Sony CMT-M373NT / HCD-M373 Service Manual ▷ View online
4
HCD-M373
This system has a Self-diagnosis display
function to let you know if there is a system
malfunction. The display shows a code made up
of three or five letters and a message alternately
to show you the problem. To solve the problem
refer to the following list. If any problem
persists, consult your nearest Sony dealer.
function to let you know if there is a system
malfunction. The display shows a code made up
of three or five letters and a message alternately
to show you the problem. To solve the problem
refer to the following list. If any problem
persists, consult your nearest Sony dealer.
C11/Protected
The MD is protected against erasure.
c Remove the MD and slide the tab to close the slot
(page 15).
C12/Cannot Copy
You tried to record a CD with a format that the
system does not support, such as a CD-ROM.
system does not support, such as a CD-ROM.
c Remove the disc and turn off the system once,
then turn it on again.
C13/REC Error
Recording could not be performed properly.
c Move the system to a stable place, and start
recording over from the beginning.
The MD is dirty or scratched, or the MD does not
meet the standards.
meet the standards.
c Replace the MD and start recording over from the
beginning.
C13/Read Error
The MD deck cannot read the disc information
properly.
properly.
c Remove the MD once, then insert it again.
C14/TOC Error
The MD deck cannot read the disc information
properly.
properly.
c Replace the MD.
c Erase all the recorded contents of the MD using
the All Erase Function (page 29).
Self-diagnosis display
C41/Cannot Copy
The sound source is a copy of a commercially
available music software or CD-R.
available music software or CD-R.
cThe Serial Copy Management System prevents
making a digital copy (page 64). In addition, you
cannot copy from a CD-R.
cannot copy from a CD-R.
C71/Check OPT-IN
No component is connected to the DIGITAL
OPTICAL IN jack, or you tried to record from th e
digital component which is not connected correctly.
OPTICAL IN jack, or you tried to record from th e
digital component which is not connected correctly.
cConnect the optional digital component correctly
to the DIGITAL OPTICAL IN jack using the
digital optical cable (not supplied) (page 52).
digital optical cable (not supplied) (page 52).
The power of the connected component is not turned
on.
on.
cCheck if the power of the connected digital
component is on. Refer to the operating
instructions supplied with the component.
instructions supplied with the component.
The digital optical cable is disconnected, or the
power of the connected component is turned off
while recording the digital audio from the
component connected to the DIGITAL OPTICAL
IN jack.
power of the connected component is turned off
while recording the digital audio from the
component connected to the DIGITAL OPTICAL
IN jack.
cConnect the digital optical cable, or turn on the
power of the connected component.
E0001/MEMORY NG
The component has internal problem.
cConsult your nearest Sony dealer.
E0101/LASER NG
There is a problem with the laser pickup.
cThe laser pickup may be damaged. Consult your
nearest Sony dealer.
E0201/LOADING NG
There is a problem with loading.
cConsult your nearest Sony dealer.
5
HCD-M373
One of the following messages may appear or
flash in the display during operation.
flash in the display during operation.
CD
Cannot Edit
You tried to label a CD-TEXT di sc.
CD No Disc
There is no disc in the player.
Name Full
There are already 50 disc titles stored in the system.
OVER
You have reached the end of the disc while pressing
M during playback or pause.
M during playback or pause.
Step Full!
You tried to program 26 or more tracks (steps).
MD
Assign None
All the tracks on an MD are registered into groups.
Auto Cut
The MD deck is pausing the recording because
silence continued for 30 seconds or more during
digital recording.
silence continued for 30 seconds or more during
digital recording.
Blank Disc
The inserted recordable MD is new, or all tracks on
the MD have been erased.
the MD have been erased.
Cannot Edit
• A pre-mastered MD is in the deck.
• You tried to edit in Program or Shuffle Play mode.
• The track is recorded in MDLP mode.
Cannot REC
• A pre-mastered MD is in the deck.
• The function is switched to MD or PC.
Cannot SYNC!
• There is no disc in the MD deck, or the MD is
protected against erasure.
• There is no time remaining on the MD.
Complete!
The editing operation of the MD is completed.
Disc Full!
There is no time remaining on the MD.
Eject
The MD deck is ejecting the MD.
Messages
Group Full!
An attempt was made to create a new group in
excess of the maximum number of groups, or there
are insufficient characters for updating the group
management information.
excess of the maximum number of groups, or there
are insufficient characters for updating the group
management information.
Impossible
• You tried to make an impossible editing
operation.
• You cannot perform Net MD operations during
timer playback.
• You cannot combine or erase the tracks due to the
system limitations of MDs.
Incomplete!
Adjustment of the recording level after recording or
Fade-in and Fade-out procedures have failed since
the system was either subject to vibration or there is
a damaged or dirty disc in the tray.
Fade-in and Fade-out procedures have failed since
the system was either subject to vibration or there is
a damaged or dirty disc in the tray.
Initialize
The power was off for a long time, so the system is
initializing itself.
initializing itself.
Name Full!
There is no more space to store track, disc or group
titles.
titles.
No Change
While attempting to change the recording level after
recording, you pressed ENTER/YES without
actually changing the recording level, so no change
was made.
recording, you pressed ENTER/YES without
actually changing the recording level, so no change
was made.
No Disc
There is no disc in the MD deck.
OVER
You have reached the end of the MD while pressing
M during pause mode.
M during pause mode.
Push STOP!
You pressed an invalid button during playback.
