Sony CFS-515L Service Manual ▷ View online
– 5 –
2-4. MECHANISM DECK, REC SW BOARD
2-5. CHASSIS SUB ASSY, BELT
2
Screw (+PTT 2x5)
1
3
Deck B
2
Screws (+PTT 2x5)
4
Belt
4
Belt
2
Screws (+PTT 2x5)
Deck A
Flywheel assy
Chassis sub assy
Flywheel assy
3
Screws
(+BTP 3x10)
3
Screws
(+BTP 3x10)
5
Screw
(+PTT 2x6)
6
4
1
2
1
Button (ST/EJ)
Cassette lid (L)
REC SW board
Cassette lid (R)
Mechanism deck section
Button (ST/EJ)
Cabinet (Front) section
2
– 6 –
2-6. VOL BOARD, MAIN BOARD, ECM BOARD
2-7. TUNER BOARD
5
3
6
4
Screws (+BVTP 3x10)
1
Screw (+BTP 3x10)
1
Screw (+BTP 3x10)
2
Knob (F/T)
Chassis (Tune)
Tuner board
Tuner board
Claw
7
1
3
3
4
8
5
Screw (+BTP 3x10)
6
Screw (+BVTP 3x6)
2
Screw
(+BTP 3x10)
Knob (VOL)
VOL board
Main board
ECM board
– 7 –
SECTION 3
DIAL POINTER INSTALLATION
Cabinet (Front)
Cabinet (Front)
Knob (Tune)
1
Pointer
a
c
b
Pointer
Marked line
2
– 1
2
– 2
6
Screw (+BTP 3x10)
6
Screw (+BTP 3x10)
5
Screws (+BVTP 3x10)
Cabinet (Front)
4
Gear (Midway)
3
Gear (VC)
Chassis (Tune)
Tuner board
1 Set the pointer into the grooves of the cabinet
(Front) in the order of
a, b and c.
2 Turn the knob (Tune) in the direction of the arrow,
then set the pointer by aligning it with the marked
line of the cabinet (Front).
line of the cabinet (Front).
3 Turn the gear (VC) fully counterclockwise.
4 Turn the gear (Midway) fully clockwise.
5 Mount the tuner board to the chassis and tighten
4 Turn the gear (Midway) fully clockwise.
5 Mount the tuner board to the chassis and tighten
with screws.
6 Mount the chassis (Tune) to the cabinet (Front) and
tighten with screws.
Note :
Follow the installation procedure in the numerical order given.
– 8 –
SECTION 4
ADJUSTMENTS
4-1. MECHANICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head
playback head
pinch roller
erase head
rubber belt
capstan
2. Demagnetize the record/playback head with a head demagne-
tizer. (Do not bring the head demagnetizer close to the erase
head.)
head.)
3. Do not use a magnetized screwdriver for adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
Torque Measurement
Torque
Torque Meter
Meter Reading
Playback
CQ-102C
18 – 60 g • cm
(0.25 – 0.83 oz• inch)
Back Tension
CQ-102C
1 – 5 g • cm
(0.014 – 0.069 oz• inch)
Rewind
CQ-201B
45 – 95 g • cm
Fast Forward
(0.63 – 1.31 oz• inch)
Tape Tension Measurement
Mode
Tension Meter
Meter Reading
FWD
CQ-403A
more than 60g (2.12 oz)
4-2. ELECTRICAL ADJUSTMENTS
TAPE SECTION
1. The adjustments should be performed in the order give in the
service manual. (As a general rule, playbak circuit adjustment
should be completed before performing recording circuit adjust-
ment.)
should be completed before performing recording circuit adjust-
ment.)
2. The adjustments should be performed for both L-CH and R-CH
unless otherwise indicated.
• Switch location
FUNCTION switch
• • • • • • • • • • • • • • • • •
TAPE (RADIO OFF)
PRESET MODE
• • • • • • • • • • • • • • • • • • • • •
MANUAL
GRAPHIC EQUALIZER
• • • • • • • •
center click
BALANCE
• • • • • • • • • • • • • • • • • • • • • • • • • • • • •
center click
VOLUME
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
MAX
MEGA BASS
• • • • • • • • • • • • • • • • • • • • • • • • •
mechanical center
Standard Output Level
Output terminal
PHONES
SP (FRONT) OUT
Load impedance
32
Ω
6
Ω
Output signal level
0.25V (–10dB)
0.775V (0dB)
Test Tape
Type
Signal
Used for
WS-48A
3kHz, 0dB
Tape Speed Adjustment
0dB=0.775V
Tape Speed Adjustment
Procedure :
Mode : Playback
(Normal speed)
1. Deck A to playback mode.
2. Adjust the RV303 for 2,985 – 3,015Hz reading on digital fre-
1. Deck A to playback mode.
2. Adjust the RV303 for 2,985 – 3,015Hz reading on digital fre-
quency counter.
3. Frequency difference between the beginning and the end of the
tape should be within 1% (30Hz).
(High speed)
4. Deck B to record mode.
5. Deck A to high speed playback mode.
6. Confirm that the reading of the digital voltmeter becomes 5,500
4. Deck B to record mode.
5. Deck A to high speed playback mode.
6. Confirm that the reading of the digital voltmeter becomes 5,500
– 6,500Hz.
7. Frequency difference between the beginning and the end of the
tape should be within 1% (30Hz).
Adjustment Location :
set
test tape
WS-48A
(3kHz, 0dB)
WS-48A
(3kHz, 0dB)
32
Ω
digital frequency
counter
phones jack
IC201
RV303 : Tape Speed Adjustment
[ MAIN BOARD ]
(Component side)
(Component side)
Click on the first or last page to see other CFS-515L service manuals if exist.