DOWNLOAD Sony CMT-PX333 / HCD-PX333 Service Manual ↓ Size: 14 MB | Pages: 110 in PDF or view online for FREE

Model
CMT-PX333 HCD-PX333
Pages
110
Size
14 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
cmt-px333-hcd-px333.pdf
Date

Sony CMT-PX333 / HCD-PX333 Service Manual ▷ View online

5
HCD-PX333
CD SECTION
PROCEDURE FOR USING THE SELF-DIAGNOSIS FUNC-
TION (ERROR HISTORY DISPLAY MODE)
1. To Enter The CD Test Mode
Procedure:
1. Press the
?
/1
button to turn the power on.
2. Press the [FUNCTION] button to set the CD function.
3. Press three buttons of
 (CD), 
[             TUNING-]
 and
[TUNER/BAND]
 simultaneously.
4. The set enter the CD test mode (menu) and displays “dvt ERR
CODE”.
Note:
If the consequence was displayed except “dvt ERR CODE”, press the
[               TUNING-]
,  
[                TUNING+]
button to display “dvt
ERR CODE”.
2. Display of Error Number
Procedure:
1. Press the
Z
(CD) button to display as bellow.
(a) Number of mechanical error.
(b) Number of no disc error that occurred after chucking.
2. Press the
x
(CD) button and return to CD test mode menu
(“dvt ERR CODE” is displayed).
3. Display of Mechanical Error History
Procedure:
1. In the CD test mode menu, press the 
[            TUNING-]
,
[            TUNING+]
button to display “dvt ECODE MEC”.
2. Press the
Z
(CD) button to display as bellow.
(a) The number of mechanical error.
Latest one “00” to last ten “09”
(Press the 
[             TUNING-]
,
[            TUNING+]
 button to
change the error number)
(b) FF: Mechanical error, when normal operation.
Other display: Mechanical error, between mechanical initialize.
(c), (d), (e): Not used in servicing.
3. Press the
x
(CD) button and return to CD test mode menu
(“dvt ECODE MEC” is displayed).
Display
Emc=**Edc=**
(a)
(b)
.m
Display
E**M********00
(c)
(a)
(b)
(d) (e)
4. Display of No Disc Error History
Procedure:
1. In the CD test mode menu, press the 
[           TUNING-]
,
[            TUNING+]
 button to display “dvt ECODE BU”.
2. Press the
Z
(CD) button to display as bellow.
(a) The number of no disc error.
Latest one “00” to last ten “09”
(Press the 
[            TUNING-]
 or  
[            TUNING+]
 button to
change the error number)
(b) 01: Focus error
02: GFS error
03: Set up error
04: Focus error (not used in servicing)
(c) 00:No disc error (Did not chucking retry)
02: No disc error (Chucking retry to completion)
(d) The status, when determined no disc error.
2x: During setting up
3x: During reading TOC
4x: During accessing
5x: During playback
6x: During pause
7x: During manual search (during playback)
8x: During manual search (during pause)
3. Press the
x
(CD) button and return to CD test mode menu
(“dvt ECODE BU” is displayed).
4. To Erase The Error History
When returning the unit to the customer after completing repairs,
perform this to erase the past error history.
Procedure:
1. In the CD test mode menu, press the 
[            TUNING-]
,
[             TUNING+]
 button to display “dvt ECNT0 MEC”. (When
erase the mechanical error)
Or one more press the 
[          TUNING+]
 button to display
“dvt ECNT0 BU”. (When erase the no disc error)
2. Press the
Z
(CD) button to erase the error history (mechanical
error or no disc error) and display as bellow.
5. To Release The CD Test Mode
Press the
?
/1
button to turn the power off.
Display
E**D********
(c)
(a)
(b)
(d) (e)
Display
Emc=00Edc=00
.m
M>
.m
M>
.m
M>
.m
M>
.m
M>
.m
M>
M>
6
HCD-PX333
TABLE  OF  CONTENTS
SELF-DIAGNOSIS FUNCTION
.....................................
2
1.
SERVICING  NOTES
...............................................
7
2.
GENERAL
................................................................... 17
3.
DISASSEMBLY
......................................................... 19
4.
TEST MODE
............................................................... 31
5.
ELECTRICAL  ADJUSTMENTS
MD Section ..................................................................... 37
CD Section ...................................................................... 48
6.
DIAGRAMS
6-1. Block Diagram – MD Servo Section – ........................... 51
– D/A, A/D Converter Section – ..................................... 52
– Main Section ................................................................ 53
– Display, Power Supply Section – ................................ 54
6-2. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 55
6-3. Printed Wiring Board – BD (CD) Board – ..................... 56
6-4. Schematic Diagram – BD (CD) Board – ........................ 57
6-5. Printed Wiring Board – BD (MD) Board – .................... 58
6-6. Schematic Diagram – BD (MD) Board (1/2) – .............. 59
6-7. Schematic Diagram – BD (MD) Board (2/2) – .............. 60
6-8. Printed Wiring Board – MD DIGITAL Section – .......... 61
6-9. Schematic Diagram – MD Digital Section (1/3) – ......... 62
6-10. Schematic Diagram – MD Digital Section (2/3) – ......... 63
6-11. Schematic Diagram – MD Digital Section (3/3) – ......... 64