—Rehearsal—
The MD is playing the specified point for
confirmation during the A-B Erase Function and the
Divide Function (pages 30 and 33).
confirmation during the A-B Erase Function and the
Divide Function (pages 30 and 33).
Retry
A reading failure has occurred, and the system is
trying to read the data again.
trying to read the data again.
S.F Edit!
You attempted to perform another operation while
in S.F Edit (changing the recording level after
recording, Fade-in, Fade-out) mode.
in S.F Edit (changing the recording level after
recording, Fade-in, Fade-out) mode.
6
HCD-M373
S.F Edit NOW
You pressed ?/1 while in S.F Edit (changing the
recording level after recording, Fade-in, Fade-out)
mode.
recording level after recording, Fade-in, Fade-out)
mode.
Smart Space
The signal was input again after silence continued
for 3 or more but less than 30 seconds during digital
recording, and the silence was cut to 3 seconds.
for 3 or more but less than 30 seconds during digital
recording, and the silence was cut to 3 seconds.
Step Full!
You tried to program 26 or more tracks (steps).
TOC Reading
The MD deck is reading the TOC information of the
MD.
MD.
TOC Writing
The MD deck is writing the information of recorded
or edited contents.
or edited contents.
Track End
You have reached the end of the track while
adjusting the dividing point during the Divide
Function.
adjusting the dividing point during the Divide
Function.
Tr Protected
Tracks and other data that have been checked out on
Net MD equipment are protected, so you cannot use
some of the MD editing functions.
Net MD equipment are protected, so you cannot use
some of the MD editing functions.
TAPE
Cannot SYNC!
There is no tape in the tape deck, or the tab has been
removed from the cassette.
removed from the cassette.
No Tab
You cannot record the tape because the tab has been
removed from the cassette.
removed from the cassette.
No Tape
There is no tape in the tape deck.
Timer
OFF TIME NG!
The Daily Timer start and end times are set to the
same time.
same time.
OVERLAP!
The Daily Timer setting or the Timer Recording
setting overlaps with part or all of another timer
setting.
setting overlaps with part or all of another timer
setting.
Optional personal computer
Buffer
The personal computer is preparing the amount of
data needed for playback while using the WEB
RADIO function.
data needed for playback while using the WEB
RADIO function.
Busy NOW!
You pressed NET MD during check in or check out.
Wait until the operation is completed.
Wait until the operation is completed.
Cannot Found
• Check that the personal computer is correctly
connected to the internet while using the WEB
RADIO function.
RADIO function.
• Check that the URL registered to the preset is
input correctly.
Cannot Pause
• The MIDI file plays while using the MUSIC
LIBRARY function. You cannot pause MIDI file
playback.
playback.
• You are playing a broadcast station that cannot be
paused while using the WEB RADIO function.
Cannot Play
Check that the music file is registered correctly to
the MUSIC LIBRARY.
the MUSIC LIBRARY.
Check USB
The USB cable is not connected properly. Check the
connection.
connection.
CONNECT
Check in and check out is underway. (If you attempt
an invalid operation at this time, “CONNECT!”
appears.)
an invalid operation at this time, “CONNECT!”
appears.)
Connecting
The personal computer is connecting to the
broadcast station server.
broadcast station server.
Disconnect
• Check that the personal computer is correctly
connected to the internet when using the WEB
RADIO function.
RADIO function.
• You were disconnected from the broadcast station
server.
Net MD
The Net MD function is on. (If you attempt an
invalid operation at this time, “Net MD!” appears.)
invalid operation at this time, “Net MD!” appears.)
7
HCD-M373
How to Operate the Self-diagnostics Function (Error History Display Mode)
Note:
Note:
Use the self-diagnostics function in the "error history display mode" of the test mode. The least required procedure is described
below. Do not enter any other modes by mistake. If you have entered any other modes accidentally, press the MENU/NO “R”
button to exit the mode.
below. Do not enter any other modes by mistake. If you have entered any other modes accidentally, press the MENU/NO “R”
button to exit the mode.
1.
Press the
?/1
button to turn on the power.
2.
Press the FUNCTION button to select the “MD” function.
3.
While pressing the x button and the REC MODE button at the same time, press the
Z
(MD) button.
4.
Press the
>
“R” button to display “[Service]”. Then press the ENTER/YES “R” button.
5.
Press the
>
“R” button to display “Err Display”.
6.
Press the ENTER/YES “R” button to enter the error history display mode and “op rec tm” appears.
7.
Select the desired contents that you want to display or to execute using the
.
“R” button or the
>
“R” button.
8.
Press the TIMER SET “R” button to display or to execute the selected contents.
9.
Press the TIMER SET “R” button again to return to step 7.
10. Press the MENU/NO “R” button. The message “Err Display” appears and you exit the error history mode.
11. Press the REPEAT “R” button to exit the test mode.
12. Press the
11. Press the REPEAT “R” button to exit the test mode.
12. Press the
?/1
button to turn off the power.
Note 1:
About “R”
As this unit has only a few buttons, some operations require the use of remote commander (RM-SM100EW/provided with unit) buttons. These
operations are indicated as “R” in this manual.
As this unit has only a few buttons, some operations require the use of remote commander (RM-SM100EW/provided with unit) buttons. These
operations are indicated as “R” in this manual.
Example:
MENU/NO “R”
...Press the
MENU/NO
button of the remote commander.
Note 2:
Incorrect operations may be performed if the test mode is not entered properly.
In this case, press the ?
In this case, press the ?
/1
button to turn the power off, and retry to enter the test mode.