Sony CMT-M100MD / HCD-M10 Service Manual ▷ View online
7
HCD-M10
DRAWING OUT THE TRAY DURING POWER OUT
tray
gear(B)
First turn the whole of cam block in the arrow
A
direction with fingers,
then put out tray by turning gear (B) in the arrow
B
direction.
• Perform after removing front panel.
B
A
cam block
CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS IN MD
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “Section 5 Electrical Adjustments”.
Details of the procedures are described in “Section 5 Electrical Adjustments”.
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for adjustments.
When performing adjustments, use the specified values for adjustments.
When performing adjustments, use the specified values for adjustments.
• 0.9 mW power
Specified value : 0.80 to 0.96 mW
• 7.0 mW power
Specified value : 6.8 to 7.2 mW
Iop (at 7.0mW)
• Labeled on the optical pick-up
Iop value
±
10mA
• Unsatisfactory if displayed as “NG : XXXX”NG
(XXXX are arbitrary numbers)
• Unsatisfactory if displayed as “T=@@ (##) [NG]”
NG
(@@, ## are both arbitrary numbers)
Laser power check
(6-2 : See page 33)
Auto check
(6-4 : See page 34)
Temperature
Temperature
compensation
offset check
(6-1 : See page 33)
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
(Unsatisfactory if specified value is not satisfied)
• Clean the optical pick-up
• Adjust again
• Replace the optical pick-up
• Replace the optical pick-up
• Replace the optical pick-up
• Check for disconnection of the circuits around
D101 (BD board)
• Check the signals around IC101, IC151, CN102,
CN103 (BD board)
Measure if unsatisfactory
8
HCD-M10
JIG FOR CHECKING BD (MD) BOARD WAVEFORM
The special jig (J-2501-196-A) is useful for checking the waveform of the BD (MD) board. The names of terminals and the checking items
to be performed are shown as follows.
to be performed are shown as follows.
GND : Ground
I+3V : For measuring Iop (Check the deterioration of the optical pick-up laser)
Iop
I+3V : For measuring Iop (Check the deterioration of the optical pick-up laser)
Iop
: For measuring Iop (Check the deterioration of the optical pick-up laser)
TE
: TRK error signal (Traverse adjustment)
VC
: Reference level for checking the signal
RF
: RF signal (Check jitter)
FE
: Focus error signal
I+3V
CN105
Iop
TE
VC
GND
FE
RF
I+3V
Iop
GND
TE
FE
VC
RF
Iop
GND
TE
FE
VC
RF
I+3V
Iop
GND
TE
FE
FE
VC
RF
1
7
for
MDM-7B4M
9
HCD-M10
CLEANING THE OPTICAL PICK-UP (CD PLAYER)
1
Floating screw
3
BU-K4BD43
2
CD mechanism deck
4
Rotate it in the
direction of the arrow
A
.
A
B
5
Move it in the
direction of the arrow
B
.
6
Clean the lens block
by cotton swab
Optical pick-up
Note 1:
In cleaning the lens, do not apply an excessive force
As the optical pick-up is vulnerable, application of
excessive force could damage the lens holder.
excessive force could damage the lens holder.
Note 2:
In cleaning, do not use a cleaner other than exclusive
cleaning liquid. (KK-91 or isopropyl alcohol)
Note 3:
Wipe the obujective lens spirally from center toward
outside. (See Figure A)
(FIGURE A)
10
HCD-M10
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Main unit
3
1
6
7
qj
qh
qg
qf
4
8
9
0
qa
qs
qd
qk
ql
w;
wa
CD disc tray qs (9)
CD NX 3 (9, 11)
Cover qj
Display window 4
ENTER/START qd (22, 24, 46,
CD NX 3 (9, 11)
Cover qj
Display window 4
ENTER/START qd (22, 24, 46,
47)
FM MODE qg (44)
FUNCTION wa (9, 11, 13, 15, 17,
FUNCTION wa (9, 11, 13, 15, 17,
18, 21, 25, 26, 31–39, 41, 46,
48, 53)
48, 53)
GROUP indicator 2 (18, 21, 22,
32–34)
MD insertion slot 5
MD NX 3 (15, 17, 18, 21, 25)
MD NX 3 (15, 17, 18, 21, 25)
PHONES jack qk
PLAY MODE/DIRECTION qh
PLAY MODE/DIRECTION qh
(9, 11, 13, 15, 17, 24, 30,
46–48)
46–48)
REC MODE qd (26)
Remote sensor 6
REPEAT qg (10, 16)
SYNCHRO MODE qd (22, 24,
Remote sensor 6
REPEAT qg (10, 16)
SYNCHRO MODE qd (22, 24,
46, 47)
TAPE nN w; (46–48)
TUNER BAND ql (43, 44)
TUNING MODE qh (43, 44)
TUNING +/– 8 (44)
VOLUME +/– 0
TUNER BAND ql (43, 44)
TUNING MODE qh (43, 44)
TUNING +/– 8 (44)
VOLUME +/– 0
BUTTON DESCRIPTIONS
?/1 (power) 1 (8, 20, 30, 43,
44, 50, 52)
Z PUSH OPEN/CLOSE 7 (46)
m/M 8 (10, 16, 37, 39, 43,
m/M 8 (10, 16, 37, 39, 43,
44, 46)
l/L 8 (10, 11, 13,
16–18, 26, 31, 33–38, 40, 41,
43)
43)
x
8 (10, 16, 21, 23–25, 29,
46–48)
Z MD 9 (15, 16, 20, 30)
Z CD qa (9, 10)
z MD qd (21, 25, 28, 40)
z TAPE qd (48)
X TAPE qf (46, 48)
Z CD qa (9, 10)
z MD qd (21, 25, 28, 40)
z TAPE qd (48)
X TAPE qf (46, 48)
5
2
Click on the first or last page to see other CMT-M100MD / HCD-M10 service manuals if exist.