Sony DAV-DZ970WA / HCD-DZ970WA Service Manual ▷ View online
HCD-DZ970WA
8
1.
SERVICING NOTES
............................................. 9
2. GENERAL
.................................................................. 11
3. DISASSEMBLY
3-1. Case ................................................................................ 15
3-2. POWER
3-2. POWER
Board
................................................................ 15
3-3. Front Panel Section ........................................................ 16
3-4. Back Panel Section ......................................................... 16
3-5. DVD Mechanism Deck ................................................... 17
3-6. MAIN
3-4. Back Panel Section ......................................................... 16
3-5. DVD Mechanism Deck ................................................... 17
3-6. MAIN
Board
................................................................... 17
3-7. IO-COMPONENT Board, SCORE Board ...................... 18
3-8. Tray
3-8. Tray
................................................................................. 18
3-9. Belt
.................................................................................. 19
3-10. MS-203 Board ................................................................. 19
3-11. Base Unit ......................................................................... 20
3-12. Optical Pick-up ............................................................... 20
3-11. Base Unit ......................................................................... 20
3-12. Optical Pick-up ............................................................... 20
4.
TEST MODE
............................................................ 21
5. ELECTRICAL
ADJUSTMENTS
........................ 26
6. DIAGRAMS
6-1. Block Diagram –RF Section– ......................................... 29
6-2. Block Diagram –VIDEO Section– ................................. 30
6-3. Block Diagram –AUDIO Section– ................................. 31
6-4. Block Diagram –DSP Section– ....................................... 32
6-5. Block Diagram –AMP Section– ..................................... 33
6-6. Block Diagram –POWER Section– ................................ 34
6-7. Printed Wiring Board –MAIN Board (Side A)– ............. 35
6-8. Printed Wiring Board –MAIN Board (Side B)– ............. 36
6-9. Schematic Diagram –MAIN Board (1/9)– ...................... 37
6-10. Schematic Diagram –MAIN Board (2/9)– ...................... 38
6-11. Schematic Diagram –MAIN Board (3/9)– ...................... 39
6-2. Block Diagram –VIDEO Section– ................................. 30
6-3. Block Diagram –AUDIO Section– ................................. 31
6-4. Block Diagram –DSP Section– ....................................... 32
6-5. Block Diagram –AMP Section– ..................................... 33
6-6. Block Diagram –POWER Section– ................................ 34
6-7. Printed Wiring Board –MAIN Board (Side A)– ............. 35
6-8. Printed Wiring Board –MAIN Board (Side B)– ............. 36
6-9. Schematic Diagram –MAIN Board (1/9)– ...................... 37
6-10. Schematic Diagram –MAIN Board (2/9)– ...................... 38
6-11. Schematic Diagram –MAIN Board (3/9)– ...................... 39
TABLE OF CONTENTS
6-12. Schematic Diagram –MAIN Board (4/9),
MS-203
MS-203
Board–
...............................................................
40
6-13. Schematic Diagram –MAIN Board (5/9)– ...................... 41
6-14. Schematic Diagram –MAIN Board (6/9)– ...................... 42
6-15. Schematic Diagram –MAIN Board (7/9)– ...................... 43
6-16. Schematic Diagram –MAIN Board (8/9)– ...................... 44
6-17. Schematic Diagram –MAIN Board (9/9)– ...................... 45
6-18. Printed Wiring Board –IO-COMPONENT Board– ........ 46
6-19. Schematic Diagram –IO-COMPONENT Board– ........... 47
6-20. Printed Wiring Boards –JACK, P-SW Board– ............... 48
6-21. Schematic Diagram –JACK, P-SW Board– .................... 49
6-22. Printed Wiring Boards
6-14. Schematic Diagram –MAIN Board (6/9)– ...................... 42
6-15. Schematic Diagram –MAIN Board (7/9)– ...................... 43
6-16. Schematic Diagram –MAIN Board (8/9)– ...................... 44
6-17. Schematic Diagram –MAIN Board (9/9)– ...................... 45
6-18. Printed Wiring Board –IO-COMPONENT Board– ........ 46
6-19. Schematic Diagram –IO-COMPONENT Board– ........... 47
6-20. Printed Wiring Boards –JACK, P-SW Board– ............... 48
6-21. Schematic Diagram –JACK, P-SW Board– .................... 49
6-22. Printed Wiring Boards
–FL, MS-203, SPEAKER Board– .................................. 50
6-23. Schematic Diagram –FL, SPEAKER Board– ................. 51
6-24. Printed Wiring Board –DSP Board (Side A)– ................. 52
6-25. Printed Wiring Board –DSP Board (Side B)– ................. 53
6-26. Schematic Diagram –DSP Board– .................................. 54
6-27. Printed Wiring Board –S-AIR-CON Board– .................. 55
6-28. Schematic Diagram –S-AIR-CON Board– ..................... 56
6-29. Printed Wiring Board –SERIPARA Board–.................... 57
6-30. Schematic Diagram –SERIPARA Board– ...................... 58
6-31. Printed Wiring Board –SCORE Board– ......................... 59
6-32. Schematic Diagram –SCORE Board– ............................ 60
6-33. Printed Wiring Board –POWER Board– ........................ 61
6-34. Schematic Diagram –POWER Board– ........................... 62
6-24. Printed Wiring Board –DSP Board (Side A)– ................. 52
6-25. Printed Wiring Board –DSP Board (Side B)– ................. 53
6-26. Schematic Diagram –DSP Board– .................................. 54
6-27. Printed Wiring Board –S-AIR-CON Board– .................. 55
6-28. Schematic Diagram –S-AIR-CON Board– ..................... 56
6-29. Printed Wiring Board –SERIPARA Board–.................... 57
6-30. Schematic Diagram –SERIPARA Board– ...................... 58
6-31. Printed Wiring Board –SCORE Board– ......................... 59
6-32. Schematic Diagram –SCORE Board– ............................ 60
6-33. Printed Wiring Board –POWER Board– ........................ 61
6-34. Schematic Diagram –POWER Board– ........................... 62
7.
