Sony DAV-DZ531W (serv.man2) Service Manual ▷ View online
13
HCD-DZ531W
SECTION 3
DISASSEMBLY
3-1. DISASSEMBLY FLOW
•
This set can be disassembled in the order shown below.
3-3. FL BOARD
(Page 15)
3-4. JACK BOARD,
P-SW BOARD
(Page 16)
3-5. FRONT PANEL,
ORNAMENT
(Page 16)
3-13. DVD MECHANISM DECK
(CDM85-DVBU102)
(Page 21)
3-14. TRAY
(Page 21)
3-15. BELT,
MS-203 BOARD
(Page 22)
3-16. OPTICAL PICK-UP
(KHM-313CAA)
(Page 23)
3-12. MAIN BOARD,
DSP BOARD
(Page 20)
3-7. DMPORT BOARD
(Page 17)
3-8. DIAT-TX BOARD
(Page 18)
3-10. IO-SCART BOARD
(Page 19)
3-11. SPEAKER BOARD,
D.C. FAN
(Page 19)
3-9. POWER BOARD
(Page 18)
3-6. TUNER (FM/AM)
(Page 17)
3-2. CASE (DS),
FRONT PANEL ASSY
(Page 14)
SET
14
HCD-DZ531W
3-2. CASE (DS), FRONT PANEL ASSY
Note:
Follow the disassembly procedure in the numerical order given.
qf
two screws
(+BVTP
2.6
×
10)
q;
wire (flat type)
21core (CN502)
2
The lever is moved in the direction
of the arrow with the thin rod.
1
seal
3
4
loading panel
5
two screws
(CASE 3
(CASE 3
×
8 TP2)
8
case (DS)
qj
front panel assy
qd
four screws
(+BV 3
(+BV 3
×
6)
qs
connector 4P (CN3001)
qh
three claws
qg
three
claws
claws
6
two screws
(CASE 3
×
8 TP2)
7
five screws
(+BVTP 3
×
8)
9
unweaved
cloth
cloth
rib
notch
harness
rib
lead pin
Route the harness as shown below.
qa
connector 4P (CN302)
15
HCD-DZ531W
3-3. FL BOARD
PRECAUTION DURING THE RETAINER (DS) INSTALLATION
(2) Route the harness as shown below.
(3) Route the harness as shown below.
(1) Assemble seven claws securely.
4
shield plate (FR)
shield plate (FR)
front panel
8
FL board
FL board
JACK
board
board
CN806
CN805
3
five screws
(+BVTP 2.6
(+BVTP 2.6
×
10)
5
two screws
(+BVTP 2.6
(+BVTP 2.6
×
10)
1
two
rivets
rivets
6
wire (flat type)
13core (CN805)
wire (flat type) 13core
7
wire (flat type)
21core (CN801)
2
retainer (DS)
retainer (DS)
harness
rivet
rivet
hole
retainer (DS)
harness
wire (flat type)
groove
groove
retainer (DS)
hole
Route the wire
(flat type) 13core
as shown in the figure.
(flat type) 13core
as shown in the figure.
16
HCD-DZ531W
3-5. FRONT PANEL, ORNAMENT
3-4. JACK BOARD, P-SW BOARD
Route the harness as shown below.
JACK board
JACK board
(NG)
(OK)
1
knob (vol)
2
nut
qa
JACK board
4
button (base)
5
wire (flat type)
13core (CN806)
13core (CN806)
8
Remove the
solderings.
9
harness
3
four screws
(+BVTP
(+BVTP
2.6
×
10)
6
screw
(+BVTP
2.6
×
10)
7
button (base)
q;
P-SW board
JACK board
JACK board
Route the harness as shown below.
(NG)
(OK)
2
six claws
6
ornament
3
front panel
1
screw
(+BVTP
2.6
×
10)
4
six claws
5
button (cap)
Click on the first or last page to see other DAV-DZ531W (serv.man2) service manuals if exist.