6-12. Printed Wiring Boards  – Main Board – ......................... 65
6-13. Schematic Diagram – Main Board (1/2) – ..................... 66
6-14. Schematic Diagram – Main Board (1/2) – ..................... 67
6-15. Printed Wiring Board  – AMP Board – .......................... 68
6-16. Printed Wiring Board  – SP Board – .............................. 68
6-17. Schematic Diagram  – AMP Board – ............................. 69
6-18. Schematic Diagram – SP Board – .................................. 70
6-19. Printed Wiring Boards  – Panel Section1 – .................... 71
6-20. Schematic Diagram  – Panel Section1 – ........................ 72
6-21. Printed Wiring Boards  – Panel Section2 – .................... 73
6-22. Schematic Diagram  – Panel Section2 – ........................ 73
6-23. Printed Wiring Boards  – Power Board – ....................... 74
6-24. Schematic Diagram  – Power Board – ........................... 75
6-25. IC Block Diagrams .......................................................... 77
6-26. IC Pin Function Description ........................................... 81
7.
EXPLODED  VIEWS
................................................ 93
8.
ELECTRICAL  PARTS  LIST
.............................. 100
MODEL IDENTIFICATION
— Back panel —
Model
Part No.
AEP,UK models
4-231-958-1[]
Homg Kong,Malaysia,
Singapore models
4-231-958-2[]
Australian model
4-231-958-3[]
PART No.
7
HCD-PX333
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
For CD
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
For MD
NOTES  ON  LASER  DIODE  EMISSION  CHECK
Never look into the laser diode emission from right above when
checking it for adjustment. It is feared that you will lose your sight.
NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
The following caution label is located inside the unit.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
SECTION  1
SERVICING  NOTES
(Figure A)
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende type
anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til fabrikantens
instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ som
 rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande föreskrifter.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
CLEANING  OBJECTIVE  LENS  OF  OPTICAL  PICK-UP
• In cleaning the objective lens of optical pick-up, be sure the
following below.
1. In cleaning the lens, do not apply an excessive force.
As the optical pick-up is vulnerable, application of excessive
force could damage the lens holder.
2. In cleaning, do not use a cleaner other than exclusive cleaning
liquid (KK-91 or isopropyl alcohol).
3. Wipe the objective lens spirally from center toward outside. (See
Figure A)
4. Eject the disk, if loaded.
5. Disconnect the power cord from the socket to shut off the power
supply.
6. When cleaning the objective lens of optical pick-up in CD, refer
to  “HOLDER (BU) ASS’Y” on page XX for removing
HOLDER (BU) ASS’Y.
8
HCD-PX333
SERVICE  POSITION
• In checking the MD mechanism deck section (MDM-7X2A), prepare two extension jigs (Part No. J-2501-100-A: 1.00 mm 27 core and
Part No. J-2501-198-A: 1.00 mm 17 core).
• In checking the CD mechanism deck section (CDM55A-21BD53), prepare extension jig (Part No. J-2501-075-A: 1.00 mm 21 core.)
MD mechanism deck section
(MDM-7X2A)
CN103
BD (MD) board
CD mechanism deck section
(CDM55A-21BD53)
Connect extension jig (J-2501-198-A) to the
BD (MD) board (CN103) and MD DIGITAL board (CN1004).
Connect extension jig (J-2501-100-A) to the
BD (MD) board (CN102) and MD DIGITAL board (CN1003).
CN1004
CN1003
CN101
BD (CD) board
CN1005
CN1002
MD DIGITAL board
Connect extension jig (J-2501-075-A) 
to the BD (CD) board (CN101) and 
MD DIGITAL board (CN1002).
CN1005
Pin 
2
 (GND)
Pin 
3
 (OUTSW)
CN102
harness
Note on Checking CD Mechanism Deck Section
In performing the operation check with the CD mechanism deck section removed from the main unit, the CD disc loading will be disabled if
the connector cable between MD DIGITAL board (CN1005) and LOADING board (CN151) is disconnected. Accordingly, make preparation
through the following steps.
1. Insert the CD disc for test with the set assembled.
2. Unplug the AC power cord to turn the power off, and remove the CD mechanism deck section. (Disconnect the connector cable between
MD DIGITAL board (CN1005) and LOADING board (CN151), and also the connector cable between MD DIGITAL board (CN1002)
and BD (CD) board (CN101))
3. Connect the CN1005 pin 3 (OUTSW) and pin 2 (GND) on the MD DIGITAL board with a lead wire.
4. Connect the connectors between MD DIGITAL board (CN1002) and BD (CD) board (CN101) with the extension tool (part No.: J-2501-
075-A).
Note 1:
Under this condition, the CD can be played but the disc loading operation is disabled.
Note 2:
After checking, disconnect the lead wire connected in step 3.
Page of 110
Display

Click on the first or last page to see other CMT-PX333 / HCD-PX333 service manuals if exist.