DOWNLOAD Sony DAV-DZ680W / DAV-DZ880W / HCD-DZ680W / HCD-DZ880W Service Manual ↓ Size: 4.78 MB | Pages: 92 in PDF or view online for FREE

2010C04-1

© 

2010.03

Model Name Using Similar Mechanism

HCD-DZ280/DZ680

Mechanism Type

CDM85-DVBU102

Optical Pick-up Name

KHM-313CAA

•  HCD-DZ380W/DZ680W/DZ880W are the amplifi er, DVD/CD 

and tuner section in DAV-DZ380W/DZ680W/DZ880W.

Stereo mode (rated) 

108 W + 108 W (at 3 ohms,

 

1 kHz, 1% THD)

DZ680W:
Surround mode (reference) RMS output power
 

FL/FR/C*: 142 watts (per 

 

channel at 3 ohms, 1 kHz, 

 10% 

THD)

 

Subwoofer*: 140 watts (at

 

3 ohms, 80 Hz, 10% THD)

DZ880W:
Surround mode (reference) RMS output power
 

FL/FR/C*: 144 watts (per 

 

channel at 3 ohms, 1 kHz, 

 10% 

THD)

 

Subwoofer*: 280 watts (at

 

1.5 ohms, 80 Hz, 10% THD)

Inputs (Analog)
TV (AUDIO IN) 

Sensitivity: 450/250 mV

LINE (AUDIO IN) (DZ880W only)
 

Sensitivity: 450/250 mV

AUDIO IN 

Sensitivity: 250/125 mV

Inputs (Digital)
TV (COAXIAL IN/OPTICAL IN)
 

Impedance: 75 ohms/-

 

Input Stream: Dolby

 

Digital 5.1ch/DTS 5.1ch/

 

Linear PCM 2ch

 

(Sampling Frequency: less

 

than 48 kHz)

Outputs (Analog)
Phones 

Accepts low- and high-

 impedance 

headphones.

Laser Diode Properties 

Emission Duration:

 Continuous
 

Laser Output: Less than

 44.6

μW

* This output is the value measurement at a distance
  of 200mm from the objective lens surface on the
  Optical Pick-up Block with 7mm aperture.

Signal format system 

PAL/NTSC

 (USB) port:

Maximum current: 

500 mA

System 

PLL quartz-locked digital

 synthesizer
FM Tuner section
Tuning range
North American models:  87.5 MHz - 108.0 MHz
 

(100 kHz step)

Other models: 

87.5 MHz - 108.0 MHz

 

(50 kHz step)

Antenna (aerial) 

FM wire antenna (aerial)

Antenna (aerial) terminals  75 ohms, unbalanced
Intermediate frequency 

10.7 MHz

Outputs 

VIDEO: 1 Vp-p 75 ohms

 

R/G/B: 0.7 Vp-p 75 ohms

 

HDMI OUT: Type A (19 

 pin)

– Continued on next page –

Photo: HCD-DZ880W

This system incorporates with Dolby* Digital and Dolby Pro Logic (II) 
adaptive matrix surround decoder and the DTS** Digital Surround System.
*  Manufactured under license from Dolby Laboratories.
 

Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby 
Laboratories.

**  Manufactured under license under U.S. Patent #’s:
 

5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and 
worldwide patents issued & pending. DTS and DTS Digital Surround are 
registered trademarks and the DTS logos and Symbol are trademarks of 
DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved.

COMPONENTS  IDENTIFIED  BY  MARK  0  OR  DOTTED  LINE  
WITH  MARK  0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS 

Power requirements 

220 V - 240 V AC,

 50/60 

Hz

Power consumption 

On: 110 W

 

Standby: 0.3 W (at the

 

Power Saving mode)

Output voltage (DIGITAL MEDIA PORT) 
 DC 

5 

V

Output current (DIGITAL MEDIA PORT) 
 700 

mA

Dimensions (approx.) 

