DOWNLOAD Sony CMT-DC1K / HCD-DC1K Service Manual ↓ Size: 4.71 MB | Pages: 47 in PDF or view online for FREE

10

2

belt (CDM55)

B

3

Pull the tray pushing 

B

.

4

two screws
(BTP2.6 

×

 6)

5

LOADING MOTOR board

1

Rotate the gear(B) in
the direction of arrow 

A

.

A

2

1

6

3

4

5

7

8

11

• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returning
the set to the customer.

Procedure:
1. Turn ON the power.
2. Press three buttons

x

(TAPE), 

x

(CD), and

[TUNER/BAND]

 simultaneously.

3. The set is reset.

Procedure:
1.

Set to standby state.

2.

Press three buttons of

x

(TAPE),

x

 (CD), and

[FUNCTION]

 simultaneously.

3.

Liquid crystal display are all turned on.

4.

To exit from this mode, press the

I/1

button to turn the power

OFF.

This mode can be used for operation check of tape deck section.

Procedure:
1.

Set a tape in the tape deck.

2.

Set to standby state.

3.

Press three buttons of

x

(TAPE),

x

 (CD), and 

[+]

 (TUNING)

simultaneously.

4.

The aging is executed in bellow sequence.

5.

To exit from the aging mode, press the

I/1

button to turn the

power OFF.

This mode can be used for operation check of CD section.

Procedure:
1.

Load a CD disc.

2.

Set to standby state.

3.

Press three buttons of

x

(TAPE),

x

(CD), and 

[--]

 ( TUNING)

simultaneously.

4.

The aging is executed in bellow sequence.

5.

To exit from the aging mode, press the

I/1

button to turn the

power OFF.

12

Confirm each contents of this section first of all. If the results are
not satisfied, do the adjustment.

1.

Demagnetize the record/playback head with a head
demagnetizer.

2.

Do not use a magnetized screwdriver for the adjustments.

3.

After the adjustments, apply suitable locking compound to the
parts adjust.

4.

The adjustments should be performed with the rated power
supply voltage unless otherwise noted.

5.

The adjustments should be performed in the order given in this
service manual.  (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)

6.

The adjustments should be performed for both L-CH and R-
CH.

7.

Switches and controls should be set as follows unless otherwise
specified.

• Test Tape

Procedure:
1.

Mode:  Playback

2.

Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.

3.

Mode: Playback

4.

Repeat step 1 to 3 in playback (REV) mode.

5.

After the adjustments, apply suitable locking compound to the
pats adjusted.

0 dB=0.775 V

Tape

Signal

Used for

P-4-A100

10 kHz, –10 dB

Azimuth Adjustment

°

°

°

°

13

1.

CD Block is basically constructed to operate without
adjustment.

2.

Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.

3.

Use an oscilloscope with more than 10 M

Ω

 impedance.

4.

Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with the
following checks.

5.

Check the focus bias check when optical block is replaced.

Procedure :
1.

Connect oscilloscope to TP (RF) and TP (VC) on the CD board.

2.

Press the

I/1

button to turn the power on, and press the

Z

(CD) button to open the CD disc tray.

3.

Put disc (YEDS-18) in and press the

u

(CD) button to play-

back.

4.

Confirm that oscilloscope waveform is as shown in the figure
below. (eye pattern)
A good eye pattern means that the diamond shape ( 

 

) in the

center of the waveform can be clearly distinguished.

±

s