Sony CMT-EX100 / HCD-EX100 Service Manual ▷ View online
9
HCD-EX100
SECTION 3
DISASSEMBLY
3-1. REAR COVER, BOTTOM PLATE, CASE AND EJECT BOARD
Note: Disassemble the unit in the order as shown below.
1
2
Two claws
Rear cover
9
Case with cover (top) assy
3
Four screws
(+BVT3X5)
4
Bottom plate
5
Three screws
(+BVTT3X5)
5
Three screws
(+BVTT3X5)
8
Connector
(from CN602
on Panel board)
on Panel board)
6
B
B
A
A
6
7
Screw (2X3)
Washer
qa
qs
0
Eject board
Set
Panel board and Stabilizer
Amp block
CD block
Motor assy, Cam and SW board
Base unit and Pick up assy
Main board,REG board, Power board
Rear cover, Bottom plate, Case and Eject board
Note: Follow the disassembly procedure in the numerical order given.
10
HCD-EX100
3-3. AMP BLOCK
3-2. PANEL BOARD AND STABILIZER
4
2
3
Remove the Earth clip
Front panel assy
1
Two screws (+BVTT3X5)
5
Two screws
(+BVTT2.6X8)
(+BVTT2.6X8)
5
Three screws
(+BVTT2.6X8)
(+BVTT2.6X8)
7
Panel board
6
Flat type wire
(CN601)
(CN601)
Claw
Stabilizer
Stabilizer
Stabilizer claw
Turn the stabilizer claw in the direction
of the arrow to remove it from the notch
on the stabiholder.
of the arrow to remove it from the notch
on the stabiholder.
Connector
AMP board: CN801
AMP board: CN801
AMP block
Two screw (BVTT3x5)
Screw (BVTT3x5)
Connector
AMP board: CN810
AMP board: CN810
Connector
AMP board: CN802
AMP board: CN802
2
3
4
1
1
5
11
HCD-EX100
3-4. CD BLOCK
3-5. MOTOR ASSY (LOADING BOARD), CAM AND SW BOARD
Note:
The phase adjustment is required in assembly.
Refer to"Section 1. Servicing Note" for details.
Refer to"Section 1. Servicing Note" for details.
Connector
MAIN board: CN351
MAIN board: CN351
Flat type wire (CN301)
Connector
MAIN board: CN302
MAIN board: CN302
1
2
4
5
6
7
8
Screw (BVTT3x5)
3
Two screws (BVTT3x5)
Screw (BVTT3x5)
Two screws (BVTT3x5)
CD block
1
2
3
4
5
6
7
8
9
0
!¡
!™
!£
!¢
!∞
!§
Slider (3)
Slider (2)
Disc holder
Lever (1)
Mecha cover
Motor assy
Loading board
SW board
Two screws (BVTP2.6x8)
Two screws (BVTP2.6x8)
Two screws (BVTP2.6x8)
Two screws (BVTP2.6x8)
Screws (BTP2.6x8)
Screws (PTPWH2.6)
Two screws (M2.6)
Two screws (M2.6)
Cam
12
HCD-EX100
3-6. BASE UNIT AND PICK UP ASSY
1
2
3
4
5
6
7
8
9
0
!™
!£
!¢
!∞
!¡
Two screws (BVTP2.6x8)
Two screws
(BVTP2.6x8)
(BVTP2.6x8)
Guide (L)
Guide (R)
Slider (4)
Slider (4)
Slider (1)
Two screws (PTPWH2.6)
Screws (PTPWH2.6)
Two screws (PTPWH2.6)
Two screws
(PTPWH2.6)
(PTPWH2.6)
Coil spring
Coil spring
BU holder
Pick up assy
3-7. MAIN BOARD (LED BOARD), REG BOARD AND POWER BOARD
Two screws
(BVTT3x5)
(BVTT3x5)
Two screws
(BVTP3x8)
(BVTP3x8)
Two screws (BVTP3x8)
Three screws
(BVTT3x5)
(BVTT3x5)
Two screws
(BVTT3x5)
(BVTT3x5)
Screw (PTPWH2.6)
Screw (BVTT3x5)
Screw (BVTT3x5)
Screw (BVTT3x5)
Main board
Power board
Power cord
REG board
Connector
POWER board: CN903
POWER board: CN903
Back panel
LED board
1
2
3
4
Two screws
(BVTT3x5)
(BVTT3x5)
Screw (BVTT3x5)
Shield case
Flat type wire
(CN702)
(CN702)
Flat type wire (CN701)
5
6
7
8
9
0
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
Warning
After repairs are completed and it has been assembled, be sure to carry out the following checks.
1. Make sure the disc opens and closes smoothly.
2. Make sure the disc does not rub on anything when it is played.
1. Make sure the disc opens and closes smoothly.
2. Make sure the disc does not rub on anything when it is played.
Click on the first or last page to see other CMT-EX100 / HCD-EX100 service manuals if exist.