Sony CMT-FX200 / CMT-FX205 / HCD-FX200 / HCD-FX205 Service Manual ▷ View online
HCD-FX200/FX205
5
SECTION 2
DISASSEMBLY
2-3. TOP PANEL BLOCK
(Page
(Page
6)
2-2. PANEL (REAR) BLOCK
(Page
(Page
5)
2-7. BASE UNIT (BU-D1BD73U)
(Page
(Page
8)
2-4. FRONT PANEL BLOCK
(Page
(Page
6)
2-8. OPTICAL PICK-UP BLOCK
(DA11MMVGP)
(Page
(DA11MMVGP)
(Page
8)
2-5. KNOB
(VOL)
(Page
7)
2-6. MAIN
BOARD
(Page
7)
SET
3
2 two screws
(BVTP3
u 10)
4 panel (rear) block
1 three screws
(BVTP3
u 8)
2 four screws
(BVTP3
u 10)
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. PANEL (REAR) BLOCK
Note: This illustration sees the set from rear side.
HCD-FX200/FX205
6
2-3. TOP PANEL BLOCK
Note: This illustration sees the set from rear side.
1 connector
(SW880)
4 connector
(CN914)
8 top panel block
5 claw
2 Extend the coating clip.
5 claw
3 flexible flat cable (19 core) (CN402)
7 three claws
6
2-4. FRONT PANEL BLOCK
0 front panel block
5 lead wire (from USB board)
8 claw
4 screw (BV3)
6 floating screw (PTPWH M2.6)
3 flexible flat cable (21 core) (CN912) (except AEP)
flexible flat cable (23 core) (CN911) (AEP)
1 connector (CN913)
2 Lift up the lead pin.
9
8 claw
7 screw
(BVTP3
u 8)
HCD-FX200/FX205
7
2-6. MAIN BOARD
2-5. KNOB
(VOL)
Note: This illustration sees the front panel block from PANEL board side.
2 knob (VOL)
hole
1 Push the knob (VOL)
by flat-head screwdriver.
front panel block
PANEL board
3 connector
(CN904)
1 connector (CN901)
7 MAIN board
4 two screws (BV3)
6 screw
(BVTP3
u 8)
2 connector
(CN902)
5
HCD-FX200/FX205
8
2-7. BASE UNIT (BU-D1BD73U)
Note 1: This illustration sees the top panel block from base unit side.
1 four floating screws
(PTPWH M2.6)
3 two vibration proof rubbers
(red)
4 two vibration proof rubbers
(green)
6 cover (D1)
7 base unit
(BU-D1BD73U)
2
5 four claws
Note
2: Four claws might be fixed by bond.
Please fix four claws by the bond when
you replace the cover (D1).
2-8. OPTICAL PICK-UP BLOCK (DA11MMVGP)
1 Remove four solders.
2 Solder the short-land.
4 BD73U board block
Note 2: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the wire (flat type) (16 core).
7 optical pick-up block
(DA11MMVGP)
5 tapping screw (P2)
6 shaft (support)
3 wire (flat type) (16 core) (optical pick-up)
Note 1: When disconnecting the wire (fl at type) (16 core) of optical pick-up block, solder the short-land.
Click on the first or last page to see other CMT-FX200 / CMT-FX205 / HCD-FX200 / HCD-FX205 service manuals if exist.