Sony CMT-EX100 / HCD-EX100 Service Manual ▷ View online
6
HCD-EX100
Displaying the CD Text
• This unit is equipped with a simple CD text display function.
• This unit is equipped with a simple CD text display function.
The text is displayed only for the first 20 songs. As it will not be displayed from the 21st song, do not suspect a fault.
In some cases, special characters may not be displayed or may be substituted by other characters. This is not a fault.
In some cases, special characters may not be displayed or may be substituted by other characters. This is not a fault.
Aging Mode
• The aging mode automatically repeats the operations of the CD.
• The aging mode automatically repeats the operations of the CD.
When an error occurs:
Aging stops
When no error occurs:
Aging is performed repeatedly.
Aging stops
When no error occurs:
Aging is performed repeatedly.
Procedure:
1. Set any CD. (One with a short playback time of the final track is recommended.)
2. While pressing the FUNCTION button and
1. Set any CD. (One with a short playback time of the final track is recommended.)
2. While pressing the FUNCTION button and
^ button, connect the power plug to the outlet.
3. When the test mode is set, the characters “STEP” is displayed on the LCD.
4. When the
4. When the
^ button is pressed while pressing the DISPLAY button, “AGING” will be displayed, and aging is performed in the
following sequence. While aging is performed, “REP” will be displayed blinking.
5. Pressing the DISPLAY button during aging displays the cycle number (@ CY where @ is the number of agings).
6. To end aging, press the
6. To end aging, press the
1/u button, turn OFF the power, and disconnect the power plug from the outlet.
Sequence during aging
Reads the TOC
Pauses
Accesses first track
Accesses last track
Plays last track
Eject disc (“OPEN” displayed)
Load disc (“CLOSE” displayed)
Displays number of cycles
Power OFF
Power ON
DISPLAY button
DISPLAY button
Note : Press DISPLAY button
with a thing a fine point
from the bottom of front panel.
with a thing a fine point
from the bottom of front panel.
7
HCD-EX100
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
8
HCD-EX100
Remote Control
qg
qh
ql
qk
qj
w;
1 2 3 4
wa
ws
6
7
8
9
9
5
qf
0
qd
qa
qs
BASS +/– qg (14)
CD N qk (9)
CLOCK/TIMER SELECT 6
CD N qk (9)
CLOCK/TIMER SELECT 6
(16)
CLOCK/TIMER SET 7 (8, 15)
DISPLAY 5 (8, 12, 14)
DSG qd (14)
ENTER 8 (8, 11, 12, 15)
FM MODE 3 (13)
FUNCTION ws (9, 16)
DISPLAY 5 (8, 12, 14)
DSG qd (14)
ENTER 8 (8, 11, 12, 15)
FM MODE 3 (13)
FUNCTION ws (9, 16)
MEMORY 9 (12)
Number buttons w; (10)
OPEN/CLOSE Z 1 (9)
PC/TAPE q; (16)
PLAY MODE wa (9, 11)
REPEAT 3 (10)
SLEEP 2 (15)
SURROUND qh (14)
TREBLE +/– qf (14)
TUNER BAND qj (12)
TUNING MODE wa (12)
VOL +/– qs
Number buttons w; (10)
OPEN/CLOSE Z 1 (9)
PC/TAPE q; (16)
PLAY MODE wa (9, 11)
REPEAT 3 (10)
SLEEP 2 (15)
SURROUND qh (14)
TREBLE +/– qf (14)
TUNER BAND qj (12)
TUNING MODE wa (12)
VOL +/– qs
BUTTON DESCRIPTIONS
@/1 4
+
+
/ – qa
. qa
> qa
X qk
x qk
m ql
M ql
> qa
X qk
x qk
m ql
M ql
Setting the time
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
Proceed to step 4 when you set the clock for
the first time.
the first time.
3
Press . or >
.
>
.
>
.
>
repeatedly to select
“CLOCK SET”, then press ENTER on
the remote.
the remote.
The day indication flashes.
4
Press
or
repeatedly to set the
day, then press ENTER on the remote.
The hour indication flashes.
5
Press
or
repeatedly to set the
hour, then press ENTER on the remote.
The minute indication flashes.
6
Press
or
repeatedly to set the
minute, then press ENTER on the
remote.
remote.
The clock starts working.
Tip
If you made a mistake or want to change the time,
start over from step 1.
start over from step 1.
Turning off the clock display
in standby mode
in standby mode
Press DISPLAY on the remote while the
system is off.
system is off.
To turn on the clock display, press DISPLAY
on the remote again.
on the remote again.
Notes
• When the Daily Timer is set, you cannot turn off the
clock display.
• The clock display will appear when you set the
Daily Timer during turning off the display.
9
HCD-EX100
SECTION 3
DISASSEMBLY
3-1. REAR COVER, BOTTOM PLATE, CASE AND EJECT BOARD
Note: Disassemble the unit in the order as shown below.
1
2
Two claws
Rear cover
9
Case with cover (top) assy
3
Four screws
(+BVT3X5)
4
Bottom plate
5
Three screws
(+BVTT3X5)
5
Three screws
(+BVTT3X5)
8
Connector
(from CN602
on Panel board)
on Panel board)
6
B
B
A
A
6
7
Screw (2X3)
Washer
qa
qs
0
Eject board
Set
Panel board and Stabilizer
Amp block
CD block
Motor assy, Cam and SW board
Base unit and Pick up assy
Main board,REG board, Power board
Rear cover, Bottom plate, Case and Eject board
Note: Follow the disassembly procedure in the numerical order given.
Click on the first or last page to see other CMT-EX100 / HCD-EX100 service manuals if exist.