Sony CMT-CP101 / CMT-CP101K / HCD-CP101 Service Manual ▷ View online
4
HCD-CP101
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
• MODEL IDENTIFICATION
– Rear Panel –
– Rear Panel –
Power Voltage Indication
Power Voltage
Incdication
AC: 120 V 60 Hz 75 W
AC: 230 V -50/60 Hz 75 W
AC: 110 – 120/
220 – 240 V / 50/60 Hz 75 W
Model
US, Canadian and
Mexican models
AEP, UK, Korean and
Australian models
E, Singapore and
Argentina models
SERVICE POSITION
In checking the CD block, prepare jig (extension cable J-2501-
011-B: 1.25 mm Pitch, 19 cores, Length 300 mm).
011-B: 1.25 mm Pitch, 19 cores, Length 300 mm).
Connect jig (extension cable J-2501-011-B)
to the MAIN board (CN101) and CD board (CN101).
to the MAIN board (CN101) and CD board (CN101).
MAIN board
CD board
Ver 1.2
5
HCD-CP101
SECTION 2
GENERAL
• LOCATION OF CONTROLS
– Front View –
BASS wd (15)
CD EJECT Z qg (8)
CD SYNC qa (13, 14)
CD u qj (8, 9)
CD x qh (8–10, 18, 20)
CD ./> qk (8, 9)
CD m/M qk (8)
DSG 3 (15)
FUNCTION 2 (8–10, 12, 13, 18)
PHONES jack wf
PLAY MODE w; (8, 9, 14)
Remote sensor wa
REPEAT ql (8)
CD EJECT Z qg (8)
CD SYNC qa (13, 14)
CD u qj (8, 9)
CD x qh (8–10, 18, 20)
CD ./> qk (8, 9)
CD m/M qk (8)
DSG 3 (15)
FUNCTION 2 (8–10, 12, 13, 18)
PHONES jack wf
PLAY MODE w; (8, 9, 14)
Remote sensor wa
REPEAT ql (8)
TAPE EJECT Z 6 (12)
TAPE z REC 5
TAPE z REC 5
(
13)
TAPE Y 8 (12–14)
TAPE X 0 (12–14)
TAPE x 7 (12–14, 20)
TAPE m/M 9 (12)
TREBLE ws (15)
TUNER BAND qs (9, 10, 20)
TUNING MODE qf (9–11)
TUNING +/– qd (9–11)
VOLUME 4 (17)
TAPE X 0 (12–14)
TAPE x 7 (12–14, 20)
TAPE m/M 9 (12)
TREBLE ws (15)
TUNER BAND qs (9, 10, 20)
TUNING MODE qf (9–11)
TUNING +/– qd (9–11)
VOLUME 4 (17)
Z
x
Y
?/1
m
M
z
X
Z
x
u
.
>
m
M
1
7
6
8
9
qs
qd
qg
qh
0
5
2
3
4
qj
qk
ql
w;
wa
ws
wd
wf
qa
qf
@/1 (power) 1 (7, 10, 15, 17)
This section is extracted from
instruction manual.
instruction manual.
6
HCD-CP101
1
2
3
8
5
6
4
9
0
qa
qs
qd
qj
qk
qh
qg
qf
ql
w;
wa
ws
7
CD REPEAT qk (8)
CD N ws (8, 9)
DIR MODE ql (12–14)
DISPLAY 2 (11, 16)
DSG 1 (15)
ENTER qd (7, 10, 15, 17)
FM MODE 9 (11)
FUNCTION qj (8–10, 12, 13,
CD N ws (8, 9)
DIR MODE ql (12–14)
DISPLAY 2 (11, 16)
DSG 1 (15)
ENTER qd (7, 10, 15, 17)
FM MODE 9 (11)
FUNCTION qj (8–10, 12, 13,
18)
MEMORY qh (10)
SLEEP qf (16)
TAPE Y w; (12–14)
TIMER SELECT qs (15, 17)
TIMER SET qg (7, 14, 17)
TUNER/BAND wa (10)
TUNING MODE/PLAY MODE
TAPE Y w; (12–14)
TIMER SELECT qs (15, 17)
TIMER SET qg (7, 14, 17)
TUNER/BAND wa (10)
TUNING MODE/PLAY MODE
q;
(8, 9, 10, 11, 14)
VOL +/– qa (17)
X 4 (8, 12–14)
x 5 (8, 9, 12–14)
./> 6 (7–10, 14, 15, 17)
m/M 7 (8, 10–12)
@/1 (power) 3 (7, 15, 17)
z REC 8 (13)
x 5 (8, 9, 12–14)
./> 6 (7–10, 14, 15, 17)
m/M 7 (8, 10–12)
@/1 (power) 3 (7, 15, 17)
z REC 8 (13)
– Remote Control –
Setting the clock
1
Turn on the system.
2
Press TIMER SET on the remote.
3
Press
.
/
>
on the remote
repeatedly to set the hour.
4
Press ENTER on the remote.
The minute indication flashes.
5
Press
.
/
>
on the remote
repeatedly to set the minute.
6
Press ENTER on the remote.
The clock will begin operating.
To adjust the clock
1
Press TIMER SET on the remote.
2
Press . or > on the remote to select
“SET CLOCK”, then press ENTER on the
remote.
“SET CLOCK”, then press ENTER on the
remote.
3
Do the same procedures as step 3 to 6
above.
HCD-CP101
7
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. COVER (UPPER)
(Page 8)
Set
3-4. FRONT PANEL SECTION
(Page 9)
3-3. CD LID SUB ASSY
(Page 8)
3-5. TAPE MECHANISM DECK
(Page 9)
3-7. BASE UNIT
(BU-K6BD41A)
(Page 10)
3-8. MOTOR BOARD
(Page 11)
3-9. CAM (CDM55)
(Page 11)
3-6. CD MECHANISM DECK
(CDM55F-K6BD41A)
(Page 10)