Sony DAV-S400 / HCD-S400 Service Manual ▷ View online
4
HCD-S400
HOW TO OPEN THE DISC TRAY WHEN POWER
SWITCH TURNS OFF
SWITCH TURNS OFF
When removing the disc tray, high torque is necessary to turn the
ejection cam on the bottom surface. Therefore, the screw thread is
easily damaged. To prevent this damage, turn it carefully.
ejection cam on the bottom surface. Therefore, the screw thread is
easily damaged. To prevent this damage, turn it carefully.
1
Turn the cam in the direction of the arrow.
2
Pull-out the disc tray.
Cam
Hole of chassis
• CLEANING THE OPTICAL PICK-UP
Note 1:
In cleaning the lens, do not apply an excessive force
As the optical pick-up is vulnerable, application of
excessive force could damage the lens holder.
excessive force could damage the lens holder.
Note 2:
In cleaning, do not use a cleaner other than exclusive
cleaning liquid. (KK-91 or isopropyl alcohol)
Note 3:
Wipe the obujective lens spirally from center toward
outside. (See Figure A)
(Figure A)
• DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
disc in the store is equipped.
Setting Procedure :
1.
1.
Press the A button or the H button of the main unit or 1
button on the remote commander to turn the set on.
button on the remote commander to turn the set on.
2.
Press two buttons of DISPLAY and . PREV
simultaneously for two seconds.
simultaneously for two seconds.
3.
The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1.
1.
Press two buttons of DISPLAY and . PREV
simultaneously for two seconds again.
simultaneously for two seconds again.
2.
The message “UNLOCKED” is displayed and the tray is
unlocked.
unlocked.
Note : When “LOCKED” is displayed, the tray lock is not released
by turning power on/off with the POWER button.
• MOVEMENT CONFIRMATION BY THE REMOTE
CONTROLLER OF OTHER MODELS
CONTROLLER OF OTHER MODELS
Signal code of the attached remote controller may vary in the
generation of CD/DVD player.
The signal code of FUNCTION, BAND, ST/MONO and
MEMORY is different with the remote controller for DAV-S400
and the remote controller for DAV-S550/S880/C770/C990.
Be careful when you confirm by the remote controller of the different
model.
generation of CD/DVD player.
The signal code of FUNCTION, BAND, ST/MONO and
MEMORY is different with the remote controller for DAV-S400
and the remote controller for DAV-S550/S880/C770/C990.
Be careful when you confirm by the remote controller of the different
model.
Ver 1.4
NOTES ON DVD BOARD EXCHANGE
If a DVD board is exchanged, “DRIVE AUTO ADJUSTMENT’’
may be unable to be performed. In this case, initialize a memory in
the following procedure.
1.
may be unable to be performed. In this case, initialize a memory in
the following procedure.
1.
Starting Test Mode (See page 11).
2.
Press the 2 button of remote commander to set the Drive
Manual Operation (See page 16).
Manual Operation (See page 16).
3.
Press the 6 button of remote commander to set the Memory
Check (See page 18).
Check (See page 18).
4.
Press the [CLEAR] button of remote commander to initialize a
memory.
memory.
5
HCD-S400
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front Panel
POWER switch/indicator (30)
Disc tray (30)
OPEN/CLOSE (30)
Front panel display (10)
./>, PREV/NEXT, PRESET +/–
(28, 31)
H (play) (30)
X (pause) (31)
X (pause) (31)
PHONES jack (30)
VOLUME control (30)
SOUND FIELD +/– (46)
DISPLAY (46, 59)
BAND (28)
FUNCTION (58)
VOLUME control (30)
SOUND FIELD +/– (46)
DISPLAY (46, 59)
BAND (28)
FUNCTION (58)
(remote sensor) (16)
A
x (stop) (30)
AM antenna (19)
AUDIO 1 jacks (21)
AUDIO 2 jacks (21)
DIGITAL IN (OPTICAL) jack (22)
AUDIO 1 jacks (21)
AUDIO 2 jacks (21)
DIGITAL IN (OPTICAL) jack (22)
MONITOR OUT jack (21)
SPEAKER jacks (17)
FM 75 COAXIAL antenna jack (20)
SPEAKER jacks (17)
FM 75 COAXIAL antenna jack (20)
Rear Panel
AM
COAXIAL
FM
75
L
R
L
R
OPTICAL
DIGITAL IN
VIDEO OUT
AUDIO OUT AUDIO IN
AUDIO IN
SPEAKER
FRONT R
REAR R
CENTER
WOOFER
FRONT L
REAR L
IMPEDANCE USE WOOFER: 3 EXCEPT WOOFER: 6
A
N
T
E
N
N
A
N
T
E
N
N
A
AUDIO 1
AUDIO 2
MONITOR
OUT
Ω
6
HCD-S400
This section is extracted
from instruction manual.
from instruction manual.
Remote
1
2
3
4
5
6
7
>10
10/0
8
9
TV 1/= (on/standby) (57)
NAME (60)
STEREO/MONO (59)
STEREO/MONO (59)
MEMORY (28)
CLEAR (35)
CLEAR (35)
PLAY MODE (34)
AUDIO (44)
ANGLE (49)
SUBTITLE (50)
VOL +/– (58)
AUDIO (44)
ANGLE (49)
SUBTITLE (50)
VOL +/– (58)
./>, PREV/NEXT, TV CH +/–,
PRESET +/– (28, 31)
DVD TOP MENU (32)
DVD DISPLAY (37)
DVD DISPLAY (37)
T/R/r/t/ENTER (24)
DVD SETUP (54)
1 (standby) (30)
DIMMER (27)
TV/VIDEO (57)
REPEAT (37)
MUTING (31)
TIME (41)
FUNCTION (58)
TV/VIDEO (57)
REPEAT (37)
MUTING (31)
TIME (41)
FUNCTION (58)
BAND (28)
Number buttons (32)
SOUND FIELD (46)
DISPLAY (46, 59)
ENTER (57)
COMMAND MODE DVD/TV switch
(57)
Number buttons (32)
SOUND FIELD (46)
DISPLAY (46, 59)
ENTER (57)
COMMAND MODE DVD/TV switch
(57)
/
(28, 38)
STOP (30)
PAUSE (31)
PAUSE (31)
DVD MENU (33)
RETURN (34)
AMP MENU (24)
Z OPEN/CLOSE (30)
H PLAY/SELECT (30)
./>,
SLOW, TUNING +/–
O
x
X
7
HCD-S400
SECTION 3
DISASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
3-1. CASE (TOP), DVD LID, LID WINDOW SUB ASSEMBLY
3-2. FRONT PANEL SECTION
2
Two case screws
1
Two case
screws
Cam
Hole of chassis
5
Turn the cam in the direction of the arrow.
7
Two claws
8
DVD lid,
Lid window sub assembly
6
Pull-out the disc tray.
4
Case (Top)
3
Four screws
(+BVTP 3
×
8)
1
Connector (CN309)
3
Connector (CN902)
2
Flexible flat cable (15 core)
(CN005)
5
Two claws
4
Four screws
(+BVTP 3
×
8)
6
Front panel section
RF-240 board
Tray
Tray
Optical pick-up (KHM-240 AAA)
Front panel section
Case (Top)
Set
Loading board, Motor (LD) assy (M901)
DVD mechanism deck (CDM55C-DVBU8)
•
The equipment can be removed using the following procedure.