DOWNLOAD Sony DAV-DX155 / DAV-DX255 / HCD-DX155 / HCD-DX255 Service Manual ↓ Size: 10.15 MB | Pages: 92 in PDF or view online for FREE

21

2

 stocker section 

1

 Rotate the gear (SS3) in the

     direction of the arrow.

5

 two screws

     (+PTPWH 2.6 

×

 8)

6

 two cams

     (stocker)

8

 cam

     (stocker)

cam (stocker)

cam (stocker)

cam (stocker)

hole

gear
 (stocker 2)

gear
 (stocker 2)

gear
 (stocker 2)

gear (stocker 3)

2

 tension spring (SW)

4

 lever (SW)

1

 screw

     (+PTPWH 2.6 

×

 8)

7

 screw

     (+PTPWH 2.6 

×

 8)

3

 hook

Before installing the cams (stocker), fix the gear (stocker 3) in
the manner so that the hole of the gear (stocker 3) should be
aligned with the hole of the chassis located beneath 
the gear (stocker 3). Be sure to install the cams (stocker) in 
such a way that the grooves of the cams (stocker) face 
the direction of the arrows.

22

1

 screw

     (+PTPWH 2.6 

×

 8)

2

 gear (stocker 3)

gear (stocker 3)
(reverse-side)

rotary encoder
 (ST U/D encoder)

Be sure to align the rib of the gear (stocker 3) with the groove
of the rotary encoder.

groove

rib

1

 three screws

     

(+BTTP 2.6)

2

 rotary encoder (MD)

rotary encoder (MD)

gear (BU2)

cam (BU)

Slide the cam (BU) in the direction of the arrow so that the mark
of the gear (BU2) can be seen. Engage the gears while aligning 
the mark of the gear (BU2) with the protruding part of the 
rotary encoder.

protruding part

mark

23

2

 screw

     (+PTPWH 2.6 

×

 8)

4

 screw

     (+PTPWH 2.6 

×

 8)

6

 screw

     (+PTPWH 2.6 

×

 8)

3

 pulley (BU)

5

 gear (BU1)

7

 gear (BU2)

1

 belt (sub tray)

gear (BU2)

cam (BU)

Before re-assembling, slide the cam (BU) in the direction of 
the arrow. 
Assemble the gear (BU2) in such a manner that the groove
of the cam (BU) is aligned with the rib of the gear (BU2).

rib

groove

24

Regarding the notification symbol “R”
Because the number of the operating buttons of this product
are limited, some operations require use of the operating
buttons of the remote commander, When a specific operation
requires use of the operating buttons of the remote
commander, “R” is added to the specific operating procedure
in this manual. Example  MENU/NO  “R”  The  MENU/NO
button of remote commander.

Incorrect operations may be performed if the test mode is
not entered properly.
In this case, press the  ?/1  button to turn the power off, and
retry to enter the test mode.

The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :

1. Press the  ?/1  button to turn the set on.
2. Press the  FUNCTION  button to set DVD function.
3. Insert a disc.
4. Press the  

x  

button and the  A  button simultaneously for five

seconds.

5. The message “LOCKED” is displayed and the tray is locked.

1. Press the  

x  

button and the  A  button simultaneously for five

seconds again.

2. The message “UNLOCKED” is displayed and the tray is

unlocked.

When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the  ?/1  button.

•

Use this mode when returning the set to the customer after
repair.

1. Press the  ?/1  button to turn the set on.
2. Press the  FUNCTION  button to set the function “DVD”.
3. Remove all discs, and then press two buttons  x  and   .

simultaneously.

4. After a message “MECHA LOCK” is displayed on the

fluorescent indicator tube, pull out the AC plug.

5. To exit from this mode, press the  ?/1  button to turn the set on.

•

A step of AM channels can be changed over between 9 kHz
and 10 kHz.

1. Press the  ?/1  button to turn the set ON.
2. Select the function “TUNER”, and press  FUNCTION  button

to select the BAND “AM”.

3. Press the  ?/1  button to turn the set OFF.
4. Press two buttons  >  and  ?/1  simultaneously, and the

display of fluorescent indicator tube changes to “AM 9 k
STEP” or “AM 10 k STEP”, and thus the channel step is
changed over.

1. Press the  ?/1  button to turn the power on.
2. Press three buttons  . ,  H and  >  simultaneously.
3. The message “VOLUME MAX” is displayed, when the

VOLUME  control is turned in the dirction of (+).
The message “VOLUME MIN” is displayed, when the
VOLUME  control is turned in the dirction of (–).

4. To exit from this mode, press the  ?/1  button to turn the set off.

This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the RAM
to initial conditions. Use this mode when returning the set to the
customer after repair.
Procedure:

1. Press the  ?/1  button to turn the power on.
2. Press the  FUNCTION  button to set the function “DVD”.
3. Remove all discs, and then press three buttons  > ,  A  and

?/1  simultaneously.

4. After the “STANDBY” blinking display finishes, the message

“MECHA LOCK” is displayed on the fluorescent indicator
tube disconnect the AC power plug, then the ship mode is
set.disconnect the AC power plug, then the ship mode is set.

•

The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.

1. Press the  ?/1  button to turn the power on.
2. Press three buttons  x  ,   A  and   ?/1  simultaneously.
3. When this button is operated, display as “COLD RESET” for

a while and all of the settings are reset.

•

This mode is used to check the software version, FL, LED
and KEY.

1. Press the  ?/1  button to turn the power on.
2. Press three buttons  X ,  . and  A  simultaneously.
3. When the display test mode is activated, all segments and LEDs

are turned on.

4. To exit from this mode, press three buttons  X ,  . and  A

simultaneously.

1. When the display test mode is activated, press the  .  button

and the message “DCX1” (DX155), “DCX1D” (DX255) are
displayed, the version test mode is activated.

2. Whenever the  .  button is pressed, the display changes in

the following order.

*1: U2 changes depending on destination.

3. Press the  >  button and the date of the software production

is displayed.

4. Press the  >  button again and the version is displayed.
5. To exit from this mode, press three buttons  X ,  . and  A

simultaneously.

1. When the display test mode is activated, press the  H  button,

to select the key test mode.

2. To enter the KEY test mode, the fluorescent indicator displays

“K0 V0”. Each time a button is pressed, “KEY” value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K8
V0” is displayed.

3. When the  VOLUME  control is turned in the direction of (+),

“V0” is changed to “V1”, then ... “V9”.
When the  VOLUME  control is turned in the direction of (–),
“V0” is changed to “V9”, then ... “V1”.

4. To exit from this mode, press three buttons  X ,  . and  A

simultaneously.

“DCX1” (Model name) t “U2

*1

” (Destination) t MC t SYS 

TM T DSP T TA T ST T CDMB T CDMA T DVD T UI