Sony CMT-EX200 / HCD-EX200 Service Manual ▷ View online
5
HCD-EX200
Shipment Mode
• Mode for setting the state of the unit to the state at shipment. When returning the unit to the customer after completing servicing, set to the
• Mode for setting the state of the unit to the state at shipment. When returning the unit to the customer after completing servicing, set to the
shipment mode.
Procedure :
Connect the power plug to the outlet while pressing the
Connect the power plug to the outlet while pressing the
1/u button.
Change-over of AM tuner Step between 9kHz and 10kHz.
• A step of AM channels can be changed over between 9kHz and 10kHz.
• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1. Press the
1. Press the
1/u button to turn on the set ON.
2. Select the function “TUNER”, and press the TUNER/BAND button to select the BAND “AM”.
3. Press the
3. Press the
1/u button to turn on the set OFF.
4. Press the
1/u button while pressing the )+/TUNING + button, and the display of liquid crystal indicator tube changes to “AM 9k
STEP” or “AM 10k STEP”, and thus the channel step is changed over.
Switching the TAPE IN input level attenuate function ON/OFF
• The attenuate function of the line input level (TAPE IN) of this unit can be turned ON/OFF.
• The attenuate function of the line input level (TAPE IN) of this unit can be turned ON/OFF.
Procedure:
1. Press the
1. Press the
1/u button to turn ON the power.
2. Press the FUNCTION button and set the function to “TAPE”.
3. Press the
3. Press the
1/u button to turn OFF the power.
4. While pressing the
p button, press the 1/u button to turn ON the power.
5. After “POWER ON” is displayed, “ATT ON” and “ATT OFF” are displayed, and the attenuate function can be switched ON/OFF.
LCD All Lit and Key Check Mode
Procedure:
1. While pressing the FUNCTION button and
1. While pressing the FUNCTION button and
^ button, connect the power plug to the outlet.
2. When the test mode is set, the characters “STEP” are displayed on the LCD.
3. While pressing the DISPLAY button (See page 6), press the
3. While pressing the DISPLAY button (See page 6), press the
^ button. The whole LCD lights up.
4. Each time the FUNCTION button is pressed, the display switches between all lit
n partial lighting 1 n partial lighting 2 n all lit.
5. When the
p button is pressed, “KEY 0” is displayed and the key check mode is set.
6. Each time the button is pressed, the counter counts up. Buttons once pressed will not be counted when pressed again.
When all buttons have been pressed, “KEY OK” is displayed.
7. To end, press the
1/u button to turn OFF the power, and disconnect the power plug from the outlet.
Note:
Pressing buttons other than those specified in steps 4 and 5 displays modes not used in servicing. In such cases, press the
Pressing buttons other than those specified in steps 4 and 5 displays modes not used in servicing. In such cases, press the
1/u button to exit
the mode, and repeat from step 3 again.
All lit
Partial lighting 1
Partial lighting 2
6
HCD-EX200
Displaying the CD Text
• This unit is equipped with a simple CD text display function.
• This unit is equipped with a simple CD text display function.
The text is displayed only for the first 20 songs. As it will not be displayed from the 21st song, do not suspect a fault.
In some cases, special characters may not be displayed or may be substituted by other characters. This is not a fault.
In some cases, special characters may not be displayed or may be substituted by other characters. This is not a fault.
Aging Mode
• The aging mode automatically repeats the operations of the CD.
• The aging mode automatically repeats the operations of the CD.
When an error occurs:
Aging stops
When no error occurs:
Aging is performed repeatedly.
Aging stops
When no error occurs:
Aging is performed repeatedly.
Procedure:
1. Set any CD. (One with a short playback time of the final track is recommended.)
2. While pressing the FUNCTION button and the
1. Set any CD. (One with a short playback time of the final track is recommended.)
2. While pressing the FUNCTION button and the
^ button, connect the power plug to the outlet.
3. When the test mode is set, the characters “STEP” is displayed on the LCD.
4. When the
4. When the
^ button is pressed while pressing the DISPLAY button, “AGING” will be displayed, and aging is performed in the
following sequence. While aging is performed, “REP” will be displayed blinking.
