Sony DAV-HDX678WF / DAV-HDX975WF / HCD-HDX678WF / HCD-HDX975WF Service Manual ▷ View online
HCD-HDX678WF/HDX975WF
21
3-20. GEAR (BU1)
screw
(PWH2.6
(PWH2.6
× 8)
screw
(PWH2.6
(PWH2.6
× 8)
screw
(PWH2.6
(PWH2.6
× 8)
pulley (BU)
gear (BU1)
gear (BU2)
belt (sub tray)
gear (BU2)
cam (BU)
PRECAUTION DURING GEAR (BU2) INSTALLATION
Before re-assembling, slide the cam (BU) in the direction of
the arrow.
Assemble the gear (BU2) in such a manner that the groove
of the cam (BU) is aligned with the rib of the gear (BU2).
rib
groove
– CD mechanism deck bottom view –
HCD-HDX678WF/HDX975WF
22
SECTION 4
TEST MODE
Note: Incorrect operations may be performed if the test mode is not
entered properly. In this case, press the [?/1] button to turn the
power off, and retry to enter the test mode.
power off, and retry to enter the test mode.
COLD RESET
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customers.
Procedure:
1. Press the [
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customers.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Press three buttons [
s
], [
A
] and [
?
/
1
] simultaneously.
3. When this button is operated, display as “COLD RESET” for
a while and all of the settings are reset.
PANEL TEST MODE
This mode is used to check the software version, FL, LED and
KEY.
1. Display Test Mode
Procedure:
1. Press the [
This mode is used to check the software version, FL, LED and
KEY.
1. Display Test Mode
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Press three buttons [
S
], [
l
] and [
A
] simultaneously.
3. When the display test mode is activated, all segments are
turned on.
4. To exit from this mode, press three buttons [
S
], [
l
] and [
A
]
simultaneously.
2. Version Test Mode
Procedure:
1. When the display test mode is activated, press the [
Procedure:
1. When the display test mode is activated, press the [
l
] but-
ton and “DCR5WF” is displayed, the version test mode is acti-
vated.
vated.
2. Whenever the [
l
] button is pressed, the display changes in
order of “DCR5WF” (model name) → “NA” (destination) →
MC → SYS → UI → DVD → CDMA → CDMB → ST →
TA → DSP → TM → CLA → CEC → SAIR → “DCR5WF”
(model name).
MC → SYS → UI → DVD → CDMA → CDMB → ST →
TA → DSP → TM → CLA → CEC → SAIR → “DCR5WF”
(model name).
Note: Model name/destination is different according to model.
3. Press the [
L
] button and the date of the software production
is displayed.
4. Press the [
L
] button again and the version is displayed.
5. To exit from this mode, press three buttons [
S
], [
l
] and [
A
]
simultaneously.
3. Key Test Mode
Procedure:
1. When the display test mode is activated, press the [
Procedure:
1. When the display test mode is activated, press the [
H
] button,
to select the key test mode.
2. To enter the KEY test mode, the fl uorescent indicator displays
“K0 V0”. Each time an another button is pressed, “KEY” value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K13
V0” is displayed.
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K13
V0” is displayed.
3. When the [VOLUME] dial is turned in the direction of (+),
“V0” is changed to “V1”, then ... “V9”.
When the [VOLUME] dial is turned in the direction of (–),
“V0” is changed to “V9”, then ... “V1”.
“V0” is changed to “V9”, then ... “V1”.
4. To exit from this mode, press three buttons [
S
], [
l
] and [
A
]
simultaneously.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Press the [
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Press the [
?
/
1
] button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the [
3. Insert a disc.
4. Press the [
s
] button and the [
A
] button simultaneously for fi ve
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure:
1. Press the [
Releasing Procedure:
1. Press the [
s
] button and the [
A
] button simultaneously for fi ve
seconds again.
2. The message “UNLOCKED” is displayed and the tray is un-
locked.
Note: When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the [?/1] button.
DVD SHIP MODE
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
?
/
1
] button to turn the set on.
2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press two buttons [
3. Remove all discs, and then press two buttons [
H
] and [
?
/
1
]
simultaneously.
4. After a message “MECHA LOCK”
h “UNPLAG” is dis-
played on the fl uorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the [
?
/
1
] button to turn the set
on.
AM STEP CHANGE
A step of AM channels can be changed over between 9 kHz and
10 kHz.
Procedure:
1. Press the [
A step of AM channels can be changed over between 9 kHz and
10 kHz.
Procedure:
1. Press the [
?
/
1
] button to turn the set ON.
2. Press the [FUNCTION] button to set the function “TUNER
AM”.
3. Press the [
?
/
1
] button to turn the set OFF.
4. Press two buttons [
L
] and [
?
/
1
] simultaneously, and the dis-
play of fl uorescent indicator tube changes to “AM 9k STEP” or
“AM 10k STEP”, and thus the channel step is changed over.
“AM 10k STEP”, and thus the channel step is changed over.
