Sony CX-JD5 / JAX-D5 Service Manual ▷ View online
CX-JD5
17
3-16. TABLE ASSY
3
wire (flat type) (5 core)
(CN702)
(CN702)
4
hook
1
Turn the loading gear
in the direction of arrow
in the direction of arrow
A
.
A
5
two claws
2
Pull-out the table assy.
6
table assy
3-17. MOTOR (TB) BOARD
2
tray
4
connector
(CN731)
(CN731)
1
screw
(PTPWH M2.6)
(PTPWH M2.6)
5
two screws
(BTTP M2.6)
(BTTP M2.6)
6
motor (TB) board
3
belt (table)
Ver. 1.2
CX-JD5
18
3-18. MOTOR (LD) BOARD
3-19. RF BOARD
2
two screws
(BTTP M2.6)
(BTTP M2.6)
3
motor (LD) board
1
belt (loading)
3
flexible flat cable
(24 core) (CN001)
(24 core) (CN001)
4
flexible board
(CN003)
(CN003)
1
two screws
(BTTP 2.6)
(BTTP 2.6)
2
RF board
CX-JD5
19
3-20. OPTICAL TRAVERSE UNIT (DBU-1)
7
insulator
2
8
insulator (HRC)
6
insulator
(HRC)
0
holder (DBU) assy
4
step screw (M)
5
step screw (M)
1
floating screw (PTPWH M2.6)
3
step screw (M)
9
optical traverse unit (DBU-1)
20
CX-JD5
SECTION 4
TEST MODE
[MC TEST MODE]
• This mode is used to check operations of the respective sections
of Amplifier, Tuner, and Tape.
Procedure:
* To enter MC Test Mode
1. Press
* To enter MC Test Mode
1. Press
x
button,
[ENTER]
button and
[DISC 3]
button
simultaneously, the message “TEST MODE” will be displayed
on the fluorescent indicator tube.
on the fluorescent indicator tube.
* Check of Amplifier
1. When
1. When
[BASS]
knob is turned clockwise, GEQ increases to its
maximum and a message “GEQ MAX” appears on the
fluorescent indicator tube.
fluorescent indicator tube.
2. When
[BASS]
knob is turned counter clockwise, GEQ
decreases to its minimum and a message “GEQ MIN” appears
on the fluorescent indicator tube.
on the fluorescent indicator tube.
3. When
[SOUND FIELD]
button is pressed, GEQ is set to flat
and a message “GEQ FLAT” appears on the fluorescent
indicator tube.
indicator tube.
4. When the
[VOLUME]
knob is turned clockwise even slightly,
the sound volume increases to its maximum and a message
“VOL MAX” appears for two seconds, then the display returns
to the original display.
“VOL MAX” appears for two seconds, then the display returns
to the original display.
5. When the
[VOLUME]
knob is turned counter-clockwise even
slightly, the sound volume decreases to its minimum and a
message “VOL 0” appears for two seconds, then the display
returns to the original display.
message “VOL 0” appears for two seconds, then the display
returns to the original display.
* VACS ON/OFF Change Over
1. Press
1. Press
[i-Bass]
button. The message “VACS OFF” or “VACS
ON” appears.
* Tape function
1. When a tape is inserted in Deck B and recording is started, the
1. When a tape is inserted in Deck B and recording is started, the
function is changed to VIDEO automatically.
2. After recording is stopped by pressing
x
button, press
–
m
button will change the function to TAPE B and rewind Tape B
until the recording start position and playback of Tape B is
started. If the
until the recording start position and playback of Tape B is
started. If the
[REC PAUSE/ START]
button is pressed for a
pause and pressed again to resume recording during recording
time, when tape deck B is rewind, tape deck B will be rewind
until the position where the pause is applied.
time, when tape deck B is rewind, tape deck B will be rewind
until the position where the pause is applied.
* AMS Test Mode
1. Select the function “TAPE A” or “TAPE B”.
2. Insert a test tape AMS-110A or AMS-120 to selected tape deck.
3. Press the
1. Select the function “TAPE A” or “TAPE B”.
2. Insert a test tape AMS-110A or AMS-120 to selected tape deck.
3. Press the
[CD STNC]
button to enter the AMS test mode.
