Sony CMT-EP404 / HCD-EP404 Service Manual ▷ View online
3
HCD-EP404
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SW600
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
1.
Press the ?/1 button to the power ON with no disc inserted
and press the CD button.
and press the CD button.
2.
Open the lid for CD.
3.
Turn on SW600 as following figure.
4.
Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down five times for the focus
search.
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down five times for the focus
search.
4
HCD-EP404
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Main unit
P – Z
PHONES jack qk
PLAY MODE qj (8, 9)
PRESET +/– qd (11, 13)
Remote sensor 0
TAPE 3 (14)
TIMER indicator 1 (16, 18)
TUNER 6 (10, 11, 12, 15)
TUNER MEM qh (10, 11)
TUNING +/– qa (10, 11, 12, 13)
VOLUME control qs
PLAY MODE qj (8, 9)
PRESET +/– qd (11, 13)
Remote sensor 0
TAPE 3 (14)
TIMER indicator 1 (16, 18)
TUNER 6 (10, 11, 12, 15)
TUNER MEM qh (10, 11)
TUNING +/– qa (10, 11, 12, 13)
VOLUME control qs
ALPHABETICAL ORDER
A – M
Cassette compartment qg (14)
CD 4 (8, 9, 15)
DISPLAY 2 (12, 19)
Display Window 5 (8, 9, 10,
CD 4 (8, 9, 15)
DISPLAY 2 (12, 19)
Display Window 5 (8, 9, 10,
11)
ENTER qh (7, 9, 10, 11, 13)
MEGA BASS 8 (17)
MUSIC MENU 9 (17)
MEGA BASS 8 (17)
MUSIC MENU 9 (17)
BUTTON DESCRIPTIONS
@/1 (power) wd (7, 16, 18)
CD
. m (go back) qa (8, 9, 14)
M > (go forward) qa (8, 9,
M > (go forward) qa (8, 9,
14)
N (play) w; (8, 9)
X (pause) ws (8)
Z PUSH OPEN/CLOSE 7 (8)
x (stop) ql (8, 9)
X (pause) ws (8)
Z PUSH OPEN/CLOSE 7 (8)
x (stop) ql (8, 9)
TAPE
M > (fast forward) qa (14)
X (pause) ws (14)
N (play) w; (14)
z (recording) wa (15, 16)
. m (rewind) qa (14)
Z PUSH OPEN/CLOSE qf (14)
x (stop) ql (14, 15)
X (pause) ws (14)
N (play) w; (14)
z (recording) wa (15, 16)
. m (rewind) qa (14)
Z PUSH OPEN/CLOSE qf (14)
x (stop) ql (14, 15)
5
HCD-EP404
ALPHABETICAL ORDER
A – M
CD wf (8, 9, 15)
CLOCK/TIMER +/– w; (16, 18)
CLOCK/TIMER ON/OFF 2
CLOCK/TIMER +/– w; (16, 18)
CLOCK/TIMER ON/OFF 2
(16, 18)
CLOCK/TIMER SET 3 (7, 16,
18)
DISPLAY qa (12, 19)
ENTER qf (7, 9, 10, 11, 13, 18)
MEGA BASS qd (17)
MUSIC MENU +/– qh (17)
MUTING qg (17)
ENTER qf (7, 9, 10, 11, 13, 18)
MEGA BASS qd (17)
MUSIC MENU +/– qh (17)
MUTING qg (17)
P – Z
PLAY MODE 7 (8, 9, 13, 14, 15)
PRESET +/– 9 (11, 13)
REPEAT 8 (8)
SLEEP 1 (17)
TAPE wd (14)
TUNER/BAND 5 (10, 11, 12,
PRESET +/– 9 (11, 13)
REPEAT 8 (8)
SLEEP 1 (17)
TAPE wd (14)
TUNER/BAND 5 (10, 11, 12,
15)
TUNER MEMORY qj (10, 11)
TUNING + q; (10, 11, 12, 13)
TUNING – qk (10, 11, 12, 13)
VOL (volume) +/– qs
TUNING + q; (10, 11, 12, 13)
TUNING – qk (10, 11, 12, 13)
VOL (volume) +/– qs
Remote control
BUTTON DESCRIPTIONS
m (rewind) M (fast forward)
ql (8, 14)
. (go back) > (go forward)
w; (7, 8, 14, 15)
X (pause) ws (8, 14)
N (play) wa (8, 9, 14, 15, 16)
`/1 (power) 4 (7, 16, 18)
x (stop) 6 (8, 9, 14, 15)
N (play) wa (8, 9, 14, 15, 16)
`/1 (power) 4 (7, 16, 18)
x (stop) 6 (8, 9, 14, 15)
Setting the clock
1
Turn on the system.
2
Press CLOCK/TIMER SET on the
remote.
remote.
3
Press
.
or
>
on the remote
repeatedly to set the hour.
4
Press ENTER.
5
Press
.
or
>
on the remote
repeatedly to set the minute.
6
Press ENTER.
The clock starts working.
To adjust the clock
1
Press CLOCK/TIMER SET on the remote.
2
Press . or > on the remote to select
“SET CLK”, then press ENTER.
“SET CLK”, then press ENTER.
3
Do the same procedures as step 3 to 6 above.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
the power cord or if a power failure occurs.
6
HCD-EP404
SECTION 3
DISASSEMBLY
• The equipment can be removed using the following procedure.
3-1. Front Panel Section
Note : Follow the disassembly procedure in the numerical order given.
3-6. CD CABINET SECTION
(Page 9)
3-5. DISPLAY BOARD,
HEADPHONE BOARD
HEADPHONE BOARD
(Page 8)
3-1. FRONT PANEL SECTION
(Page 6)
3-3. TAPE MECHANISM DECK
(CFL4318)
(Page 7)
(Page 7)
3-7. CD MECHANISM DECK
(CS-21SC-1280)
(Page 9)
(Page 9)
3-8. CASSETE LID
(Page 10)
3-2. MAIN BOARD
(Page 7)
3-4. POWER BOARD,
POWER TRANSFORMER
POWER TRANSFORMER
(Page 8)
SET
qa
connector
(CN201)
(CN201)
6
two screws
(+K3
(+K3
×
5)
3
two screws
(+BTP2.6
(+BTP2.6
×
10)
1
screw
(+BVTP3
(+BVTP3
×
10)
4
two screws
(+BVTP3
(+BVTP3
×
10)
5
two screws
(+K3
(+K3
×
5)
7
two screws
(+K3
(+K3
×
5)
qs
connector
(CN402)
(CN402)
q;
connector
(SW600)
(SW600)
qd
front panel section
9
2
antenna cover cabinet
8
claw
Ver 1.1 2002.07