DOWNLOAD Sony DAV-LF1H / HCD-LF1H Service Manual ↓ Size: 7.53 MB | Pages: 79 in PDF or view online for FREE

21

q;

two screws 
(+BVTP 3 

×

 8) 

qa

two screws 
(+BVTP 3 

×

 6) 

qs

connector 
5P (CN601) 

5

connector 
8P (CN301) 

1

connector 
6P (CN101) 

3

connector 
2P (CN603) 

2

connector 
10P (CN602) 

4

connector 
7P (CN502) 

qf

connector 
5P (CN102) 

qg

saranet 
cushion

two saranet cushions

CN102

7

saranet cushion

qh

MAIN board

MAIN board
(side B)

qd

saranet cushion

harness

9

FFC 19p (40)
19core (CN302) 

8

FFC 7p (100)
7core (CN308)

6

cable (system)

Route the harnesses as shown below.

22

3

connector 
5P (CN601) 

5

DMB14 board 

2

six screws 
(+BVTP 3 

×

 6) 

1

FFC 19p (40)
19core (CN109)

4

FFC 50p (160)
50core (CN101)

23

Regarding the notification symbol “R”
Because the number of the operating buttons of this product
are limited, some operations require use of the operating
buttons of the remote commander, When a specific operation
requires use of the operating buttons of the remote
commander, “R” is added to the specific operating procedure
in this manual. Example  MENU/NO  “R”  The  MENU/NO
button of remote commander.

Incorrect operations may be performed if the test mode is
not entered properly.
In this case, press the  ?/1  button to turn the power off, and
retry to enter the test mode.

The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :

1. Press the  ?/1  button to turn the set on.
2. Press the  FUNCTION  button to set DVD function.
3. Insert a disc.
4. Press the  

x  

button and the  A  button simultaneously for five

seconds.

5. The message “LOCKED” is displayed and the slot is locked.

1. Press the  

x  

button and the  A  button simultaneously for five

seconds, again.

2. The message “UNLOCKED” is displayed and the slot is

unlocked.

When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the  ?/1  button.

•

Use this mode when returning the set to the customer after
repair.

1. Press the  ?/1  button to turn the set on.
2. Press the  FUNCTION  button to set the function “DVD”.
3. After all discs are removed, press two buttons   x  ,  A  ,  and

?/1  simultaneously.

4. After a message “MECHA LOCK” is displayed on the

fluorescent indicator tube, pull out the AC plug.

5. To exit from this mode, press the  ?/1  button to turn the set on.

•

A step of AM channels can be changed over between 9 kHz
and 10 kHz.

1. Press the  ?/1  button to turn the set on.
2. Select the function “TUNER”, and press  FUNCTION  button

to select the BAND “AM”.

3. Press the  ?/1  button to turn the set off.
4. Press two buttons  FUNCTION  and  ?/1  simultaneously,

and the display of fluorescent indicator tube changes to “AM
9 k STEP” or “AM 10 k STEP”, and thus the channel step is
changed over.

1. Press the  ?/1  button to turn the power on.
2. Press three buttons  x ,  N  and  A  simultaneously.
3. The message “Volume Max” is displayed, when press the

VOLUME +  button.
The message “Volume Min” is displayed, when press the
VOLUME –  button.

4. To exit from this mode, press the  ?/1  button to turn the set off.

This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the RAM
to initial conditions. Use this mode when returning the set to the
customer after repair.
Procedure:

1. Press the  ?/1  button to turn the power on.
2. Press the  FUNCTION  button to set the function “DVD”.
3. After all discs are removed, press three buttons  VOLUME –  ,

A  and  ?/1  simultaneously.

4. After the “STANDBY” blinking display finishes, the message

“MECHA LOCK” is displayed on the fluorescent indicator
tube and the ship mode is set.

5. After a message “MECHA LOCK” is displayed on the

fluorescent indicator tube, pull out the AC plug.

•

The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.

1. Press the  ?/1  button to turn the power on.
2. Press three buttons  x  ,   FUNCTION  and   ?/1  simulta-

neously.

3. When this button is operated, display as “COLD RESET” for

a while and all of the settings are reset.

•

This mode is used to check the software version, FL, LED
and KEY.

1. Press the  ?/1  button to turn the power on.
2. Press three buttons  x ,  VOLUME –  and  A  simultaneously.
3. When the display test mode is activated, all segments and all

LEDs are turned on.

4. To exit from this mode, press three buttons  x ,  VOLUME –

and  A  simultaneously.

1. When the panel test mode is activated, press the  VOLUME +

button and the message “LFZ5” is displayed, the version test
mode is activated.

2. Whenever the  VOLUME +  button is pressed, the display

changes in the following order.

*1: LAT changes depending on destination.

3. Press the  VOLUME –  button and the date of the software

production is displayed.

4. Press the  VOLUME –  button again and the version is

displayed.

5. To exit from this mode, press three buttons  x ,  VOLUME –

and  A  simultaneously.

1. When the panel test mode is activated, press the  N  button,

to select the key test mode.

2. To enter the KEY test mode, the fluorescent indicator displays

“K0”. Each time a button is pressed, “KEY” value increases.
However, once a button is pressed, it is no longer taken into
account. When all keys are pressed correctly, “K7” is displayed.

3. To exit from this mode, press three buttons  x ,  VOLUME –

and  A  simultaneously.

“LFZ5” (Model name) t “LAT

*1

” (Destination) t MC t SYS 

 

TM T DSP T TA T ST T CDMB T CDMA T DVD T UI

XM

24

Be sure to use the DVD disc that matches the signal standards of
your region.

HLX-513 (Part No.: J-2501-305-A)
HLX-A1

(Part No.: J-2501-307-A)

The Mirror Time allows you to make diagnosis and adjustment
simply by using the remote commander and monitor TV. The
instructions, diagnosis results, etc. are given on the on-screen display
(OSD).
Be sure to execute the Mirror time when a BU (Base Unit) is
replaced.

Press three buttons  

x  

,  A and  VOLUME +  simultaneously with

the DVD player.
The Test Mode starts, then the menu shown below will be displayed
on the TV screen.

The menu above is the Remocon Diagnosis Menu screen which
consists of five main functions. At the bottom of the menu screen,
the model name and IF-con version. To enter Mirror Time
Adjustment menu, press button  2 “R”  on the remote commander
to enter Drive Manual Operation menu. To exit from the Test Mode,
press the power button on the remote commander.

The Drive Manual Operation menu consists of five main functions.
By pressing  2 “R”  button on the remote commander in the Remocon
Diagnosis Menu, the screen will appear as shown.

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information

Model Name : LFZ5_ XX
IF-con

: V

Syscon

: Ver.

er. XX.XX (XXXX)

X.XXX

*

1

*1: Changes depending on destination 

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu

1. Press the  ?/1  button to turn on the system.
2. Press the  FUNCTION  button repeatedly unit “DVD” is

selected.

3. Press the  

x

  and  H  buttons simultaneously (around five

seconds) until “DEMO OFF” is displayed on the fluorescent
indicator tube.

4. When “DEMO OFF” is displayed, the DEMO disc playback

lock is released.