DOWNLOAD Sony DAV-SB300 / HCD-SB300 Service Manual ↓ Size: 8.76 MB | Pages: 106 in PDF or view online for FREE

Model
DAV-SB300 HCD-SB300
Pages
106
Size
8.76 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
dav-sb300-hcd-sb300.pdf
Date

Sony DAV-SB300 / HCD-SB300 Service Manual ▷ View online

5
HCD-SB300
SECTION  1
SERVICING  NOTES
NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD  FREE  MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
RELEASING  THE  DISC  TRAY  LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure :
Press two buttons of
A
and
x
simultaneously for five seconds.
The message “UNLOCKED” is displayed and the tray is unlocked.
Note:
When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the
I/
1
button.
NOTE  OF  REPLACING  THE  DMB07  BOARD
When replacing the DMB07 board, since the adjustment value is
not set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
Procedure:
1. Set the test mode. (See page 24)
2. Press the [2] key of the remote commander, and set the “DRIVE
MANUAL OPERATION”. (See page 28)
3. Press the [6] key of the remote commander, and set the “2-6,
Memory Check”. (See page 30)
4. Press the [CLEAR] key of the remote commander, and initialize
Memory.
MODEL  IDENTIFICATION
MODEL
PART No.
AEP, UK models
4-253-346-0[]
Russian model
4-253-346-1[]
Saudi Arabia model
4-253-346-2[]
Singapore model
4-253-346-3[]
Korean and Chinese models
4-253-346-4[]
Australian model
4-253-346-5[]
PART No.
– Back Panel –
6
HCD-SB300
DECISION  TO  PASS  OR  FAIL  OF  THE  OPTICAL
PICK-UP  BLOCK
Connection:
Procedure:
1. Connect an oscilloscope to test point 1  pin and 3  pin of
CN901 on the DMB07 board.
2. Turn the power on.
3. Put the disc (LUV-P01) (Part No.: 4-999-032-01) (CD) in to
playback.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
5. Put the disc (TDV-520CSO) (Part No.: J-2501-236-A) (DVD)
is to playback.
6. Perform confirmation in the same manner as step 4.
Note:
A clear RF signal waveform means that the shape “
◊” can be clearly
distinguished at the center of the waveform.
Checking Location:
DMB07 board
CN901 
1
 pin
CN901 
3
 pin
+
oscilloscope
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
CD: 1.05 
±
 0.2 Vp-p
DVD: 1.09 
±
 0.2 Vp-p
RF signal waveform
– DMB07 Board (Component Side) –
CN901
IC701
IC207
IC801
1
7
7
HCD-SB300
SECTION  2
GENERAL
This section is extracted from
instruction manual.
Front Panel
A "/(power)
Disc tray
C A (open/close)
D H (play)
E X (pause)
F x (stop)
G ./>, PRESET –/+
FUNCTION
VOLUME –/+
PHONES jack
Front panel display
STANDBY indicator
M
(remote sensor)
STANDBY
PHONES
VOLUME
PRESET
FUNCTION
Rear Panel
A
SPEAKER jacks
B
VIDEO AUDIO IN L/R jacks
C
COMPONENT VIDEO OUT jacks
(except AEP, UK models)
(AEP, UK models)
E
MONITOR OUT (VIDEO/S VIDEO) jacks 
(except AEP, UK models)
F
AM terminals
G
FM 75
 COAXIAL jack
H
SAT AUDIO IN L/R jacks
FRONT L
WOOFER
SURR L
CENTER
WOOFER
SPEAKER
MONITOR OUT
COMPONENT VIDEO OUT
FRONT R
SURR R
AUDIO IN
L
Y
P
B
/C
B
P
R
/C
R
VIDEO
S VIDEO  (DVD  ONLY)
R
AUDIO IN
L
R
VIDEO
SAT
COAXIAL
AM
FM
75
OUTPUT(TO TV)
EURO AV
D
EURO AV OUTPUT (TO TV) jack
8
HCD-SB300
Remote
A
SONY TV DIRECT
B
SLEEP
C
TUNER/BAND
D
MUTING
E
TUNER MENU
F
PLAY MODE
G
REPEAT
H
FM MODE
I
TV
J
AUDIO
K
ANGLE
L
SUBTITLE
M .
/
>
, PRESET –/+ 
N H
 PLAY
O X
 PAUSE
P
DVD TOP MENU/ALBUM–
Q C
/
X
/
x
/
c
/ENTER
R
DVD DISPLAY
S
TV CH +/–
T
TV VOL +/–
U
TV 
[
/
1
 (on/standby)
V "
/
1
 (standby)
W Z
 (open/close)
X
DSGX
Y
AUTO FORMAT DIRECT
Z
MODE
wj
NIGHT MODE
wk
FUNCTION
wl
Number buttons
e;
ENTER
ez
m
/
M
/
/
 SLOW, TUNING –/+
es
x
 STOP
ed
DISPLAY
ef
DVD MENU/ALBUM+
eg
VOLUME +/–
eh
O
 RETURN
ej
TV/VIDEO
ek
CLEAR
el
DIMMER
r;
DVD SETUP
1
2
3
4
5
8
0
6
7
10
9
Page of 106
Display

Click on the first or last page to see other DAV-SB300 / HCD-SB300 service manuals if exist.