Sony CMT-EP505 / HCD-EP505 Service Manual ▷ View online
4
HCD-EP505
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
1. Press the
I/1
button to the power ON with no disc inserted
and press the
[CD]
button.
2. Open the lid for CD.
3. Turn on SW300 as following figure.
4. Confirm the laser diode emission while observing the object-
3. Turn on SW300 as following figure.
4. Confirm the laser diode emission while observing the object-
ing lens. When there is no emission, Auto Power Control cir-
cuit or Optical Pick-up is broken.
Objective lens moves up and down five times for the focus
search.
cuit or Optical Pick-up is broken.
Objective lens moves up and down five times for the focus
search.
SECTION 1
SERVICING NOTES
SW300
Ver 1.1
• MODEL IDENTIFICATION
– Bottom View –
– Bottom View –
Power Voltage Indication
Power Voltage
Indication
AC: 120 V 60 Hz 35 W
AC: 220 – 230 V - 50/60 Hz 40 W
AC: 230 V - 50/60 Hz 40 W
Model
US and Canadian
models
models
Argentina model
Other models
5
HCD-EP505
Main unit
P– Z
PHONES jack qk
PLAY MODE qj
PRESET +/– qd
RDS (European model only)/DIR qj
PLAY MODE qj
PRESET +/– qd
RDS (European model only)/DIR qj
Remote sensor 0
TAPE 3
TIMER indicator 1
TUNER 6
TUNER MEM qh
TUNING +/– qa
VOLUME control qs
TAPE 3
TIMER indicator 1
TUNER 6
TUNER MEM qh
TUNING +/– qa
VOLUME control qs
ALPHABETICAL ORDER
A – M
Cassette compartment qg
CD 4
DIR qj
DISPLAY 2
Display Window 5
CD 4
DIR qj
DISPLAY 2
Display Window 5
ENTER qh
MEGA BASS 8
MUSIC MENU 9
MEGA BASS 8
MUSIC MENU 9
BUTTON DESCRIPTIONS
@/1 (power) wd
CD
. m (go back) qa
M > (go forward) qa
M > (go forward) qa
nN(play) w;
X (pause) ws
Z PUSH OPEN/CLOSE 7
x (stop) ql
X (pause) ws
Z PUSH OPEN/CLOSE 7
x (stop) ql
TAPE
M > (fast forward) qa
X (pause) ws
nN (play) w;
z (recording) wa
. m (rewind) qa
Z PUSH OPEN/CLOSE qf
x (stop) ql
X (pause) ws
nN (play) w;
z (recording) wa
. m (rewind) qa
Z PUSH OPEN/CLOSE qf
x (stop) ql
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
LOCATION OF CONTROLS
– Front Panel –
– Front Panel –
Ver 1.1
6
HCD-EP505
ALPHABETICAL ORDER
A – M
CD wf
CLOCK/TIMER +/– w;
CLOCK/TIMER ON/OFF 2
CLOCK/TIMER +/– w;
CLOCK/TIMER ON/OFF 2
CLOCK/TIMER SET 3
DISPLAY qa
ENTER qf
MEGA BASS qd
MUSIC MENU +/– qh
MUTING qg
ENTER qf
MEGA BASS qd
MUSIC MENU +/– qh
MUTING qg
P – Z
PLAY MODE/RDS
(European model only)/DIR 7
(European model only)/DIR 7
PRESET +/– 9
REPEAT 8
SLEEP 1
TAPE wd
TUNER/BAND 5
REPEAT 8
SLEEP 1
TAPE wd
TUNER/BAND 5
TUNER MEMORY qj
TUNING + q;
TUNING – qk
VOL (volume) +/– qs
TUNING + q;
TUNING – qk
VOL (volume) +/– qs
Remote control
BUTTON DESCRIPTIONS
m (rewind) M
(fast forward) ql
. (go back) >
(go forward) w;
X (pause) ws
nN (play) wa
nN (play) wa
`/1 (power) 4
x (stop) 6
x (stop) 6
tape function.
Ver 1.1
Setting the clock
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
3
Press
.
or
>
on the remote
repeatedly to set the hour.
4
Press ENTER.
5
Press
.
or
>
on the remote
repeatedly to set the minute.
6
Press ENTER.
The clock starts working.
To adjust the clock
1
Press CLOCK/TIMER SET on the remote.
2
Press . or > on the remote to select
“SET CLK”, then press ENTER.
“SET CLK”, then press ENTER.
3
Do the same procedures as step 3 to 6 above.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
the power cord or if a power failure occurs.
HCD-EP505
7
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-4. CD CABINET SECTION
(Page 9)
3-2. FRONT PANEL SECTION
(Page 8)
3-6. TAPE MECHANISM DECK
(CRL3439)
(Page 10)
(Page 10)
3-5. CD MECHANISM DECK
(CS-21SC-1280)
(Page 9)
(Page 9)
3-7. CASSETTE LID
(Page 10)
3-3. MAIN BOARD
(Page 8)
SET