Sony CMT-NE5 / HCD-NE5 Service Manual ▷ View online
5
HCD-NE5
SERVICE POSITION
– CD board –
– CD board –
– TCM block –
– AMP board –
TCM block
AMP board
CD board
6
HCD-NE5
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
• LOCATION OF CONTROLS
Main unit
ALBUM +/
−
7 (10, 11)
BASS/TREBLE 8 (17)
Cassette compartment qf
CD SYNCHRO qg (16)
DISPLAY 0 (14, 20)
Display window 5
DSGX 9 (17)
Cassette compartment qf
CD SYNCHRO qg (16)
DISPLAY 0 (14, 20)
Display window 5
DSGX 9 (17)
PHONES jack qk
PLAY MODE qj
Remote sensor 2
TUNER/BAND qs
TUNING +/
PLAY MODE qj
Remote sensor 2
TUNER/BAND qs
TUNING +/
−
4
TUNING MODE qj
VOLUME qa
VOLUME qa
?/1 (power) 1
.m/M> (skip back/
.m/M> (skip back/
skip forward, rewind/fast
forward) 4
forward) 4
x (stop) 3
z REC PAUSE/START qh
CD/NX (play/pause) ql
TAPE/N (play) w;
Z PUSH OPEN/CLOSE (CD
z REC PAUSE/START qh
CD/NX (play/pause) ql
TAPE/N (play) w;
Z PUSH OPEN/CLOSE (CD
open/close) 6
Z PUSH OPEN (tape open/close)
qd
ALPHABETICAL ORDER
A - O
P - Z
BUTTON DESCRIPTIONS
1 2 3 4 5
6
7
8
9
0
qs
qa
qd
qf
qg
qh
qj
qk
w;
ql
Remote control
ALBUM +/
−
qa
CD qh
CLEAR qd
CLOCK/TIMER SELECT 2
CLOCK/TIMER SET 3
DISPLAY ql
ENTER 9
EQ qs
FM MODE 4
FUNCTION 6
CLEAR qd
CLOCK/TIMER SELECT 2
CLOCK/TIMER SET 3
DISPLAY ql
ENTER 9
EQ qs
FM MODE 4
FUNCTION 6
PLAY MODE qk
REPEAT 4
SLEEP w;
TAPE qg
TUNER/BAND 5
TUNER MEMORY qj
TUNING MODE qk
VOLUME +/
REPEAT 4
SLEEP w;
TAPE qg
TUNER/BAND 5
TUNER MEMORY qj
TUNING MODE qk
VOLUME +/
−
0
?/1 (power) 1
m/M (rewind/fast forward)
m/M (rewind/fast forward)
7
./> (go back/go forward)
qf
x (stop) 8
X (pause) 8
N (play) 8
+/
X (pause) 8
N (play) 8
+/
−
(tuning) qf
ALPHABETICAL ORDER
A - O
P - Z
BUTTON DESCRIPTIONS
4
5
6
7
8
9
w;
1
qa
qd
qs
ql
qk
qj
qh
qg
qf
0
3
2
Use buttons on the remote for the operation.
1
Press
?/1
to turn on the system.
2
Press CLOCK/TIMER SET.
3
Press
./>
repeatedly to set the
hour.
4
Press ENTER.
5
Press
./>
repeatedly to set the
minute.
6
Press ENTER.
The clock starts working.
To adjust the clock
1
Press CLOCK/TIMER SET.
2
Press
./>
until CLOCK appears,
then press ENTER.
3
Do the same procedures as step 3 to 6
above.
above.
Note
The clock is not displayed in Power Saving Mode.
Setting the clock
HCD-NE5
7
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. REAR CABINET
(Page 7)
3-6. MECHANICAL DECK
(Page 9)
3-7. MAIN BOARD
(Page 10)
3-4. FRONT PANEL ASSY
(Page 8)
3-5. BASE UNIT
(BU-K7BD81B)
(Page 9)
(Page 9)
3-3. TOP PANEL ASSY
(Page 8)
SET
3-8. AMP BOARD
(Page 10)
3-2.
REAR CABINET
2
four screws
(BTP3
(BTP3
×
12)
7
connector
(CN310)
(CN310)
6
8
rear cabinet
5
two screws
(BVTP3
(BVTP3
×
10)
1
four screws
(BTP3
(BTP3
×
12)
3
two screws
(BVTP3
(BVTP3
×
10)
4
five screws
(BVTP3
(BVTP3
×
10)
HCD-NE5
8
3-4.
FRONT PANEL ASSY
1
claw
3
5
connector
(S820)
(S820)
4
wire (flat type) (27 core)
(CN305)
(CN305)
2
claw
6
top panel assy
1
wire (flat type) (24 core)
(CN302)
(CN302)
qa
flont panel assy
2
wire (flat type) (16 core)
(CN303)
(CN303)
q;
wire (flat type) (15 core)
6
two screws
(BVTP3
(BVTP3
×
10)
9
7
8
5
connector
(CN301)
(CN301)
4
connector
(CN501)
(CN501)
3
connector
(CN501B)
(CN501B)
3-3.
TOP PANEL ASSY
Click on the first or last page to see other CMT-NE5 / HCD-NE5 service manuals if exist.