EXPLODED VIEWS
7-1. Overall
Section
............................................................... 80
7-2. Front Panel Section ......................................................... 81
7-3. Chassis
7-3. Chassis
Section
............................................................... 82
7-4. DVD Mechanism Deck Section (CDM85-DVBU102) .. 83
8.
ELECTRICAL PARTS LIST
.............................. 84
HCD-DZ970WA
9
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
How to open the disc table when power switch turns off
Insert a tapering driver into the aperture of the unit bottom, and
slide it in the direction of the arrow.
Insert a tapering driver into the aperture of the unit bottom, and
slide it in the direction of the arrow.
Precaution when installing a new OP unit/
Precaution before unsoldering the static electricity
prevention solder bridge
Precaution before unsoldering the static electricity
prevention solder bridge
When installing a new OP unit, be sure to connect the fl exible
printed circuit board fi rst of all before removing the static electricity
prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by
unsoldering after the fl exible printed circuit board has already been
connected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)
printed circuit board fi rst of all before removing the static electricity
prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by
unsoldering after the fl exible printed circuit board has already been
connected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)
Peel off the seal and so the lever is moved
in the direction of the arrow with the thin rod.
in the direction of the arrow with the thin rod.
tray
seal
On cleaning discs, disc/lens cleaners
• Do not use cleaning discs or disc/lens cleaners (including wet or
• Do not use cleaning discs or disc/lens cleaners (including wet or
spray types). These may cause the apparatus to malfunction.
IMPORTANT NOTICE
Caution: This system is capable of holding a still video image or
on-screen display image on your television screen indefi nitely.
If you leave the still video image or on-screen display image
displayed on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to this.
Caution: This system is capable of holding a still video image or
on-screen display image on your television screen indefi nitely.
If you leave the still video image or on-screen display image
displayed on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to this.
Attention when transported
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
?/1
] button to turn the set on.
2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press two buttons [
3. Remove all discs, and then press two buttons [
H
] and [
?/1
]
simultaneously.
4. After a message “MECHA LOCK” is displayed on the
fl uorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the [
?/1
] button to turn the set
on.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the [
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the [
?/1
] button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the [
3. Insert a disc.
4. Press the [
x
] button and the [
A
] button simultaneously for fi ve
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the [
Releasing Procedure :
1. Press the [
x
] button and the [A] button simultaneously for fi ve
seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note: When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the [?/1] button.
LASER DIODE AND FOCUS SEARCH
1. Open the case and turn POWER on with no disc inserted.
2. Confi rm that the following operation is performed while
1. Open the case and turn POWER on with no disc inserted.
2. Confi rm that the following operation is performed while
observing the objecting lens from the clearance of DVD
mechanism deck.
1) Confi rm that laser beam is spread.
2) Up and down motion of the objective lens. (2 times)
mechanism deck.
1) Confi rm that laser beam is spread.
2) Up and down motion of the objective lens. (2 times)
HCD-DZ970WA
10
Radiation Sheet
When peeling off the heat radiation sheet, try always to put it on
be former position.
When peeling off the heat radiation sheet, try always to put it on
be former position.
radiation sheet
POWER board
HCD-DZ970WA
11
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.
" / (on/standby) (29, 98)
# " (open/close) (38)
$ Front panel display (118)
% Play operation buttons (38)
&
(remote sensor) (9)
' FUNCTION (32)
( VOLUME control (38)
) MIC2 jack (90)
* AUDIO IN/MIC1/A.CAL MIC jack (23, 29,
87)
+
(USB) port (71)
, Disc tray (38)
Front panel
Ad
dition
dition
al
Inf
Inf
o
rm
atio
n
" SPEAKER jacks (20)
# EZW-T100 slot (23)
$ COAXIAL 75Ω FM jack (25)
% AM terminal (25)
& SAT/CABLE (AUDIO IN R/L) jacks (23)
' TV (AUDIO IN R/L) jacks (21)
( VIDEO OUT jack (21)
) COMPONENT VIDEO OUT jacks (21)
* DMPORT (DIGITAL MEDIA PORT) jack
(23, 80)
+ HDMI OUT jack (21)
, TV (DIGITAL IN COAXIAL/OPTICAL)
jacks (21)
*
CAUTION
Please do not remove the screws before
installing the EZW-T100.
installing the EZW-T100.
Rear panel
CENTER
SUBWOOFER
AUDIO IN
COAXIAL 75
AM
FM
P
B
/C
B
P
R
/C
R
Y
L
R
FRONT R
FRONT L
SUR R
SUR L
SPEAKER
HDMI OUT
VIDEO OUT
TV
ANTENNA
DMPORT
SPEAKER
COMPONENT VIDEO OUT
AUDIO IN
L
R
SAT/CABLE
EZW-T100
DC5V
0.7A MAX
DIGITAL IN
COAXIAL
OPTICAL
TV
Screws*
Click on the first or last page to see other DAV-DZ970WA / HCD-DZ970WA service manuals if exist.