4. After the test tape is rewind to the beginning of the tape, the
AMS+ is checked, and the mechanism is shut off after detecting
the AMS signal twice.
the AMS signal twice.
5. Then the AMS- is checked and the mechanism is shut off after
detecting the AMS signal twice.
6. When the check is complete, a message of either OK or NG
appears.
* To release MC Test mode.
1. To release this mode, press
1. To release this mode, press
[POWER]
button.
2. The cold reset is enforced at the same time.
[AMP TEST MODE ]
• This mode is used in order to set up each section of amplifier.
Procedure:
1. Press
Procedure:
1. Press
x
button,
[ENTER]
button and
[DISC2]
button
simultaneously, the message “AMP TEST” will be displayed
on the fluorescent indicator tube.
on the fluorescent indicator tube.
2. Press
[ENTER]
button and
[DISC1]
button simultaneously,
VACS display/amplifier regulation display is switched.
3. Press
[SOUND FIELD]
button, SURROUND ON/OFF is
switched.
4. Press
[i-Bass]
button, i-Bass ON/OFF is switched.
5. Turn the
[BASS]
knob, BASS (i-Bass) volume adjustment is
performed.
6. Press
[ENTER]
button, i-Bass f
0
adjustment is performed.
7. To release this mode, pull out the AC cord. Then insert the AC
code, and press
[POWER]
button to turn the set ON. The cold
reset is enforced at the same time.
[PANEL TEST MODE ]
• This mode is used check operation of the front panel.
Procedure:
1. Press
Procedure:
1. Press
X
button,
[ENTER]
button and
[DISC2]
button
simultaneously, all LED and segments in fluorescent indicator
tube are lighted up.
tube are lighted up.
2. Press
[ENTER]
button and
[DISC2]
button simultaneously,
the key check mode is activated. In the key check mode, the
fluorescent indicator tube displays “KEY 0 0 0”. While pressing
the key, the number corresponding to each key is displayed.
Example: When
fluorescent indicator tube displays “KEY 0 0 0”. While pressing
the key, the number corresponding to each key is displayed.
Example: When
[ENTER]
button is pressed “KEY 0 2 0”
3. Press
[ENTER]
button and
[DISC2]
button simultaneously
again, the key control mode is activated. In the key control
mode, the fluorescent indicator tube displays “KEYCONT 0”.
mode, the fluorescent indicator tube displays “KEYCONT 0”.
4. Press
[ENTER]
button and
[DISC2]
button simultaneously
again, “VOLUME FLR” will be displayed.
When the
When the
[VOLUME]
knob is turned clockwise, the message
“VOLUME UP” appears for two seconds, then the message
“VOLUME FLR” is displayed again.
When the
“VOLUME FLR” is displayed again.
When the
[VOLUME]
knob is turned counter-clockwise, the
message “VOLUME DOW” appears for two seconds, then the
message “VOLUME FLR” is displayed again.
message “VOLUME FLR” is displayed again.
5. Press
[ENTER]
button and
[DISC2]
button simultaneously
again, release from this mode.
[VERSION DISPLAY]
• This mode is used check the model, destination, software version.
Procedure:
1. Press
Procedure:
1. Press
X
button,
[ENTER]
button and
[DISC3]
button
simultaneously, the model and destination are displayed.
2. Each time
[ENTER]
button and
[DISC2]
button is pressed
simultaneously, the display changes from MC version, GC
version and DVD version in this order, and release from this
mode.
version and DVD version in this order, and release from this
mode.
3. When
[ENTER]
button and
[DISC2]
button is pressed
simultaneously while the version numbers are being displayed
except model and destination, the date of the software creation
appear. When
except model and destination, the date of the software creation
appear. When
[ENTER]
button and
[DISC2]
button is pressed
simultaneously again, the display returns to the software
version display.
version display.
[COLD RESET]
• The cold reset clears all data stored in the RAM to initial condi-
tions. Execute this mode when returning the set to the customer.
Procedure:
1. Press
1. Press
x
button,
[ENTER]
button, and
[DISC1]
button
simultaneously.
2. The fluorescent indicator tube becomes blank for a while, and
the set is reset.
Click on the first or last page to see other CX-JD5 / JAX-D5 service manuals if exist.