5. Pressing the DISPLAY button during aging displays the cycle number (@ CY where @ is the number of agings).
6. To end aging, press the
6. To end aging, press the
1/u button, turn OFF the power, and disconnect the power plug from the outlet.
Sequence during aging
Reads the TOC
Pauses
Accesses first track
Accesses last track
Plays last track
Eject disc (“OPEN” displayed)
Load disc (“CLOSE” displayed)
Displays number of cycles
Power OFF
Power ON
DISPLAY button
DISPLAY button
Note : Press DISPLAY button
with a thing a fine point
from the bottom of front panel.
with a thing a fine point
from the bottom of front panel.
7
HCD-EX200
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Parts Identification
The items are arranged in alphabetical order.
Main unit
Display window
BUTTON DESCRIPTION
0
FUNCTION 7 (11, 17)
OPEN/CLOSE Z 1 (11)
Remote sensor 9
TUNER/BAND 6 (13)
TUNING +/– 3 (13)
VOL +/– 2
OPEN/CLOSE Z 1 (11)
Remote sensor 9
TUNER/BAND 6 (13)
TUNING +/– 3 (13)
VOL +/– 2
m/M
3
./>
3
x
4
NX
5
?/1
8
8
HCD-EX200
Setting the time
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
Proceed to step 4 when you set the clock for
the first time.
the first time.
3
Press . or >
.
>
.
>
.
>
repeatedly to select
“CLOCK SET”, then press ENTER on
the remote.
the remote.
The day indication flashes.
4
Press
or
repeatedly to set the
day, then press ENTER on the remote.
The hour indication flashes.
5
Press
or
repeatedly to set the
hour, then press ENTER on the remote.
The minute indication flashes.
6
Press
or
repeatedly to set the
minute, then press ENTER on the
remote.
remote.
The clock starts working.
Tip
If you made a mistake or want to change the time,
start over from step 1.
start over from step 1.
Turning off the clock display
in standby mode
in standby mode
Press DISPLAY on the remote while the
system is off.
system is off.
To turn on the clock display, press DISPLAY
on the remote again.
on the remote again.
Notes
• When the Daily Timer is set, you cannot turn off the
clock display.
• The clock display will appear when you set the
Daily Timer during turning off the display.
Remote Control
qg
qh
ql
qk
qj
w;
1 2 3 4
wa
ws
6
7
8
9
5
qf
0
qd
qa
qs
BASS +/– qg (15)
CD N qk (11)
CLOCK/TIMER SELECT 6
CD N qk (11)
CLOCK/TIMER SELECT 6
(17)
CLOCK/TIMER SET 7 (10, 16)
DISPLAY 5 (10, 13)
DSG qd (15)
ENTER 8 (10, 12, 13, 16)
FM MODE 3 (14)
FUNCTION ws (11, 17)
MEMORY 9 (13)
DISPLAY 5 (10, 13)
DSG qd (15)
ENTER 8 (10, 12, 13, 16)
FM MODE 3 (14)
FUNCTION ws (11, 17)
MEMORY 9 (13)
Number buttons w; (12)
OPEN/CLOSE Z 1 (11)
PC/TAPE q; (17)
PLAY MODE wa (11, 12)
REPEAT 3 (12)
SLEEP 2 (16)
SURROUND qh (15)
TREBLE +/– qf (15)
TUNER BAND qj (13)
TUNING MODE wa (13)
VOL +/– qs
OPEN/CLOSE Z 1 (11)
PC/TAPE q; (17)
PLAY MODE wa (11, 12)
REPEAT 3 (12)
SLEEP 2 (16)
SURROUND qh (15)
TREBLE +/– qf (15)
TUNER BAND qj (13)
TUNING MODE wa (13)
VOL +/– qs
BUTTON DESCRIPTIONS
@/1
4
+
/ – qa
.
qa
>
qa
X
qk
x
qk
m
ql
M
ql
Click on the first or last page to see other CMT-EX200 / HCD-EX200 service manuals if exist.