Sony DAV-HDX285 / DAV-HDX287WC / DAV-HDX585 / DAV-HDX587WC / DAV-HDX589W / DAV-HDX685 / DAV-HDX686W / HCD-HDX285 / HCD-HDX287WC / HCD-HDX585 / HCD-HDX587WC / HCD-HDX685 / HCD-HDX686W Service Manual ▷ View online
HCD-HDX285/HDX287WC/HDX585/HDX587WC/HDX589W/HDX685/HDX686W
13
3-4. S-AIR INCLUDE BOARD (HDX287WC/HDX587WC/HDX589W/HDX686W)
3-5. FRONT PANEL BLOCK
two screws
(BV3
(3-CR))
screw
(BV3
(3-CR))
two screws
(BV3
(3-CR))
wire (flat type) (13 core)
(S-AIR INCLUDE board: CN804,
MAIN board: CN306)
connector
(CN908)
bracket
(S-AIR INC board)
card slot
(S-AIR2)
four screws
(BV3
(3-CR))
R S-AIR INCLUDE board
connector
(CN801)
Turn gear (BU1) from a hole
at the bottom, and pull out a tray.
Open the tray.
gear (BU1)
RT claw
RT claw
RE front panel block
RB four screws
(BV3
(3-CR))
loading panel (DCY)
wire (flat type) (17 core)
(CN506)
connector
(CN3001)
R
connector
(CN4014)
two claws
– bottom view –
HCD-HDX285/HDX287WC/HDX585/HDX587WC/HDX589W/HDX685/HDX686W
14
3-6. COVER
(CDM-DCY)
3-7. DVD MECHANISM DECK BLOCK
four screws
(BV3
(3-CR))
cover
(CDM-DCY)
three screws
(BVTP3
× 10)
Turn over the DVD mechanism deck block.
DVD mechanism deck block
Please place a sheet for insulation.
wire (flat type) (24 core)
CN101
Note: Don’t remove the wire (flat type) (24 core) (CN101).
If you remove the wire (flat type) (24 core) (CN101),
solder the bridge of optical pick-up.
HCD-HDX285/HDX287WC/HDX585/HDX587WC/HDX589W/HDX685/HDX686W
15
3-8. DVD MECHANISM DECK (CDM81C-DVBU101)
wire (flat type) (24 core)
sheet for insulation
optical pick-up block
PRECAUTION WHEN REMOVING GOOD OPTICAL PICK-UP
four screws
(BTP2.6
× 8)
two insulator screws
R connector
(CN1201)
RB DVD mechanism deck
(CDM81C-DVBU101)
wire (flat type) (21 core)
(SERIPARA board: CN651,
RELAY board: CN701)
two insulator screws
Be sure to bridge here, and then disconnect the wire (flat type) (24 core).
(optical pick-up block will be destroyed without bridging)
On the contrary at the installation, connect the
wire (flat type) (24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
(Refer to DISASSEMBLY 3-12. OPTICAL PICK-UP BLOCK (KHM-310CAB or KHM-313CAB))
PRECAUTION WHEN REMOVING DVD MECHANISM DECK
(CDM81C-DVBU101)
(CDM81C-DVBU101)
Perform work with this wire (flat type) (24 core) connected,
or make a bidge as mentioned above and then disconnect
the wire (flat type) (24 core).
(optical pick-up block will be destroyed without bridging.)
On the contrary at the installation, connect the
wire (flat type) (24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
HCD-HDX285/HDX287WC/HDX585/HDX587WC/HDX589W/HDX685/HDX686W
16
RB screw
(BV3
(3-CR))
RH three screws
(BV3
(3-CR))
RE screw
(BV3
(3-CR))
RL six screws
(BV3
(3-CR))
RL two screws
(BV3
(3-CR))
R two connectors
(CN904,
CN906)
connector
(CN001)
wire (flat type) (5 core)
(CN003)
SERIPARA board
RM MAIN board
"
"
#
#
wire (flat type) (5 core)
(CN303)
wire (flat type) (9 core)
(CN502)
wire (flat type) (17 core)
(CN472)
RK three radiation
sheets
RK two radiation
sheets
XT two radiation
sheets
screw
(BV3
(3-CR))
three screws
(BV3
(3-CR))
RI heatsink (DDV)
RT HEATSINK A board
RG HEATSINK B board
(HDX285/HDX287WC/HDX585/
HDX587WC/HDX685)
HDX587WC/HDX685)
(HDX285: US/HDX287WC/
HDX585/HDX587WC/HDX589W/
HDX685/HDX686W)
HDX585/HDX587WC/HDX589W/
HDX685/HDX686W)
screw
(B3
× 6)
two screws
(BV3
(3-CR))
screw
(BV3
(3-CR))
SPEAKER board
connector
(CN5300:
(HDX589W/HDX686W),
CN5301:
HDX285/HDX287WC
/HDX585/HDX587WC/HDX685)
3-9. SPEAKER BOARD
3-10. MAIN BOARD
Click on the first or last page to see other DAV-HDX285 / DAV-HDX287WC / DAV-HDX585 / DAV-HDX587WC / DAV-HDX589W / DAV-HDX685 / DAV-HDX686W / HCD-HDX285 / HCD-HDX287WC / HCD-HDX585 / HCD-HDX587WC / HCD-HDX685 / HCD-HDX686W service manuals if exist.