Sony CMT-CPX1 / HCD-CPX1 (serv.man2) Service Manual ▷ View online
5
HCD-CPX1
TAPE MECHANICAL DECK SERVICE POSITION
Set up the service position with putting an insulator under the mechanical deck as the figure shown below.
tape mechanical deck
insulator
CD MECHANISM DECK SERVICE POSITION
Set up the service position for the CD mechanism deck with disassembling the entire set as the figure shown below.
AMP section
CD mechanism deck
main board
front panel
6
HCD-CPX1
NOTE ON LEADING THE WIRE (FLAT TYPE) (9 CORE)
Lead the wire (flat type) (9 core) properly to prevent the wire from coming out from the right side of the guides on the sub panel or sagging
inside of the lid.
inside of the lid.
NOTE ON INSTALLING THE HP BOARD
Note:
Follow the assembly procedure in the numerical order given.
lid (TC)
guides
wire (flat type) (9 core)
sub panel
3
three screws
(BVTP2.6
(BVTP2.6
×
8)
1
Lead the cable trough out
the ditch of the HP board
to prevent the cable from
contacting with the CD
mechanism deck.
the ditch of the HP board
to prevent the cable from
contacting with the CD
mechanism deck.
2
HP board
ditch
cable
HP board
7
HCD-CPX1
CLINCHING THE WIRE (FLAT TYPE) (21 CORE)
HANDLING TWO CABLES FROM THE SUB POWER AND THE SWITCHING REGULATOR TO THE MAIN BOARD
heat sink
AMP board
Clinch the wire (flat type) (21 core)
to prevent the wire from contacting with
the heat sink of the AMP board.
to prevent the wire from contacting with
the heat sink of the AMP board.
cable from the switching
regulator to the main board
regulator to the main board
lead pin
cable from the sub power
to the main board
to the main board
fabric no woven (10 – 20)
Note: Do not reuse the current fabric
Note: Do not reuse the current fabric
because it may fall off.
Note: Fix two cables with the lead pin and the fabric non woven (10 – 20),
or they may sag and contact with the CD mechanism deck.
8
HCD-CPX1
SECTION 2
GENERAL
• LOCATION OF CONTROLS
– Front View –
This section is extracted from
instruction manual.
instruction manual.
BASS +/– wa
CD SYNCHRO qa
Disc tray ql
DISPLAY wf
Disc tray ql
DISPLAY wf
Display window 3
DSG ws
FM MODE qs
DSG ws
FM MODE qs
FUNCTION 0
PHONES jack qk
PLAY MODE/DIRECTION wd
PHONES jack qk
PLAY MODE/DIRECTION wd
Remote sensor 2
REPEAT qs
TREBLE +/– w;
REPEAT qs
TREBLE +/– w;
TUNER/BAND 9
TUNING MODE wd
TUNING +/– qd
TUNING MODE wd
TUNING +/– qd
VOLUME +/– qf
?/1 (power) 1
TAPE
TAPE
Z (eject) 4
TAPE
nN (play) 5
TAPE
x (stop) 6
TAPE
X (pause) 7
TAPE
z REC (record) 8
lm/ML (rewind/fast
forward, go back/go forward)
qd
qd
CD
NX (play pause) qg
CD
x (stop) qh
CD
Z (eject) qj
ALPHABETICAL ORDER
A – Q
R – Z
BUTTON DESCRIPTIONS
1
qa
qs
0
5
6
7
8
9
qg
qd
qh
qj
2
3
4
qf
w;
ql
qk
wa
ws
wd
wf
Click on the first or last page to see other CMT-CPX1 / HCD-CPX1 (serv.man2) service manuals if exist.