Sony CMT-VC1 / HCD-VC1 Service Manual ▷ View online
2
HCD-VC1
TABLE OF CONTENTS
1.
GENERAL
Parts Identification ..........................................................
4
Setting the Time ..............................................................
5
2.
DISASSEMBLY
2-1. Disassembly Flow ...........................................................
7
2-2. Upper Cover Sub Assy ....................................................
8
2-3. CD Lid .............................................................................
8
2-4. Front Panel Section .........................................................
9
2-5. Mech Deck (Tape) ...........................................................
9
2-6. CD Mechanism Deck (CDM55F-K6BD42A),
MPEG Board ................................................................... 10
2-7. Base Unit (BU-K6BD42A) ............................................. 10
2-8. Loading Board ................................................................. 11
2-9. Cam (CDM55) ................................................................ 11
2-8. Loading Board ................................................................. 11
2-9. Cam (CDM55) ................................................................ 11
3.
TEST MODE
.............................................................. 12
4.
ELECTRICAL ADJUSTMENTS
Deck Section ................................................................... 13
CD Section ...................................................................... 13
CD Section ...................................................................... 13
5.
DIAGRAMS
5-1. Block Diagram – CD SERVO Section – ....................... 14
5-2. Block Diagram – MAIN Section – ................................ 15
5-3. Block Diagram
5-2. Block Diagram – MAIN Section – ................................ 15
5-3. Block Diagram
– DISPLAY/POWER SUPPLY Section – ...................... 16
5-4. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 17
5-5. Printed Wiring Board – CD Board – ............................. 18
5-6. Schematic Diagram – CD Board – ................................ 19
5-7. Printed Wiring Board – TC Board – .............................. 20
5-8. Schematic Diagram – TC Board – ................................. 21
5-9. Schematic Diagram – MAIN Board (1/2) – .................. 22
5-10. Schematic Diagram – MAIN Board (2/2) – .................. 23
5-11. Printed Wiring Board – MAIN Board – ........................ 24
5-12. Printed Wiring Boards
5-6. Schematic Diagram – CD Board – ................................ 19
5-7. Printed Wiring Board – TC Board – .............................. 20
5-8. Schematic Diagram – TC Board – ................................. 21
5-9. Schematic Diagram – MAIN Board (1/2) – .................. 22
5-10. Schematic Diagram – MAIN Board (2/2) – .................. 23
5-11. Printed Wiring Board – MAIN Board – ........................ 24
5-12. Printed Wiring Boards
– SWITCH/I/O SWITCH Boards – ................................ 26
5-13. Schematic Diagram
– SWITCH/I/O SWITCH Boards – ................................ 27
5-14. IC Pin Function Description ........................................... 28
5-15. Printed Wiring Boards – HEADPHONE/
5-15. Printed Wiring Boards – HEADPHONE/
LCD/LOADING /VIDEO Boards – ............................... 29
5-16. Schematic Diagram – HEADPHONE/
LCD/LOADING /VIDEO Boards – ............................... 29
5-17. Printed Wiring Board – POWER Board – ..................... 30
5-18. Schematic Diagram – POWER Board – ........................ 31
5-18. Schematic Diagram – POWER Board – ........................ 31
6.
EXPLODED VIEWS
6-1. Upper Cover, Tape Mech Deck Section ......................... 34
6-2. Front Panel Section ......................................................... 35
6-3. Chassis Section ............................................................... 36
6-4. CD Mechanism Deck (CDM55F-K6BD42A) ................ 37
6-5. Base Unit (BU-K6BD42A) ............................................. 38
6-2. Front Panel Section ......................................................... 35
6-3. Chassis Section ............................................................... 36
6-4. CD Mechanism Deck (CDM55F-K6BD42A) ................ 37
6-5. Base Unit (BU-K6BD42A) ............................................. 38
7.
