Sony DAV-DZ260 / DAV-DZ270 / HCD-DZ260 / HCD-DZ270 / HCD-HDZ278 Service Manual ▷ View online
HCD-DZ260/DZ270/HDZ278
9
SECTION 1
SERVICING NOTES
How to open the disc table when power switch turns off
Insert a tapering driver into the aperture of the unit bottom, and
slide it in the direction of the arrow.
Insert a tapering driver into the aperture of the unit bottom, and
slide it in the direction of the arrow.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the [
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the [
?/1
] button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the [
3. Insert a disc.
4. Press the [
x
] button and the [
A
] button simultaneously for fi ve
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press the [
Releasing Procedure :
1. Press the [
x
] button and the [
A
] button simultaneously for fi ve
seconds again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note: When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the [
?/1
] button.
On cleaning discs, disc/lens cleaners
• Do not use cleaning discs or disc/lens cleaners (including wet or
• Do not use cleaning discs or disc/lens cleaners (including wet or
spray types). These may cause the apparatus to malfunction.
IMPORTANT NOTICE
Caution: This system is capable of holding a still video image or
on-screen display image on your television screen indefi nitely.
If you leave the still video image or on-screen display image
displayed on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to this.
Caution: This system is capable of holding a still video image or
on-screen display image on your television screen indefi nitely.
If you leave the still video image or on-screen display image
displayed on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to this.
Attention when transported
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the [
?/1
] button to turn the set on.
2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press two buttons [
3. Remove all discs, and then press two buttons [
H
] and [
?/1
]
simultaneously.
4. After a message “MECHA LOCK” is displayed on the
fl uorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the [
?/1
] button to turn the set
on.
Peel off the seal and so the lever is moved
in the direction of the arrow with the thin rod.
in the direction of the arrow with the thin rod.
tray
seal
Precaution when installing a new OP unit/
Precaution before unsoldering the static electricity
prevention solder bridge
Precaution before unsoldering the static electricity
prevention solder bridge
When installing a new OP unit, be sure to connect the fl exible
printed circuit board fi rst of all before removing the static electricity
prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by
unsoldering after the fl exible printed circuit board has already been
connected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)
printed circuit board fi rst of all before removing the static electricity
prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by
unsoldering after the fl exible printed circuit board has already been
connected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)
HCD-DZ260/DZ270/HDZ278
10
Radiation Sheet
When peeling off the heat radiation sheet, try always to put it on
be former position.
When peeling off the heat radiation sheet, try always to put it on
be former position.
Ver. 1.1
radiation sheet
POWER board
HCD-DZ260/DZ270/HDZ278
11
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Index to Parts and Control
(DZ260)
For more information, refer to the pages indicated in parentheses.
" / (on/standby) (20, 78)
# " (open/close) (28)
$ Front panel display (96)
% Play operation buttons (28)
&
(remote sensor) (9)
' FUNCTION (23)
( VOLUME control (28)
) PHONES jack (28)
* AUDIO IN/A.CAL MIC jack (16, 20, 72)
+
(USB) port (60)
, Disc tray (28)
Front panel
Ad
dit
iona
dit
iona
l
Inf
o
o
rma
tion
" SPEAKER jacks (14)
# COAXIAL 75Ω FM jack (18)
$ AM terminal (18)
% EURO AV 5 OUTPUT (TO TV) jack (15)
& DMPORT (DIGITAL MEDIA PORT) jack
(16, 69)
' HDMI OUT jack (15)
( TV (DIGITAL IN COAXIAL/OPTICAL)
jacks (15)
Rear panel
CENTER
SUBWOOFER
DIGITAL IN
COAXIAL
OPTICAL
FRONT R
FRONT L
SUR R
SUR L
SPEAKER
T
U
O
I
M
D
H
V
T
SPEAKER
EURO AV
OUTPUT(TO TV)
COAXIAL 75
AM
FM
ANTENNA
DMPORT
DC5V
0.7A MAX
0.7A MAX
HCD-DZ260/DZ270/HDZ278
12
96
GB
About the indications in the front panel display
" Playing status
# Flashes when the sleep timer is set.
(74)
$ Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, decoding mode, etc.
information, radio frequency, playing
status, decoding mode, etc.
% Lights up when a station is received.
(Radio only) (53)
& Stereo/Monaural effect (Radio only)
(54)
' Lights up when the HDMI OUT jack is
correctly connected to HDCP (High-
bandwidth Digital Content Protection)
compliant device with HDMI or DVI
(Digital Visual Interface) input. (15)
bandwidth Digital Content Protection)
compliant device with HDMI or DVI
(Digital Visual Interface) input. (15)
( Current surround format (Except for
JPEG image file)
) Lights up when an NTSC disc is
loaded.
* Lights up during USB recording/
copying. (66)
+ Lights up when Super Audio CD/CD is
loaded. (31)
Front panel display
Click on the first or last page to see other DAV-DZ260 / DAV-DZ270 / HCD-DZ260 / HCD-DZ270 / HCD-HDZ278 service manuals if exist.