Sony CFD-S26L / CFD-S36L Service Manual ▷ View online
4
CFD-S26L/S36L
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
SECTION 1
SERVICING NOTES
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Turn ON the POWER button and press FUNCTION button to
CHECK
1. Turn ON the POWER button and press FUNCTION button to
CD position.
2. Open the lid (CD).
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the CD N X button.
5. Confirm the laser diode emission while observing the objecting
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the CD N X button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
S801
5
CFD-S26L/S36L
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
REC PLAY REW FF STOP/EJECT PAUSE
VOLUME +,–
MEGA Xpand
(CFD-S36L only)
(CFD-S36L only)
MEGA BASS
Z
PUSH
OPEN/CLOSE
CD
compartment
compartment
Number buttons for
CD/RADIO DIRECT OPERATION
CD/RADIO DIRECT OPERATION
Tape
compartment
compartment
OPERATE
SLEEP
N X
x
CD
TAPE
RADIO BAND•
AUTO PRESET
AUTO PRESET
Remote sensor
(CFD-S36L only)
(CFD-S36L only)
Display
OPR/BATT
indicator
indicator
MODE
i
(headphones) jack
DISPLAY ENT•
MEMORY
MEMORY
TUNE –, +
.
.
,>
Remote Control (CFD-S36L only)
Location of controls
SLEEP
FUNCTION
Number buttons
MODE
TUNE +,–
BAND
N
MEGA Xpand
OPERATE
VOL +,–
x
X
MEGA BASS
.
,>
Tip
To listen through headphones, connect the headphones to the i (headphones) jack.
To listen through headphones, connect the headphones to the i (headphones) jack.
VOL
TUNE
–
MEGA Xpand
MEGA BASS
BAND
TUNE
+
POWER
7
8
9
MODE
0/10
>
10
1
FUNCTION SLEEP
CD/RADIO
(AC ONLY)
2
3
4
5
6
6
CFD-S26L/S36L
• The equipment can be removed using the following procedure.
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (FRONT) SUB ASSY
Set
Cabinet (Front) Sub Assy
Wires
Tape Mechanism Block
Main Board
Belt,M801(Capstan/Reel Motor),
HRP301 (Head, Magnetic)
HRP301 (Head, Magnetic)
CD Mechanism Block
Holder Assy, Cassette
PRE Board
Optical Pick-up
Cabinet (Upper) Assy
Power (1) Board, Power (2) Board
1
lid, battery case
2
BVTP 3x12
5
BVTP 3x12
4
BVTP 3x12
6
BVTP 3x12
3
BVTP 3x12
lid (CD)
7
CNP323
8
CNP805
9
cabinet (front) sub assy
7
CFD-S26L/S36L
3-2. WIRES
3-3. POWER (1) BOARD, POWER (2) BOARD
Put flat cable and wires between the cabinets and push them in the
grooves located at A to E in the figure to prevent disconnection
before assembling the set.
grooves located at A to E in the figure to prevent disconnection
before assembling the set.
CABINET (REAR)
CABINET (FRONT)
A
B
E
from speaker
from MAIN board
from CONTROL (1) board
C
D
1
BVTP 3x10
2
BVTP 3x10
5
CNP901
6
CNP902
4
7
POWER (1) board
POWER (2) board
3
BVTP 3x10