Sony CFS-929S Service Manual ▷ View online
6
CFS-929S
2-5. MECHANISM DECK
2-4. H/P, LED2, MAXI BASS, VOL, MAIN BOARDS
8
knob (VOLUME)
qk
claws
ql
claws
claws
9
BVTP 3x10
qf
BVTP 3x12
qs
BVTP 3x10
wl
VOL board
qg
BVTP 3x10
qh
BVTP 3x10
1
CNP310
2
CNP309
7
CNP305
6
CNP304
5
CNP302
4
CNP301
3
CNP303
qj
BVTP 3x12
w;
MAIN board
wf
MAXI BASS board
wg
button (MAXI BASS)
qd
LED2 board
ws
CNP308
wa
CNP417
0
retainer board
wd
retainer board
qa
H/P board
3
BVTP 3x10
4
BVTP 3x10
5
BVTP 3x10
6
mechanism deck
1
2
7
CFS-929S
2-7. REC SW BOARD, BELT, MOTOR ASSY (W) (M301)
2-6. JOG, LED1 BOARDS
4
BVTP 3x10
5
LED1 board
6
window (LED)
2
BVTP 3x10
3
JOG board
1
jog dial
1
PTT 2x6
2
REC SW board
9
motor screw
deck A
deck B
5
PTT 2x5
7
PTT 2x5
3
PTT 2x5
0
motor assy (M301)
6
bracket
8
chassis (joint)
4
sssss
qa
belt
qs
belt
8
CFS-929S
SECTION 3
DIAL POINTER SETTING
UP
pointer
knob (TUNING) assy
knob (TUNING) assy
1
pointer
2
knob (TUNING) assy
3
midway gear
midway gear
4
PTPWH 3x10
4
TUNER board
8
F/T board
1
gear (VC)
2
5
BVTP 3x10
3
6
BVTP 3x10
7
BVTP 3x10
9
BVTP 3x10
9
CFS-929S
PRECAUTION
1. Clean the following parts with a denatured alcohol-moistened
swab :
record/playback head
pinch roller
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagne-
tizer. (Do not bring the head demagnetizer close to the erase
head.)
head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
6. Power supply voltage: 12 V dc.
Torque Measurement DECK A DECK B
Mode
Torque meter
Meter reading
2.21 to 5.39 mN • m
Forward
CQ-102C
22.5 to 55 g • cm
(0.31 to 0.76 oz • inch)
Forward
0.20 to 0.49 mN • m
back tension
CQ-102C
2 to 5 g • cm
(0.03 to 0.07 oz • inch)
Fast Forward
5.89 to 11.76 mN • m
and
CQ-201B
60 to 120 g • cm
Rewind
(0.83 to 1.67 oz • inch)
Tape Tension Measurement DECK A DECK B
Mode
Tension meter
Meter reading
Forward
CQ-403A
more than 150 g
(more than 5.29 oz)
SECTION 5
ELECTRICAL ADJUSTMENTS
SECTION 4
MECHANICAL ADJUSTMENTS
TAPE SECTION 0 dB = 0.775 V
Standard Output Level
Output terminal
SP OUT
PHONES OUT
load impedance
4
Ω
32
Ω
output signal level
0.775 V (0 dB)
0.25 V (–10 dB)
Test Tape
Tape
Signal
Used for
WS-48A
3 kHz, 0 dB
tape speed adjustment
Tape Speed Adjustment DECK A DECK B
Procedure:
• Perform normal speed adjustment before high speed check.
Mode: playback (deck A)
Procedure:
• Perform normal speed adjustment before high speed check.
Mode: playback (deck A)
record (deck B)
Deck
Tape
Adjustment
Frequency
speed
point
counter
A
Normal (playback)
RV302
3,000 to 3,030 Hz
A
HI-SPEED DUBBING
(confirmation) 5,300 to 6,300 Hz
(playback)
B
HI-SPEED DUBBING
———
———
(record)
Frequency difference between the beginning and the end of the
tape should be within ± 1.0% (both Normal and Hi-speed).
tape should be within ± 1.0% (both Normal and Hi-speed).
Adjustment Location: – main board (component side) –
PHONES jack (J301)
set
32
Ω
test tape
WS-48A
(3 kHz, 0 dB)
WS-48A
(3 kHz, 0 dB)
digital frequency
counter
counter
Adjust RV301 so that reading on digital frequency counter
becomes 3,000 Hz.
Specification Value:
RV302
– MAIN board (component side) –
Click on the first or last page to see other CFS-929S service manuals if exist.