Sony CMT-EP313 / HCD-EP313 Service Manual ▷ View online
9
HCD-EP313
3-4. CONTROL Board, BACK LIGHT Board
3-5. Tape Mechanism Deck
1
volume knob
5
CONTROL board
3
nine screws
(+BVTP 3
(+BVTP 3
×
8)
2
screw
(+BVTP 3
(+BVTP 3
×
10)
4
wire (flat type)
21p (CN301)
21p (CN301)
6
two claws
7
connector
2p (CN305)
2p (CN305)
8
BACK LIGHT
board
board
3
two screws
(+BVTP 3
(+BVTP 3
×
10)
2
screw
(+BVTP 3
(+BVTP 3
×
10)
4
tape mechanism deck
1
Open the cassette door.
10
HCD-EP313
3-6. Cassette Door Assy
3-7. MAIN Board, POWER Board
1
two claws
2
cassette door assy
7
two cushions
4
PT PWB cover
2
screw
(+BVTP 3
(+BVTP 3
×
8)
5
four screws
(+BVTP 4
(+BVTP 4
×
12)
6
shield plate trans
3
MAIN board
8
POWER board
1
connector
6p (CN901)
6p (CN901)
11
HCD-EP313
2
two screws
(+PWH 2.6
(+PWH 2.6
×
10)
9
screw
(+P 2
(+P 2
×
5)
7
two cushion
rubbers
rubbers
8
four remove soldrings.
6
two cushion
rubbers
rubbers
3
two screws
(+PWH 2.6
(+PWH 2.6
×
10)
1
CD deck cover
4
three claws
5
panel CD
qa
CD board
qs
CD mechanism deck
(KSM-213EDP)
(KSM-213EDP)
q;
wire (flat type)
16p (CN102)
16p (CN102)
2
gear (A)
1
claw
5
sled shaft
6
KSS-213E/C2N
4
3
3-8. CD Mechanism Deck (KSM-213EDP)
3-9. Optical Pick-up (KSS-213E/C2N)
12
HCD-EP313
2.94 – 7.84 mN • m
(30 to 79 g • cm)
(0.42 – 1.11 oz • inch)
0.15 – 0.59 mN • m
(2 to 6 g • cm)
(0.03 – 0.08 oz • inch)
0.15 – 0.59 mN • m
(2 to 6 g • cm)
(0.03 – 0.08 oz • inch)
0.15 – 0.59 mN • m
(2 to 6 g • cm)
(0.03 – 0.08 oz • inch)
6.86 – 17.64 mN • m
(70 to 179 g • cm)
(0.98 – 2.49 oz • inch)
9.8 mN • m or more
(100 g • cm or more)
(1.4 oz • inch or more)
9.8 mN • m or more
(100 g • cm or more)
(1.4 oz • inch or more)
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Precaution
1.
Clean the following parts with a denatured alcohol-moistened
swab:
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2.
Demagnetize the record/playback head with a head demag-
netizer.
netizer.
3.
Do not use a magnetized screwdriver for the adjustments.
4.
After the adjustments, apply suitable locking compound to the
parts adjusted.
parts adjusted.
5.
The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
supply voltage unless otherwise noted.
Torque Measurement
Mode
FWD
FWD
back tension
back tension
REV
REV
back tension
back tension
FF/REW
FWD tension
REV tension
Torque meter
Meter reading
SECTION 4
MECHANICAL ADJUSTMENTS
Click on the first or last page to see other CMT-EP313 / HCD-EP313 service manuals if exist.