. FFC HOLDER
1 claw
1 claw
1 Insert the flexible cable
to the FFC holder.
FFC holder
2 Hang the flexible cable on
two claws of the FFC holder.
5 two claws
3 flexible cable
6 flexible cable
4 FFC holder block
– DVD mechanism deck bottom view –
+ow to instaOO IOe[ibOe cabOe
7 FFC holder
3 Pass a short side of
flexible cable through
the hole of the FFC
holder.
4 Pass a long side of flexible cable
through the hole of the FFC holder.
2 Remove the FFC holder
block in the direction of
the
arrow.
Click on the first or last page to see other DAV-TZ145 / HBD-TZ145 service manuals if exist.