Sony DAV-DZ350 / DAV-DZ650 / DAV-DZ950 Service Manual ▷ View online
DAV-DZ350/DZ650/DZ950
5
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
DVD MECHANISM DECK SERVICE POSITION
2 Pull out the disc tray.
ditch
1 Insert the tweezers etc. in the hole of the
chassis, and slide the lever in the direction
of the arrow.
– Bottom view –
– Bottom view –
DVD mechanism deck
(CMS-LS5FP)
(CMS-LS5FP)
MAIN board
front panel block
insulating sheet
DAV-DZ350/DZ650/DZ950
6
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. TOP COVER (DJ)
2-2. TOP COVER (DJ)
(Page
(Page
6)
SET
2-3. DVD
DOOR
ASSY
(Page
7)
2-4. POWER
BOARD
(Page
7)
2-14. MIC BOARD
(Page
(Page
16)
2-15. MAIN BOARD
(Page
(Page
17)
2-5. FRONT PANEL BLOCK
(Page
(Page
8)
2-6. BT
ANTENNA
(ANT1),
POWER KEY BOARD,
FUNCTION KEY BOARD
(Page
9)
2-7. DVD MECHANISM DECK BLOCK
(Page
(Page
10)
2-8. DVD MECHANISM DECK
(CMS-LS5FP)
(Page
(CMS-LS5FP)
(Page
11)
2-9. HOLDER
CHUCK
(Page
12)
2-10. TRAY DISC-1
(Page
(Page
12)
2-11. TRAY DISC-2
(Page
(Page
13)
2-12. OPTICAL PICK-UP BLOCK-1
(Page
(Page
14)
2-13. OPTICAL PICK-UP BLOCK-2
(Page
(Page
15)
4 top cover (DJ)
1 screw (BVTT3 u 6)
1 screw
(BVTT3
(BVTT3
u 6)
1 five screws
(BVTT3
(BVTT3
u 6)
3 six claws
2 Remove the top cover (DJ)
in the direction of an arrow.
Ver. 1.3
DAV-DZ350/DZ650/DZ950
7
2-3. DVD DOOR ASSY
3 five claws
4 DVD door assy
2 Pull out the disc tray.
ditch
1 Insert the tweezers etc. in the hole of the
chassis, and slide the lever in the direction
of the arrow.
– Bottom view –
– Bottom view –
2-4. POWER BOARD
4 POWER board
POWER board
1 power cord connector
(CN901)
(CN901)
2 connector
(CN400)
(CN400)
3 three screws
(BVTT3
(BVTT3
u 7)
3 two screws
(BVTT3
(BVTT3
u 7)
3RZHUFRUGVHWWLQJ
power cord
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
DAV-DZ350/DZ650/DZ950
8
2-5. FRONT PANEL BLOCK
7 six claws
7 five claws
0 front panel block
2 connector
(CN201)
(CN201)
5 BT antenna
connector
(SMC600)
connector
(SMC600)
4 Remove the bond.
3 connector
(CN202)
(CN202)
6 two claws
1 Cut two wire ties.
– Rear view –
tray
Wire setting
wire tie
claw
claw
wire tie
MAIN board
POWER board
DVD mechanism deck
(CMS-LS5FP)
(CMS-LS5FP)
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
Bring the slack part to the front side.
Note 1: In reassembling,
use new wire tie
to fasten the clamp
same as before.
8 Remove the front panel block
in the direction of an arrow.
9 Draw out two wires.
9 Draw out the wire.
Note 2: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Click on the first or last page to see other DAV-DZ350 / DAV-DZ650 / DAV-DZ950 service manuals if exist.