Sony DAV-FXG9K / HCD-FXG9K Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Audio Business Group
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
E Model
Australian Model
Russia Model
SUPER AUDIO CD/DVD RECEIVER
9-887-299-03
2007L04-1
© 2007.12
© 2007.12
Ver. 1.2 2007.12
SPECIFICATIONS
HCD-FXG9K
Amplifier section
Stereo mode (rated)
Stereo mode (rated)
150 W + 150 W (4 ohms at
1 kHz, 1 % THD)
1 kHz, 1 % THD)
Surround mode (reference) RMS output power, 10 % THD
Front: 180 W + 180 W
(with SS-TS57)
Center*: 180 W
(with SS-CT53)
Surround*: 180 W + 180 W
(with SS-TS57R)
Subwoofer*: 300 W
(with SS-WS54)
(with SS-TS57)
Center*: 180 W
(with SS-CT53)
Surround*: 180 W + 180 W
(with SS-TS57R)
Subwoofer*: 300 W
(with SS-WS54)
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
TV/VCR 1, TV/VCR 2 (AUDIO IN)
TV/VCR 1, TV/VCR 2 (AUDIO IN)
Sensitivity: 450/250 mV
AUDIO IN/MIC 1
Sensitivity:
AUDIO IN 250/125 mV/
MIC 1 1 mV
AUDIO IN 250/125 mV/
MIC 1 1 mV
MIC 2
Sensitivity: 1 mV
Inputs (Digital)
TV/VCR1 (COAXIAL IN)/TV/VCR2 (OPTICAL IN)
TV/VCR1 (COAXIAL IN)/TV/VCR2 (OPTICAL IN)
impedance: 75 ohms/–
Super Audio CD/DVD system
Laser
Laser
Semiconductor laser
(Super Audio CD/DVD:
λ = 650 nm)
(CD:
(Super Audio CD/DVD:
λ = 650 nm)
(CD:
λ = 790 nm)
Emission duration: continuous
Signal format system
NTSC/PAL
Tuner section
System
System
PLL quartz-locked digital
synthesizer system
synthesizer system
FM tuner section
Tuning range
Tuning range
87.5-108.0 MHz (50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Tuning range
530-1,710 kHz (with the
interval set at 10 kHz)
531-1,602 kHz (with the
interval set at 9 kHz)
interval set at 10 kHz)
531-1,602 kHz (with the
interval set at 9 kHz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
This system incorporates with Dolby* Digital and Dolby Pro Logic (II)
adaptive matrix surround decoder and the DTS** Digital Surround System.
adaptive matrix surround decoder and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of
Dolby Laboratories.
Dolby Laboratories.
**Manufactured under license from Digital Theater Systems, Inc.
“DTS” and “DTS Digital Surround” are registered trademarks of
Digital Theater Systems, Inc.
Digital Theater Systems, Inc.
Model Name Using Similar Mechanism
HCD-FX900KW
Mechanism Type
CDM69EH-DVBU101
Optical Pick-up Name
KHM-310CAB/C2NP
– Continued on next page –
• HCD-FXG9K is the amplifier, DVD/CD
and tuner section in DAV-FXG9K.
2
HCD-FXG9K
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Video section
Outputs
Outputs
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
HDMI OUT: Type A (19 pin)
HDMI OUT: Type A (19 pin)
Inputs
VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
General
Power requirements
Power requirements
220 - 240 V AC, 50/60 Hz
Power consumption
On: 210 W
Standby: 0.3 W (at the
Power Saving Mode)
Standby: 0.3 W (at the
Power Saving Mode)
Dimensions (approx.)
445
× 71 × 405 mm (w/h/d)
incl. projecting parts
Mass (approx.)
6.0 kg
Design and specif ications ar e subject to c hang e
without notice .
without notice .
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear of the unit.
classified as a CLASS 1
LASER product. This
marking is located on the
rear of the unit.
MODEL IDENTIFICATION
– Back Panel –
• Abbreviation
E3
: AC 240 V area in E model
AUS : Australian model
RU : Russia model
KR : Korea model
SP
RU : Russia model
KR : Korea model
SP
: Singapore model
TH : Thai model
Parts No.
Model
Parts No.
