Sony CX-LDB10 / CX-LDB20 / XR-DB10 / XR-DB20 Service Manual ▷ View online
9
CX-LDB10/LDB20
3-5. MECHANICAL DECK (CMAL5Z220A)
3-6. CONTROL BOARD
2
four screws
(BVTP3
(BVTP3
×
8)
3
coating clip
4
two earth wires
1
wire (flat type)
(7core)
5
plate (shield cassette)
6
mechanical deck (CMAL5Z220A)
8
CONTROL board
2
three screws
(BVTP2.6
(BVTP2.6
×
8)
3
seven screws
(BVTP2.6
(BVTP2.6
×
8)
1
knob (VOL)
4
wire (flat type)
(17core) (CN401)
5
wire (flat type)
(23core) (CN403)
6
wire (flat type)
(7core) (CN404)
7
wire (flat type)
(11core) (CN402)
10
CX-LDB10/LDB20
3-7. MAIN BOARD, POWER TRANSFORMER
3-8. LID (CASSETTE)
2
screw
(BVTP3
(BVTP3
×
8)
3
two sumitite screws
(B3)
(B3)
5
two tapping screws (B3)
9
four screws
7
two claws
8
holder (pwb PT)
6
shield cover
4
MAIN board
1
connector
(13P)(CN902)
q;
power transformer
1
Open the lid cassette.
3
lid cassette
claw
two hooks
2
2
11
CX-LDB10/LDB20
SECTION 4
TEST MODE
COLD RESET
•
The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
Procedure:
1. Press the ?/1 button to turn the set ON.
2. Press three buttons x , ?/1 and [VOLUME] down simulta-
2. Press three buttons x , ?/1 and [VOLUME] down simulta-
neously.
3. The message “RESET” is displayed and the set is reset.
TUNER STEP CHANGE
•
A step of AM channels can be changed over between 9 kHz
and 10 kHz.
and 10 kHz.
Procedure:
1. Press the ?/1 button to turn the set ON.
2. Select the function “TUNER”, and press [TUNER/BAND]
2. Select the function “TUNER”, and press [TUNER/BAND]
button to select the BAND “AM”.
3. Press the ?/1 button to turn the set OFF.
4. Press the > and ?/1 buttons simultaneously, and thus
4. Press the > and ?/1 buttons simultaneously, and thus
the channel step is changed over.
SHIP RESET
Procedure:
1. Press the ?/1 button to turn the set ON.
2. Press the CD u button to select “CD”
3. Remove the disc.
4. The message “NO DISC” is displayed.
5. Press three buttons x , CD u and [VOLUME] down si-
2. Press the CD u button to select “CD”
3. Remove the disc.
4. The message “NO DISC” is displayed.
5. Press three buttons x , CD u and [VOLUME] down si-
multaneously.
6. The message “SHIP RESET” is displayed and the set is reset.
The CD function is activated.
7. To exit from this mode, press the ?/1 button and pull out the
AC plug.
PANEL TEST MODE
•
This mode is used to check the software version, LCD, LED
and keyboard.
and keyboard.
Procedure:
1. Press the ?/1 button to turn the set ON.
2. Press the CD u button to select “CD”
3. Press three bottons [DISPLAY] , ?/1 and [VOLUME] down
2. Press the CD u button to select “CD”
3. Press three bottons [DISPLAY] , ?/1 and [VOLUME] down
simultaneously.
4. When the panel test mode is activated, all segments are turned
on.
VERSION DISPLAY
•
This mode is used check the model, destination, software
version.
version.
Procedure:
1. When the panel test mode is activated, press the button
[BASS/TREBLE], the model and destination are displayed.
KEY TEST MODE
Procedure:
1. When the panel test mode is activated, press the H button,
to select the key test mode.
2. To enter the KEY test mode, the fluorescent indicator displays
“K0 VO”. Each time a button is pressed, “KEY” value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K15
VO” is displayed.
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K15
VO” is displayed.
3. To exit from this mode, pull out the AC plug.
CD Repeat 5 Times Limit Release Mode
Procedure:
1. Press the ?/1 button to turn the set ON.
2. Set the function to “CD”.
3. Press three buttons x , H , and [VOLUME] down simulta-
2. Set the function to “CD”.
3. Press three buttons x , H , and [VOLUME] down simulta-
neously.
4. The repeat all mark blinks and then repeat 5 times limit is
released.
12
CX-LDB10/LDB20
SECTION 5
MECHANICAL ADJUSTMENTS
TAPE MECHANISM DECK SECTION
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads pinch rollers
erase head
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to
4. After the adjustments, apply suitable locking compound to
the parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
Mode
Torque meter
Meter reading
2.94 mN • m to 7.84 mN • m
FWD
CQ-102C
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.14 mN • m to 0.59 mN • m
FWD
CQ-102C
2 to 6 g • cm
back tension
(0.02 – 0.08 oz • inch)
6.86 mN • m to 17.64 mN • m
FF/REW
CQ-201B
71 to 143 g • cm
(0.98 – 1.99 oz • inch)
more than 0.98 N • m
FWD tension
CQ-403A
100 g or more
(3.53 oz or more)
SECTION 6
ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB = 0.775 V
Precaution
1. Demagnetize the record/playback head with a head
demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to
3. After the adjustments, apply suitable locking compound to
the parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit
adjustment should be completed before performing recording
circuit adjustment.)
adjustment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-
CH.
7. Switches and controls should be set as follows unless otherwise
specified.
Test Tape
Tape
Signal
Used for
P-4-A100
10 kHz, –10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Check
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
Output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
Record/Playback Head Azimuth Adjustment
Procedure:
1. Mode: Playback
set
MAIN board
SPEAKER terminal (J302)
L-CH, R-CH
SPEAKER terminal (J302)
L-CH, R-CH
+
–
–
level meter
test tape
P-4-A100
(10 kHz, – 10 dB)
P-4-A100
(10 kHz, – 10 dB)
Click on the first or last page to see other CX-LDB10 / CX-LDB20 / XR-DB10 / XR-DB20 service manuals if exist.