Sony CMT-L1 / HCD-L1 Service Manual ▷ View online
16
HCD-L1
3-15. BD Board
3-16. C MOTOR Board, L.SENSOR Board
6
BD board
3
screw
(BLK)
(RED)
1
Remove solder (two portions ).
2
Remove solder (two portions ).
5
hook
4
flxible board
3
two screws
(+BTP M 2.6
×
6)
q;
screw
(+BTP M 2.6
×
6)
5
C.MOTOR board
6
motor (CK) assy
(M701)
2
Remove solder
(two portions ).
1
belt (CDM71 )
9
Connector
(CN755)
8
Connector
(CN753)
7
Connector
(CN754)
4
Connector
(CN711)
qa
L.SENSOR board (R)
17
HCD-L1
3-17. Base Unit (BU-31BD63A)
3-18. Holder Assy, Sled Motor Assy
5
base unit
(BU-31BD)
2
screw
(+PTPWH M2.6)
cam
shaft
SPT pulley assy
shaft
1
1
4
3
Rotate the SPT pulley assy in the direction of to move the Base unit shaft
forward.
forward.
(BLK)
9
two screws
(+PTPWH M2.6)
8
screw
(+PTPWH M2.6)
qs
screw
(+P 2
×
3)
qd
sled motor assy
q;
hook
qa
base unit
holder assy
6
tension coil spring (holder)
7
tension coil spring (holder)
5
BD board
1
Remove solder
(two portions ).
2
Remove solder
(two portions ).
4
flxible board
3
screw
(+BTP 2
×
8)
(RED)
18
HCD-L1
3-19. RTR Pulley Assy
3-20. SPT Pulley Assy
3
RTR pulley assy
RTR pulley assy
1
claw
2
2
Disengage the claw and rotate the RTR pulley assy in the direction of , and
remove your hands at the position where the shaft agrees with the hole shape on the
chassis.
remove your hands at the position where the shaft agrees with the hole shape on the
chassis.
2
SPT pulley assy
SPT pulley assy
1
1
When installing, align the protruded portion of the KT gear with groove of the SPT
pulley assy.
pulley assy.
Rotate the SPT pulley assy in the direction of , and remove your hands
at the position where the shaft agrees with the hole shape on the chassis.
at the position where the shaft agrees with the hole shape on the chassis.
19
HCD-L1
[Key Check Mode]
* Keyboard check.
Procedure:
1.
Procedure:
1.
Press the ?/1 button to turn the set ON.
2.
To enter the test mode, press three buttons DISPLAY , NX
and > simultaneously.
and > simultaneously.
3.
In the key check mode, the fluorescent indicator displays
“KEY00”. Each time a button is pressed, “KEY00” value
increases. However, once a button is pressed, it is no longer
taken into account.
“KEY00”. Each time a button is pressed, “KEY00” value
increases. However, once a button is pressed, it is no longer
taken into account.
4.
To exit from this mode, press three buttons DISPLAY , NX
and > simultaneously.
and > simultaneously.
[Version Display Mode]
* The version or destination is displayed.
Procedure:
1.
Procedure:
1.
Press the ?/1 button to turn the set ON.
2.
To enter the test mode, press three buttons DISPLAY , VOL+
and VOL– simultaneously.
and VOL– simultaneously.
3.
The model name and destination are displayed.
4.
Press the DISPLAY button. The STR version is displayed.
5.
Press the DISPLAY button again. The CD version is displayed.
6.
Press the DISPLAY button. The model name and destination
are displayed again.
are displayed again.
7.
To exit from this mode, press the ?/1 button to turn off the set.
[FL Tube Test Mode]
* All fluorescent segments are tested.
Procedure:
1.
Procedure:
1.
Press the ?/1 button to turn the set ON.
2.
To enter the test mode, press three buttons DISPLAY , NX
and VOL– simultaneously.
and VOL– simultaneously.
3.
All segments are turned on.
4.
Press the DISPLAY button. All segments are turned off.
5.
Press the DISPLAY button. Confirm the pattern of segments.
6.
Press the DISPLAY button. Confirm the pattern of segments.
7.
Every pressing of the DISPLAY button turns on each segment
one after another in the same order.
one after another in the same order.
8.
To exit from this mode, press the ?/1 button to turn off the set.
[Amp Test Mode]
* Combinatin of preset equalizer and volume is changed for the
amplifier test.
Procedure:
1.
amplifier test.
Procedure:
1.
Press the ?/1 button to turn the set ON.
2.
To enter the test mode, press three buttons . , NX and
> simultaneously.
> simultaneously.
3.
The message “7[TESTMIN]” appears.
4.
Press the DISPLAY and NX buttons simultaneously.
5.
The message “8[TESTMID]” appears.
6.
The messages “9[TESTMAX]”, “10[TESTSUR]”, “7[TESTMIN]”,
, , are changed by every pressing of the DISPLAY and NX
buttons simultaneously.
, , are changed by every pressing of the DISPLAY and NX
buttons simultaneously.
7.
Volume level is changeable at three steps as “VOLUME MIN”,
“VOLUME 21”, “VOLUME MAX” by pressing VOL+ or
VOL– button.
“VOLUME 21”, “VOLUME MAX” by pressing VOL+ or
VOL– button.
8.
In this test mode, the tuning mode is set to the preset mode.
9.
To exit from this mode, press the ?/1 button to turn off the set.
[Forced Reset]
* All micro-processors are forced to reset at the same time.
Procedure:
1.
Procedure:
1.
Press the ?/1 button to turn the set ON.
2.
Press three buttons DISPLAY , TUNER/BAND and
FUNCTION simultaneously.
FUNCTION simultaneously.
3.
The fluorescent indicator tube displays the message “COLD
RESET” and the set is reset. Then the set is turned off.
RESET” and the set is reset. Then the set is turned off.
[CD Ship Position]
Procedure:
1.
1.
Press the ?/1 button to turn the set ON.
2.
Press the FUNCTION button for the setting CD.
3.
Press three buttons . , VOL+ and VOL– simultaneously.
4.
The fluorescent indicator tube displays the message
“STANDBY” and CD is set to the shipment position. Then the
set is turned off.
“STANDBY” and CD is set to the shipment position. Then the
set is turned off.
[Aging Mode]
Procedure:
1.
1.
Press the ?/1 button to turn the set ON.
2.
Insert the disc.
3.
Select the FUNCTION to CD.
4.
To enter the test mode, press three buttons . , TUNER/BAND
and Z OPEN simultaneously.
and Z OPEN simultaneously.
5.
Aging operation starts automatically.
6.
The CD cover opens ,closes and the first track is played. Then
the last track is played.
the last track is played.
7.
The CD cover opens again, and the message “AGIN00000001”
is displayed. This value is cycle times of aging operation and
displays hexadecimal data.
is displayed. This value is cycle times of aging operation and
displays hexadecimal data.
8.
The cover closes and aging operation is continued.
9.
To exit from this mode, press the ?/1 button to turn off the set.
PROGRAM REP
TEXT
TRACK TUNED
MONO
1
DISC
STEREO
AUTO PRESET
DSG
SHUFFLE
DAILY
SLEEP
c
REP
TEXT
TRACK
STEREO
AUTO
DSG
SHUFFLE
DAILY
PROGRAM TUNED
MONO
1
DISC
PRESET
SLEEP
c
SECTION 4
TEST MODE
Click on the first or last page to see other CMT-L1 / HCD-L1 service manuals if exist.