Sony CMT-LX40I / HCD-LX40I Service Manual ▷ View online
HCD-LX40i
33
Pin No.
Pin Name
I/O
Description
60
MS
I
Micro controller interface mode selection signal input terminal Fixed at “H” in this set
61
DOUT
O
Digital audio data output terminal Not used
62
AOUT1
O
Audio data output terminal Not used
63
BCKO
O
Bit clock signal output terminal Not used
64
LRCKO
O
L/R sampling clock signal output terminal Not used
65
AIN
I
Digital audio data input terminal Not used
66
BCKI
I
Bit clock signal input terminal Not used
67
LRCKI
I
L/R sampling clock signal input terminal Not used
68
VDD1
-
Power supply terminal (+1.5V)
69
VSS1
-
Ground terminal
70
AWRC
-
Not used
71
PVDD3
-
Power supply terminal (+3.3V)
72
PDO
O
Phase error margin signal between EFM signal and PLCK signal output terminal
73
TMAXS
O
TMAX detection signal output terminal Not used
74
TMAX
O
TMAX detection signal output terminal
75
LPFN
I
Inverted signal input from the operation amplifi er for PLL loop fi lter
76
LPFO
O
Signal output from the operation amplifi er for PLL loop fi lter
77
PVREF
I
Reference voltage (+1.65V) input terminal
78
VCOF
O
VCO fi lter output terminal
79
PVSS3
-
Ground terminal
80
SLCO
O
EFM slice level output terminal
81
RFI
I
RF signal input terminal
82
RFRPI
I
RF ripple signal input terminal
83
RFEQO
O
EFM slice level output terminal
84
VRO
O
Reference voltage (+1.65V) output terminal
85
RESIN
O
External resistor connection terminal
86
VMDIR
O
Reference voltage (+1.65V) output terminal for automatic power control circuit
87
TESTR
O
Low-pass fi lter terminal for RFEQO offset correction
88
AGCI
I
RF signal amplitude adjustment amplifi cation input terminal
89
RFO
O
RF signal generation amplifi cation output terminal
90
RVDD3
-
Power supply terminal (+3.3V)
91
LDO
O
Laser diode on/off control signal output to the automatic power control circuit
“H”: laser diode on
“H”: laser diode on
92
MDI
I
Light amount monitor input from the laser diode of optical pick-up block
93
RVSS3
-
Ground terminal
94
C
I
Main beam (C) input from the optical pick-up block
95
A
I
Main beam (A) input from the optical pick-up block
96
D
I
Main beam (D) input from the optical pick-up block
97
B
I
Main beam (B) input from the optical pick-up block
98
F
I
Sub beam (F) input from the optical pick-up block
99
TNPC
O
External capacitor connection terminal
100
E
I
Sub beam (E) input from the optical pick-up block
HCD-LX40i
34
PANEL BOARD IC502 MB90F831PF-G-SPE1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
O-USBRESET/
DAB1.2V
O
Power on/off control signal output terminal for the DAB section
2
O-POWER
O
Main power on/off control signal output terminal “H”: main power on
3
O-AMP-ON
O
Output muting on/off signal output to the power amplifi er
4
O-CD/USM 3.3V ON
O
CD power on/off control signal output terminal “H”: CD power on
5
O-LED
O
LED drive signal output terminal for the LCD back light
6
I-RDS DS
I
RDS data input terminal
7
I-TU-DO
I
Serial data input from the AM/FM DET
8
O-CD-LOAD OUT
O
Motor drive signal output terminal for the loading section
9
I-RMC
I
Remote control signal input from the remote control receiver
10
O-CD-LOAD IN
O
Motor drive signal output terminal for the loading section
11
O-FUNC SC
O
Serial data transfer clock signal output to the electrical volume
12
O-FUNC SD
O
Serial data output to the electrical volume
13
X0A
I
Sub system clock input terminal (32.768 kHz)
14
X1A
O
Sub system clock output terminal (32.768 kHz)
15
VCC
-
Power supply terminal (+3.1V)
16
VSS
-
Ground terminal
17 to 20
