Sony DAV-SB100 / DAV-SB200 / HCD-SB100 / HCD-SB200 Service Manual ▷ View online
5
HCD-SB100/SB200
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output several times.
that the S curve waveform is output several times.
Ver. 1.5
Attention when IC101 (system controller) exchanged.
When IC101 (system controller) is exchanged, discharged C107.
The method of discharging C107, 4 pin and 5 pin of PN105 are
shorted only at the moment.
The method of discharging C107, 4 pin and 5 pin of PN105 are
shorted only at the moment.
4
5
short
6
HCD-SB100/SB200
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
STANDBY
IR
-
PRESET
+
-
VOLUME
+
FUNCTION
PHONES
PAUSE (
X
)
Pause playback of a disc temporarily.
OPEN/CLOSE (
)
Opens or closes the disc tray.
Remote Sensor
Point the DVD receiver remote control here.
Point the DVD receiver remote control here.
Display window
Disc Tray
Insert a disc here.
Insert a disc here.
@
/
1
(POWER) indicator
Switches the DVD Receiver ON and OFF.
STOP (
x
.
>
)
Stops playback of a disc.
PLAY (
H
A
)
To play back a disc.
Forward SKIP (
)
DVD: Go to NEXT chapter/track.
RADIO: To select preset station you want.
Reverse SKIP (
)
DVD: Go to beginning of current chapter/track or to previous
chapter/track.
RADIO: To select preset station you want.
VOLUME Control
Press “+” to increase volume or press “-” to
decrease the volume.
STANDBY indicator
Lights red when the receiver
is in Standby mode (off).
Lights red when the receiver
is in Standby mode (off).
FUNCTION
To select the Receiver’s source.
(FM, AM, VIDEO, TV or
CD/DVD)
PHONES
To connect headphones.
Front Panel Controls
•
Abbreviation
AUS
AUS
: Australian model
CND
: Canadian model
EA
: Saudi Arabia model
EE
: East European model
RU
: Russian model
SP
: Singapore model
7
HCD-SB100/SB200
(SB100: AEP, UK, RU, EE models)
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
panel. Electrostatic discharge may cause permanent
damage to the unit.
AC Power Cord
Plug into the power source.
Plug into the power source.
SPEAKER CONNECTORS
Connect the six supplied speakers
to these terminals.
Connect the six supplied speakers
to these terminals.
FM ANTENNA CONNECTOR
Connect the FM antenna to this terminal.
AM LOOP ANTENNA CONNECTORS
Connect the AM Loop antenna to this terminal.
EURO AV OUTPUT (TO TV)
Connect to your TV set.
Connect to your TV set.
VIDEO (AUDIO IN L/R)
Connect the audio output of an external
source (VCR, LD player, etc).
Connect the audio output of an external
source (VCR, LD player, etc).
MONITOR OUT (VIDEO)
Connect to a TV with video input.
Connect to a TV with video input.
Rear Panel Connections
8
HCD-SB100/SB200
(SB100: US, CND, EA, SP, AUS models)
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
panel. Electrostatic discharge may cause permanent
damage to the unit.
AC Power Cord
Plug into the power source.
Plug into the power source.
SPEAKER CONNECTORS
Connect the six supplied
speakers to these terminals.
Connect the six supplied
speakers to these terminals.
FM ANTENNA CONNECTORS
Connect the FM antenna to this terminal.
AM LOOP ANTENNA CONNECTORS
Connect the AM Loop antenna to this terminal.
VIDEO (AUDIO IN L/R)
Connect the audio output of an external
source (VCR, LD player, etc).
Connect the audio output of an external
source (VCR, LD player, etc).
MONITOR OUT (VIDEO)
Connect to a TV with video input.
Connect to a TV with video input.
MONITOR S VIDEO OUT (DVD Only)
Connect to a S Video Input on TV.
FOR DVD VIEWING ONLY.
COMPONENT VIDEO OUT (Y P
B
/C
B
P
R
/C
R
)
Connect to a TV with Y P
B
/C
B
P
R
/C
R
inputs.
FOR DVD VIEWING ONLY.
Rear Panel Connections
Click on the first or last page to see other DAV-SB100 / DAV-SB200 / HCD-SB100 / HCD-SB200 service manuals if exist.