PRODUCT OUT
This mode moves the optical pick-up to the position durable to vi-
bration and clears all data including preset data stored in the RAM
to initial conditions. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Press the [
This mode moves the optical pick-up to the position durable to vi-
bration and clears all data including preset data stored in the RAM
to initial conditions. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press three buttons [
3. Remove all discs, and then press three buttons [
L
], [
A
] and
[
?
/
1
] simultaneously.
4. After the “STANDBY” blinking display fi nishes, the message
“MECHA LOCK”
h “UNPLAG” is displayed on the fl uo-
rescent indicator tube disconnect the AC power plug, then the
ship mode is set.
ship mode is set.
AUTOMATIC ACOUSTIC FIELD CALIBRATION MICRO-
PHONE TEST MODE
Procedure:
1. Press the [
PHONE TEST MODE
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Insert ECM-AC2 supplied as an accessory into the AUDIO IN/
A.CAL MIC jack.
3. While pressing the [
S
] and [
A
] buttons simultaneously, turn
the [VOLUME] dial in the direction of (+).
4. The state of jack is displayed in the fl uorescent indicator tube.
NON: Not detected
ST:
STEREO
MN:
MONO
5. To exit from this mode, press two buttons [
S
] and [
A
] simul-
taneously, turn the [VOLUME] dial in the direction of (+)
Ver. 1.1
HCD-HDX678WF/HDX975WF
23
DEMO PLAY OUT
It is a mode to release the demonstration reproduct by the dedi-
cated demonstration disc.
Procedure:
1. During playback the DEMO disc, press the [
It is a mode to release the demonstration reproduct by the dedi-
cated demonstration disc.
Procedure:
1. During playback the DEMO disc, press the [
s
] and [
H
] but-
tons for fi ve seconds simultaneously.
2. The message “DEMO OFF” is displayed, a mode to reproduct
the demonstration is released.
AMP TEST MODE
1. Mode In, Mode Out
Procedure:
1. Press the [
1. Mode In, Mode Out
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Press three buttons [
l
], [
H
] and [
L
] simultaneously.
3. The message “MEASURE” is displayed.
4. To exit from this mode, press the [
4. To exit from this mode, press the [
?
/
1
] button to turn the set
off, the message “COLD RESET” is displayed.
2. Volume
Test
Procedure:
1. When the [VOLUME] control is turned in the direction of (+),
1. When the [VOLUME] control is turned in the direction of (+),
the message “VOLUME MAX” is displayed.
2. When the [VOLUME] control is turned in the direction of (–),
the message “VOLUME MIN” is displayed
3. Press the [MUTING] button on the remote commander.
4. The message “VOL N” is displayed and [VOLUME] control is
4. The message “VOL N” is displayed and [VOLUME] control is
normal.
5. Press the [MUTING] button on the remote commander again.
6. The message “VOL M/N” is displayed and [VOLUME] con-
6. The message “VOL M/N” is displayed and [VOLUME] con-
trol is “MAX” and “MIN”.
3. Measure/Safety
Procedure:
1. Press the [DISPLAY] button on the remote commander.
2. The message “SAFETY” is displayed.
3. Press the [DISPLAY] button on the remote commander again.
4. The message “MEASURE” is displayed.
Procedure:
1. Press the [DISPLAY] button on the remote commander.
2. The message “SAFETY” is displayed.
3. Press the [DISPLAY] button on the remote commander again.
4. The message “MEASURE” is displayed.
4. SWAP
Mode
Procedure:
1. Press the [SOUND MODE] button on the remote commander.
2. The message “SWAP FULL” is displayed.
3. Whenever the [SOUND MODE] button is pressed, the display
1. Press the [SOUND MODE] button on the remote commander.
2. The message “SWAP FULL” is displayed.
3. Whenever the [SOUND MODE] button is pressed, the display
changes in the following order.
“SWAP FULL” → “SWAP THRU” → “SWAP F2S” → “SWAP F2CW”
5. DCAC MIC Input Mode
Procedure:
1. Press the [D.BASS] button on the remote commander.
2. The message “D.C.A.C. MIC” is displayed.
3. Press the [D.BASS] button on the remote commander.
4. The message “FUNC INPUT” is displayed.
Procedure:
1. Press the [D.BASS] button on the remote commander.
2. The message “D.C.A.C. MIC” is displayed.
3. Press the [D.BASS] button on the remote commander.
4. The message “FUNC INPUT” is displayed.
Note: The segments of the frame of “CAT” and “SA-CD” are blinking
while test mode.
PROTECTION FACTOR (SD DETECTION/DC DETEC-
TION) IDENTIFICATION TEST MODE
When an error is detected, the fl orescent indicator tube alternately
displays
“PROTECTOR”
TION) IDENTIFICATION TEST MODE
When an error is detected, the fl orescent indicator tube alternately
displays
“PROTECTOR”
h “PUSH POWER”.
Press
the
[
?
/
1
] button.
* Buttons other than the [
?
/
1
] button are invalid.
“STANDBY” blinks three times on the fl orescent indicator tube.
The protection release state (POWER OFF) is established.
(No fl orescent indicator tube display)
Press
(No fl orescent indicator tube display)
Press
the
[
?