BUS0 to BUS3
O
Serial data output to the CD-MP3 processor
21
O-IPOD POWER
O
VBUS power supply on/off control signal output terminal
22
O-LED-STBY
O
LED drive signal output terminal for STANDBY indicator
23
O-CD-DR MUTE
O
Motor drive on/off control signal output to the motor/coil driver
24
I-CD REQ
I
Request signal input from the CD-MP3 processor
25
O-CD BUCK
O
Serial data transfer clock signal output to the CD-MP3 processor
26
O-CD CCE
O
Chip enable signal output to the CD-MP3 processor
27
O-CD RESET
O
System reset signal output to the CD-MP3 processor “L”: reset
28
O-USB SEL/
DAB 3.3VSEL
O
Power on/off control signal output terminal for the DAB section
29
I-UXB TXD/DAB DO
I
Serial data input terminal
30
I-USB DO
I
Clear to send signal input terminal Not used
31
O-USB RXD/DAB DI
O
Serial data output terminal
32
AVCC
-
Power supply terminal (+3.2V)
33
I-IPOD TXD
I
Serial data input from the iPod connector
34
O-USB DI
O
Ready to send signal output terminal Not used
35
AVSS
-
Ground terminal
36
I-P-MONI
I
Power monitor signal input terminal
37, 38
I-KEY_1, I-KEY_2
I
Front panel key input terminal (A/D input)
39
I-KEY_3
I
Destination setting terminal
40
I-SW CD CHECK/
OUT
I
Switch detection signal input terminal for loading section
41
I-KEY WAKE UP
I
Front panel key input terminal (A/D input) for the power key
42
I-HOLD
I
Hold signal input terminal
43
I-CD SBSY
I
Subcode block sync signal input from the CD-MP3 processor
44
VSS
-
Ground terminal
45
I-RDS SC
I
Serial data transfer clock signal input terminal
46
I-TU ANSD
I
Auto gain control signal input terminal
47
O-IPOD-RXD
O
Serial data output to the iPod connector
48
I-IPOD DETECT
I
iPod detection signal input terminal
49
SEL USB-IPOD
O
Function selection signal output terminal Not used
50
SEL USB-WM/I-
MODEL
O
Function selection signal output terminal Not used
51 to 53
MD2 to MD0
-
Not used
54
RSTX
I
Reset signal input from the reset switch “L”: reset
55
O-TU-CE
O
Chip enable signal output to the AM/FM DET
56
O-TU-CLK
O
Serial data transfer clock signal output to the AM/FM DET
57
O-TU-DI
O
Serial data output to the AM/FM DET
58
VLCD
-
Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage
59 to 62
COM0 - COM3
O
Common drive signal output to the liquid crystal display
63, 64
SEG0, SEG1
O
Segment drive signal output to the liquid crystal display
65
VCC
-
Power supply terminal (+3.1V)
HCD-LX40i
35
Pin No.
Pin Name
I/O
Description
66
VSS
-
Ground terminal
67 to 89
SEG2 to SEG24
O
Segment drive signal output to the liquid crystal display
90
VCC
-
Power supply terminal (+3.1V)
91
VSS
-
Ground terminal
92
X1
I
Main system clock output terminal (6 MHz)
93
X0
O
Main system clock input terminal (6 MHz)
94 to 100
SEG25 to SEG31
O
Segment drive signal output to the liquid crystal display
36
HCD-LX40i
SECTION 6
EXPLODED VIEWS
1
4-233-372-02 FOOT
(FELT)
2
4-125-088-21 PANEL
(BACK)
#1
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
#3
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#4
7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
6-1. PANEL (BACK) SECTION
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet’s Color
The components identifi ed by mark
0
or dotted line with mark
0 are critical for
safety.
Replace only with part number specifi ed.
Replace only with part number specifi ed.
#3
#3
#3
#1
#4
#4
1
2
1
panel (front) section
MAIN board section
#1
not supplied
(FFC SUPPORT board)
(FFC SUPPORT board)
Click on the first or last page to see other CMT-LX40I / HCD-LX40I service manuals if exist.