KR, SP, TH model
2-682-126-0s
AUS model
2-682-126-2s
E3 model
2-682-126-3s
RU model
2-682-126-4s
Ver. 1.1
3
HCD-FXG9K
• The instructions in this manual describe the
controls on the remote. You can also use the
controls on the system if they have the same or
similar names as those on the remote.
controls on the system if they have the same or
similar names as those on the remote.
• The Control Menu items may be different
depending on the area.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD+RWs/DVD+Rs, and
DVD-RWs/DVD-Rs.
DVD-RWs/DVD-Rs.
• Measurements are expressed in feet (ft) for
North American models.
• The following symbols are used in this
manual.
1)
MP3 (MPEG1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio data.
2)
DivX
®
is a video file compression technology,
developed by DivX, Inc.
3)
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under license.
trademarks of DivX, Inc. and are used under license.
About This Manual
Symbol
Meaning
Functions available for DVD
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
Functions available for DVD-Rs/
DVD-RWs in VR (Video
Recording) mode
DVD-RWs in VR (Video
Recording) mode
Functions available for VIDEO
CDs (including Super VCDs or CD-
Rs/CD-RWs in video CD format or
Super VCD format)
CDs (including Super VCDs or CD-
Rs/CD-RWs in video CD format or
Super VCD format)
Functions available for Super Audio
CDs
CDs
Functions available for music CDs
or CD-Rs/CD-RWs in music CD
format, including discs containing
CD Graphics (Latin American
models only)
or CD-Rs/CD-RWs in music CD
format, including discs containing
CD Graphics (Latin American
models only)
Functions available for DATA CDs
(CD-ROMs/CD-Rs/CD-RWs)
containing MP3
(CD-ROMs/CD-Rs/CD-RWs)
containing MP3
1)
audio tracks,
JPEG image files, and DivX
2)3)
video files
Functions available for DATA
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs/DVD+Rs/DVD+RWs)
containing MP3
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs/DVD+Rs/DVD+RWs)
containing MP3
1)
audio tracks,
JPEG image files, and DivX
2)3)
video files
4
HCD-FXG9K
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD VIDEO,” and the “CD” logos are trademarks.
“DVD VIDEO,” and the “CD” logos are trademarks.
Note about CDs/DVDs
The system can play CD-ROMs/CD-Rs/CD-
RWs recorded in the following formats:
RWs recorded in the following formats:
– audio CD format
– CD Graphics (Latin American models only)
– video CD format
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to ISO
9660 Level 1/Level 2, or its extended format,
Joliet
9660 Level 1/Level 2, or its extended format,
Joliet
The system can play DVD-ROMs/DVD+RWs/
DVD-RWs/DVD+R s/DVD-Rs recorded in the
following formats:
DVD-RWs/DVD+R s/DVD-Rs recorded in the
following formats:
– MP3 audio tracks, JPEG image files and
DivX video files of format conforming to
UDF (Universal Disc Format)
UDF (Universal Disc Format)
Example of discs that the
system cannot play
The system cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than those
• CD-ROMs/CD-Rs/CD-RWs other than those
recorded in the formats listed on page 6
• CD-ROMs recorded in PHOTO CD format
• Data part of CD-Extras
• DVD Audios
• DATA DVDs that do not contain MP3 audio
• Data part of CD-Extras
• DVD Audios
• DATA DVDs that do not contain MP3 audio
tracks, JPEG image files, or DivX video files.
• DVD-RAMs
Also, the system cannot play the following
discs:
• A DVD VIDEO with a different region code
• A disc that has a non-standard shape (e.g.,
discs:
• A DVD VIDEO with a different region code
• A disc that has a non-standard shape (e.g.,
card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape
• A disc that has the adhesive of cellophane tape
or a sticker still left on it
Notes about CD-R/CD-RW/DVD-R/
DVD-RW/DVD+R/DVD+RW
DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVD-
RW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
RW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
This System Can Play the
Following Discs
Following Discs
Format of
discs
discs
Disc logo
DVD VIDEO
DVD-RW/
DVD-R
DVD-R
DVD+RW/
DVD+R
DVD+R
Super Audio
CD
CD
VIDEO CD
(Ver. 1.1 and
2.0 discs)/CD
Graphics
(Latin
American
models only)/
Audio CD
(Ver. 1.1 and
2.0 discs)/CD
Graphics
(Latin
American
models only)/
Audio CD
CD-RW/CD-R
(audio data)
(MP3 files)
(JPEG files)
(audio data)
(MP3 files)
(JPEG files)