/
1
] button twice.
The power to the system turns on, and the normal operation is es-
tablished. (Restore)
tablished. (Restore)
During the protection state:
1. If the AC plug is connected or disconnected during the protec-
1. If the AC plug is connected or disconnected during the protec-
tion state, the protection state is released, and the normal op-
eration is established. (The protection state is not maintained)
eration is established. (The protection state is not maintained)
2. The protection factor is displayed by pressing the [FUNC-
TION], [
A
] and [
L
] buttons at the same time during the
protection state. (during the “PROTECTOR”
h “PUSH
POWER” display)
When SD is detected: Repeats
“SD
“SD
DETECT”
h “PROTECTOR”.
When DC is detected: Repeats
“DC
“DC
DETECT”
h “PROTECTOR”.
SD detection:
When the “L” output from the SD (shutdown) port on the
S-MASTER POWER Driver Shutdown and voltage descent
(15V or less) of 30V power supply (PVDD) are detected.
S-MASTER POWER Driver Shutdown and voltage descent
(15V or less) of 30V power supply (PVDD) are detected.
DC detection:
When the “L” output from the power/speaker error detection
circuit (DC detection port) is detected for two seconds continu-
ally, the power system other than that of the fl orescent indica-
tor tube is turned off, and the protection state is established.
circuit (DC detection port) is detected for two seconds continu-
ally, the power system other than that of the fl orescent indica-
tor tube is turned off, and the protection state is established.
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT CHECK JIG (Part No.: J-2501-309-A)
Procedure:
1. Connect the DMPORT CHECK JIG (Part No.: J-2501-309-A)
with the terminal DMPORT.
2. Press the [
?
/
1
] button to turn the power on.
3. Confi rm that both LEDs of the DMPORT confi rmation JIG
lights. (Confi rmation the power supply line.)
4. Set the [FUNCTION] button with “DMPORT” on this model.
5. Press the [
5. Press the [
S
], [
l
] buttons and turn the [VOLUME] control
in the direction of (+) simultaneously, the DMPORT test mode
is activated.
is activated.
6. It
is
confi rmed that “DMPORT OK” is displayed on this set
display. (Confi rmation of communication line)
7. To a pinjack of the DMPORT confi rmation JIG input informa-
tion relevant to audio signal (sine-wave 1.0Vrms) and compos-
ite video signal (white 100% 1.0 Vp-p, color bar, etc.)
ite video signal (white 100% 1.0 Vp-p, color bar, etc.)
8. Confi rm the output of speakers and monitor TV. (Confi rmation
of analog signal)
Ver. 1.1
HCD-HDX678WF/HDX975WF
24
1. DVD SERVICE MODE GENERAL DESCRIPTION
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions, diag-
nostic results, etc. are given on the on-screen display.
Be sure to execute the IOP measurement when a base unit is re-
placed.
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions, diag-
nostic results, etc. are given on the on-screen display.
Be sure to execute the IOP measurement when a base unit is re-
placed.
2. ENTERING DVD SERVICE MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?
/
1
] button to turn on the system.
2. Press the [FUNCTION] button repeatedly to select the
“DVD”.
3. While pressing the [
s
] and [
A
] buttons simultaneously, turn
[VOLUME] dial in the direction of (+) with the DVD player in
power on.
power on.
4. The message “SERVICE IN” appears on the fl uorescent in-
dicator tube and top menu of the Remocon Diagnosis Menu
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are dis-
played at the bottom of the on-screen display.
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are dis-
played at the bottom of the on-screen display.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name
:xxxx_xx
IF-con:Ver.xx.xx(xxxx)
Syscon:Ver.x.xxx
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press the [
?
/
1
] button to turn off the
system.
DVD SECTION
9. To exit from this mode, press the [
S
], [
l
] buttons and turn
the [VOLUME] control in the direction of (+).
color pattern
generator
DMPORT
check jig
(Part No.:
J-2501-309-A)
J001
AF oscillator
set
TV
monitor
FL/FR
speaker
MAIN board
CN204
SPEAKER board
TB101
IO board
J402
3. EXECUTING IOP MEASUREMENT
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the on-
screen display
remote commander. The following screen appears on the on-
screen display
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
on-screen display.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[
V][v] Change Value
[RETURN]Return to previous menu
3. Select “6. Iop:” by pressing [6] button on the remote com-
mander.
4. Wait until a hexadecimal number appear in the on-screen dis-
play as below.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq boost Adjust:
6. Iop: ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[
V][v] Change Value
[RETURN]Return to previous menu
5. Convert data from hexadecimal to decimal by using conver-
sion table.
6. If the value is smaller than 93 (decimal), then it is OK. How-
ever if the value is higher than 93, then BU (base unit) is defec-
tive and need to be change.
tive and need to be change.
7. Press the [
O
RETURN] button on the remote commander to
return to previous menu.
Ver. 1.1
Click on the first or last page to see other DAV-HDX678WF / DAV-HDX975WF / HCD-HDX678WF / HCD-HDX975WF service manuals if exist.