ELECTRICAL PARTS LIST
............................... 39
General
Power requirements
110 - 120 V or 220 -
240 V AC , 50/60 Hz
Adjustable with voltage
selector
240 V AC , 50/60 Hz
Adjustable with voltage
selector
Power consumption
75 W
Dimensions (w/h/d)
Approx. 191
×
253
×
346 mm incl. projecting
parts and controls
parts and controls
Mass
Approx. 5.6 kg
Design and specifications are subject to change
without notice.
without notice.
3
HCD-VC1
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
The following caution label is located inside the unit.
CAUTION
:
INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL :
USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE
FOR STRÅLING.
FOR STRÅLING.
VORSICHT :
UNSICHTBARE LASERSTRAHLUNG, WENN
ABDECKUNG GEÖFFNET UND SICHEREITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
VARO
!
:
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALT-
TIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING
:
OSYNLING LASERSTRÅLING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
ADVERSEL :
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
VIGYAZAT
!
:
A BURKOLAT NYITÁSAKOR LÁTHATATLAN LÉZERSU-
GÁRVESZÉLY
!
KERÜLJE A BESUGÁRZÁST
!
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
SERVICE POSITION
In checking the CD block, prepare jig (extension cable J-2501-
011-B).
011-B).
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
Connect jig (extension cable J-2501-011-B)
to the MAIN board (CN101) and VCD block (CN502).
to the MAIN board (CN101) and VCD block (CN502).
MAIN board
VCD block
4
HCD-VC1
SECTION 1
GENERAL
– Front View –
Parts Identification
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses () for details.
Main unit
This section is extracted from
instruction manual.
instruction manual.
4
CD cover qa (9, 21)
Shown open in the illustration
above.
above.
CD SYNC 9 (16, 17)
CD u qk (9-13, 26)
CD x qj (9-13, 24)
CD .m/M> qh (10,
CD u qk (9-13, 26)
CD x qj (9-13, 24)
CD .m/M> qh (10,
11)
CD Z qg (9-11)
DSG indicator qd (19)
FUNCTION 7 (9, 11, 12, 14-16,
DSG indicator qd (19)
FUNCTION 7 (9, 11, 12, 14-16,
21, 24)
PBC indicator qf (10, 26)
PHONES jack qs (21)
Remote sensor q;
TAPE PAUSE X 5 (15-17)
TAPE Y 2 (15-17)
TAPE x 3 (15-17, 24)
TAPE m/M 4 (15)
TUNER/BAND w; (14, 24)
VOLUME 8 (20)
PHONES jack qs (21)
Remote sensor q;
TAPE PAUSE X 5 (15-17)
TAPE Y 2 (15-17)
TAPE x 3 (15-17, 24)
TAPE m/M 4 (15)
TUNER/BAND w; (14, 24)
VOLUME 8 (20)
BUTTON DESCRIPTIONS
@/1 (power) 1 (7, 14, 18, 20, 21)
Z 6 (15)
+/— ql (14)
Z 6 (15)
+/— ql (14)
1 2
5
4
7
6
3
8
9
q;
qs
qg
qd
qj
qh
qk
ql
w;
qa
qf
5
HCD-VC1
– Rear View –
1 AM ANTENNA terminals
2 AUDIO IN MD (VIDEO) jacks
3 CD DIGITAL OUT OPTICAL connector
4 SPEAKER terminals
5 SYSTEM SELECT switch
6 VIDEO OUT jack
7 VOLTAGE SELECTOR switch
8 AC power cord
2
1
5
6
7
8
3
4
Setting the time
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
If you are setting the clock for the first time,
go to step 5.
go to step 5.
3
Press +/— on the remote repeatedly
until SET CLOCK appears in the
display.
until SET CLOCK appears in the
display.
4
Press ENTER on the remote.
The hour indication flashes.
5
Press +/— on the remote repeatedly to
set the hour.
set the hour.
6
Press ENTER on the remote.
The minute indication flashes.
7
Press +/— on the remote repeatedly to
set the minute.
set the minute.
8
Press ENTER on the remote.
The clock will begin operating.
To reset the system clock
Start over from step 1.