Sony CMT-NE3 / HCD-NE3 Service Manual ▷ View online
5
HCD-NE3
SERVICE POSITION
– BD board –
– BD board –
– TCM block –
– AMP board –
TCM block
AMP board
BD board
6
HCD-NE3
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
•
LOCATION OF CONTROLS
Main unit
BASS/TREBLE 8
Cassette compartment qf
CD SYNCHRO qg
DISPLAY 0
Displaywindow 5
DSGX 9
Cassette compartment qf
CD SYNCHRO qg
DISPLAY 0
Displaywindow 5
DSGX 9
PHONES jack qk
PLAY MODE qj
Remote sensor 2
TUNER/BAND qs
TUNING +/
PLAY MODE qj
Remote sensor 2
TUNER/BAND qs
TUNING +/
−
4
TUNING MODE qj
VOLUME qa
VOLUME qa
?/1 (power) 1
.m/M> (skip back/
.m/M> (skip back/
skip forward,rewind/fast
forward) 4
forward) 4
x (stop) 3
z RECPAUSE/START qh
CD/NX(play/pause) ql
TAPE/N(play) w;
Z PUSHOPEN/CLOSE (CD
z RECPAUSE/START qh
CD/NX(play/pause) ql
TAPE/N(play) w;
Z PUSHOPEN/CLOSE (CD
open/close) 6
Z PUSHOPEN (tape open/close)
qd
ALPHABETICAL ORDER
A – O
P – Z
BUTTON DESCRIPTIONS
1 2 3 4 5
6
8
9
0
qs
qa
qd
qf
qg
qh
qj
qk
w;
ql
7
HCD-NE3
Use buttons on the remote for the operation.
1
Press
?/1
to turn on the system.
2
Press CLOCK/TIMER SET.
3
Press
./>
repeatedly to set the
hour.
4
Press ENTER.
5
Press
./>
repeatedly to set the
minute.
6
Press ENTER.
The clock starts working.
To adjust the clock
1
Press CLOCK/TIMER SET.
2
Press
./>
until “CLOCK” appears,
then press ENTER.
3
Do the same procedures as step 3 to 6
above.
above.
Note
The clock is not displayed in Power Saving Mode.
Setting the clock
Remote control
CD qh
CLEAR qd
CLOCK/TIMER SELECT 2
CLOCK/TIMERS ET 3
DISPLAY ql
ENTER 9
EQ qs
FM MODE 4
FUNCTION 6
CLEAR qd
CLOCK/TIMER SELECT 2
CLOCK/TIMERS ET 3
DISPLAY ql
ENTER 9
EQ qs
FM MODE 4
FUNCTION 6
PLAY MODE qk
REPEAT 4
SLEEP w;
TAPE qg
TUNER/BAND 5
TUNER MEMORY qj
TUNING MODE qk
VOLUME +/
REPEAT 4
SLEEP w;
TAPE qg
TUNER/BAND 5
TUNER MEMORY qj
TUNING MODE qk
VOLUME +/
− 0
?/1 (power) 1
m/M (rewind/fast forward)
m/M (rewind/fast forward)
7
./> (go back/go forward)
qf
x (stop) 8
X (pause) 8
N (play) 8
+/
X (pause) 8
N (play) 8
+/
− (tuning) qf
ALPHABETICAL ORDER
A – O
P – Z
BUTTON DESCRIPTIONS
4
5
6
7
8
9
w;
1
qd
qs
ql
qk
qj
qh
qg
qf
0
3
2
CMT-NE3
* Button does not function with this model.
*
HCD-NE3
8
•
This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. REAR CABINET
(Page 8)
3-6. MECHANICAL DECK
(Page 10)
3-7. MAIN BOARD
(Page 11)
3-4. FRONT PANEL ASSY
(Page 9)
3-5. BASE UNIT
(BU-K7BD80B)
(Page 10)
(Page 10)
3-3. TOP PANEL ASSY
(Page 9)
SET
3-8. AMP BOARD
(Page 11)
Note:
Follow the disassembly procedure in the numerical order given.
3-2.
REAR CABINET
2
four screws
(BVTP3
(BVTP3
×
8)
7
rear cabinet
5
two screws
(BVTP3
(BVTP3
×
10)
6
two screws
(BVTP3
(BVTP3
×
10)
1
four screws
(BVTP3
(BVTP3
×
8)
3
two screws
(BVTP3
(BVTP3
×
10)
4
five screws
(BVTP3
(BVTP3
×
10)
Click on the first or last page to see other CMT-NE3 / HCD-NE3 service manuals if exist.