Sony CMT-SX2D / HCD-SX2D Service Manual ▷ View online
9
HCD-SX2D
Use buttons on the remote for the operation.
1
Press
?/1
to turn on the system.
2
Press CLOCK/TIMER SET.
3
Press
.
or
>
repeatedly to set the
hour.
4
Press ENTER.
5
Press
.
or
>
repeatedly to set the
minute.
6
Press ENTER.
The clock starts working.
To adjust the clock
1
Press CLOCK/TIMER SET.
2
Press
.
or
>
to select “CLOCK SET,”
then press ENTER.
3
Do the same procedures as step 3 to 6
above.
above.
Notes
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
You cannot set the clock in Power Saving Mode
(page 37).
Setting the clock
10
HCD-SX2D
SECTION 3
DISASSEMBLY
3-1. DISASSEMBLY FLOW
• This set can be disassembled in the order shown below.
3-2. TOP COVER, DC FAN
(Page 11)
SET
3-3. AMP BOARD, AV BOARD,
TUNER (FM/AM)
(Page 11)
3-5. MPEG HOLDER
(Page 12)
3-4. MPEG BOARD
(Page 12)
3-6. PANEL (DVD)
(Page 13)
3-8. FRONT PANEL SECTION
(Page 14)
3-12. MAIN BOARD
(Page 16)
3-13. POWER BOARD
(Page 16)
3-14. PANEL CASS (CASSETTE)
(Page 17)
3-7. DVD LOADER
(DVD MECHANISM)
(Page 13)
3-10. KEY BOARD
(Page 15)
3-11. HP BOARD,
MIC BOARD
(Page 15)
3-9. CASSETTE MECHANISM DECK
(CMAL5Z220C)
(Page 14)
Ver. 1.1
11
HCD-SX2D
Note:
Follow the disassembly procedure in the numerical order given.
3-2. TOP COVER, DC FAN
3
screw
(screw 3
×
8)
9
screw
(screw 3
×
8)
qa
four screws
(screw 3
×
8)
8
two screws
(screw 3
×
8)
0
connector
3P (CN350)
6
qs
DC fan
qd
cover heat sink
b
7
top cover
1
screw
(screw 3
×
8)
5
five screws
(screw 3
×
8)
a
a
b
4
screw
(screw 3
×
10)
2
screw
(screw 3
×
10)
1
two screws
(screw 3
×
10)
qf
four screws
(screw 3
×
10)
qa
screw
(screw 3
×
8)
9
three screws
(screw 3
×
10)
8
two screws
(screw 3
×
8)
0
two screws
(screw 3
×
8)
qh
two screws
(screw 3
×
8)
2
two screws
(screw 3
×
10)
7
AMP board
3
connector
10P (CN108)
4
connector
7P (CN102)
5
connector
3P (CN106)
6
connector
5P (CN101)
qd
wire (flat type)
16core (CN801A)
qs
earth wire
qg
AV board
qk
tuner
w;
panel rear
ql
two claws
qj
wire (flat type)
9core
3-3. AMP BOARD, AV BOARD, TUNER (FM/AM)
12
HCD-SX2D
3-5. MPEG HOLDER
3-4. MPEG BOARD
8
MPEG board
3
wire (flat type)
24core (CN7)
6
wire (flat type)
12core (CN1)
5
connector
9P (CN3)
2
connector
5P (CN9)
1
connector
6P (CN10)
7
two screws
(screw 3
×
8)
4
wire (flat type)
16core (CN2)
1
screw
(screw 3
×
8)
3
MPEG holder
6
holder
2
two hooks
4
two screws
(screw 3
×
8)
5
two screws
(screw 3
×
8)
Click on the first or last page to see other CMT-SX2D / HCD-SX2D service manuals if exist.