430 mm 

× 66 mm × 395 mm 

 

(w/h/d) incl. projecting parts

 430 

mm 

× 66 mm × 425 mm 

 

(w/h/d) with the wireless 

 transceiver 

inserted

Mass (approx.) 

4.3 kg

File Extension: 

mp3

Bitrate: 

32 kbps - 320 kbps

Sampling frequencies: 

32/44.1/48 kHz

File Extension: 

wma

Bitrate: 

48 kbps - 192 kbps

Sampling frequencies: 

44.1 kHz

File Extension: 

m4a

Bitrate: 

48 kbps - 320 kbps

Sampling frequencies: 

44.1 kHz

File Extension: 

avi/divx

Video codec: 

DivX video

Bitrate: 

8 Mbps (MAX)

Frame rate: 

30 fps

Resolution: 720 

× 576

Audio codec: 

MP3

File format: 

MP4 File Format

File Extension: 

mp4/m4v

Video codec: 

MPEG4 Simple Profi le

 

(AVC is not compatible.)

Bitrate: 4 

Mbps

Frame rate: 

30 fps

Resolution: 720 

× 576

Audio codec: 

AAC-LC (HE-AAC is not

 compatible.)
DRM: Not 

compatible

Design and specifi cations are subject to change
without notice.

SPECIAL  COMPONENT  NOTICE
The components identifi ed by mark 9 contain confi dential infor-
mation.
Strictly follow the instructions whenever the components are re-
paired and/or replaced.

DZ880W

4-113-461-2[]

DZ680W

4-122-168-7[]

UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 

than ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if 

the heated tip is applied for too long, so be careful!

• Strong 

viscosity

 

Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.

•  Usable with ordinary solder
 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

NOTES  ON  CHIP  COMPONENT  REPLACEMENT
•  Never reuse a disconnected chip component.
•  Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

FLEXIBLE  CIRCUIT  BOARD  REPAIRING
•  Keep the temperature of soldering iron around 270 °C during 

repairing.

•  Do not touch the soldering iron on the same conductor of the 

circuit board (within 3 times).

•  Be careful not to apply force on the conductor when soldering 

or unsoldering.

Laser component in this product is capable of emitting radiation 
exceeding the limit for Class 1.

This appliance is classifi ed as 
a CLASS 1 LASER product.
This marking is located on the 
rear or bottom exterior.

CAUTION
Use of controls or adjustments or performance of procedures 
other than those specifi ed herein may result in hazardous radia-
tion exposure.

Playable Discs

1)

MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG for compresses audio data. MP3 files

must be in MPEG1 Audio Layer 3 format.

2)

JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File system”: Image

standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association
(JEITA).)

O

E

D

I

V

D

V

D

•

O

E

D

I

V

D

V

D

• DVD-R/DVD-RW in DVD VIDEO

format or video mode

• DVD+R/DVD+RW in DVD VIDEO

format

VR (Video
Recording) mode

• DVD-R/DVD-RW in VR (Video

Recording) mode (except for DVD-R
DL)

)

s

c

s

i

d

0

.

2

d

n

a

1

.

1

.

r

e

V

(

D

C

O

E

D

I

V

•

D

C

O

E

D

I

V

• Super VCD

• CD-R/CD-RW/CD-ROM in video CD

format or Super VCD format

D

C

o

i

d

u

A

r

e

p

u

S

•

D

C

o

i

d

u

A

r

e

p

u

S

D

C

o

i

d

u

A

•

D

C

• CD-R/CD-RW in audio CD format

DATA CD

     

–

• CD-R/CD-RW/CD-ROM in DATA CD

format, containing MP3 files

1)

, JPEG

image files

2)

, DivX video files, and

MPEG4 video files, and conforming to
ISO 9660

3)

Level 1/Level 2, or Joliet

(extended format)

DATA DVD

     

–

• DVD-ROM/DVD-R/DVD-RW/

DVD+R/DVD+RW in DATA DVD
format, containing MP3 files

1)

, JPEG

image files

2)

, DivX video files, and

MPEG4 video files, and conforming to
UDF (Universal Disk Format)