Sony CMT-EX5 / HCD-EX5 Service Manual ▷ View online
7
HCD-EX5
Replacing the battery in
the remote
the remote
1
Slide out and remove the battery case.
2
Insert a new lithium battery CR2025
with the + side facing up.
with the + side facing up.
Setting the clock
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
The day indication flashes.
3
Press
.
or
>
on the remote
repeatedly to set the day, then press
ENTER/YES on the remote.
ENTER/YES on the remote.
The hour indication flashes.
4
Press
.
or
>
on the remote
repeatedly to set the hour, then press
ENTER/YES on the remote.
ENTER/YES on the remote.
The minute indication flashes.
5
Press
.
or
>
on the remote
repeatedly to set the minuite, then
press ENTER/YES on the remote.
press ENTER/YES on the remote.
If you made a mistake
Press TCURSOR or CURSORt on the remote
repeatedly until the indication you want to change
(day, hour, minuite) flashes, and then change the
setting.
repeatedly until the indication you want to change
(day, hour, minuite) flashes, and then change the
setting.
To adjust the clock
1
Press CLOCK/TIMER SET on the remote.
2
Press
.
or
>
on the remote
repeatedly to select “CLOCK SET?”, then
press ENTER/YES on the remote.
press ENTER/YES on the remote.
3
Do the same procedures as steps 3 to 5
above.
above.
A lithium battery CR2025
3
Slide the battery case back in.
Tip
When the remote no longer operates the system,
replace the battery with a new one.
replace the battery with a new one.
Note
If you do not use the remote for a long period of time,
remove the battery to avoid possible damage from
battery leakage and corrosion.
remove the battery to avoid possible damage from
battery leakage and corrosion.
Notes on lithium battery
• Keep the lithium battery out of the reach of
children. Should the battery be swallowed,
immediately consult a doctor.
immediately consult a doctor.
• Wipe the battery with a dry cloth to assure a good
contact.
• Be sure to observe the correct polarity when
installing the battery.
• Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
WARNING
Battery may explode if you mistreated.
Do not recharge, disassemble or dispose of in fire.
Do not recharge, disassemble or dispose of in fire.
8
HCD-EX5
SECTION 3
DISASSEMBLY
•
The equipment can be removed using the following procedure.
HOLDER ASSY,
SLED MOTOR ASSY (M102)
C MOTOR BOARD,
L.SENSOR BOARD
L.SENSOR BOARD
BASE UNIT (BU-31BD63A)
CASE BUTTON ASSY,LID BOARD
RTR PULLEY ASSY,RTL PULLEY ASSY,
BELT (CDM71), BELT (ROLLER) (L)
SPT PULLEY ASSY,GEAR (RT)ASSY,
GEAR (KT), BELT (CDM71)
SET (HCD-EX5)
CASE
OC BOARD,OS BOARD
BD BOARD
POWER BOARD
MAIN BOARD,TUNNER
CD MECHANISM
(CDM71C-31BD63A)
LID(CD)
ORNAMENT
(MECHA PANEL)
L.MOTOR BOARD
ENCODER BOARD,
D.SENSOR BOARD
D.SENSOR BOARD
GLASS WINDOW ASSY (U)
9
HCD-EX5
Note :
Follow the disassembly procedure in the numerical order given.
3-1. Case
3-2. OC Boad,OS Boad
2
six
screws (+BVTP 3
×
8)
1
cover (back)
3
cover (bottom)
6
connector
(CN621)
7
case
4
four screws (+BVTP 3
×
8)
5
4
guide disc assy
6
OS board
8
OC board
5
two claws
7
two claws
3
bracket
case
1
two screws (+BTP 2.6
×
8)
2
screw (+BTP 2.6
×
8)
10
HCD-EX5
3-3. Glass Window Assy (U)
3-4. POWER Board
5
four
step screws (slider)
7
glass window assy (U)
1
three screws (+BVTP 3
×
8)
3
three screws (+BVTP 3
×
8)
2
retainer plate (R)
4
retainer plate (L)
6
four bushings (bracket)
qh
POWER board
qd
five screws (+BVTP 3
×
8)
qf
shield (lower)
qg
insulator (power 1)
2
three screws
(+BVTP 3
×
8)
3
clamp
7
two screws (+BVTP 3
×
8)
8
two screws
(+BVTP 3
×
8)
9
two screws
(+BVTP 3
×
8)
4
three screws
(+BVTP 3
×
8)
qs
shield (upper)
q;
four screws
(+BVTP 3
×
8)
qa
four screws
(+BVTP 3
×
8)
1
two screws
(+BVTP 3
×
8)
6
connector
5
flat type wire
(15 core)
Click on the first or last page to see other CMT-EX5 / HCD-EX5 service manuals if exist.