Sony CFD-S26 Service Manual ▷ View online
6
CFD-S26
– BATTERY TERMINAL (1) BOARD (component side) –
BATTERY TERMINAL (1) Board Part No.
Former type : 1-679-964-12
New type : 1-679-964-14
Former type : 1-679-964-12
New type : 1-679-964-14
– BATTERY TERMINAL (2) BOARD (component side) –
BATTERY TERMINAL (2) Board Part No.
Former type : 1-679-965-12
New type : 1-679-965-14
Former type : 1-679-965-12
New type : 1-679-965-14
– POWER (1) BOARD (component side) –
POWER (1) Board Part No.
Former type : 1-679-969-12
New type : 1-679-969-14
Former type : 1-679-969-12
New type : 1-679-969-14
– POWER (2) BOARD (component side) –
POWER (2) Board Part No.
Former type : 1-679-970-12
New type : 1-679-970-14
Former type : 1-679-970-12
New type : 1-679-970-14
7
CFD-S26
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
REC PLAY REW FF STOP/EJECT PAUSE
VOLUME +,–
MEGA BASS
Z
PUSH
OPEN/CLOSE
CD
compartment
compartment
Number buttons for
CD/RADIO DIRECT OPERATION
CD/RADIO DIRECT OPERATION
Tape
compartment
compartment
POWER
SLEEP
N X
x
CD
TAPE
RADIO BAND•
AUTO PRESET
AUTO PRESET
Display
OPR/BATT
indicator
indicator
MODE
i
(headphones) jack
DISPLAY ENT•
MEMORY
MEMORY
TUNE –, +
.
.
,>
Location of controls
Tip
To listen through headphones, connect the headphones to the i (headphones) jack.
To listen through headphones, connect the headphones to the i (headphones) jack.
8
CFD-S26
• The equipment can be removed using the following procedure.
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (FRONT) SUB ASSY
Set
Cabinet (Front) Sub Assy
Wires
Tape Mechanism Block
Main Board
Belt,M801(Capstan/Reel Motor),
HRP301 (Head, Magnetic)
HRP301 (Head, Magnetic)
CD Mechanism Block
Holder Assy, Cassette
PRE Board
Optical Pick-up
Cabinet (Upper) Assy
Power (1) Board, Power (2) Board
Voltage Select Board
1
lid, battery case
2
BVTP 3x12
5
BVTP 3x12
4
BVTP 3x12
6
BVTP 3x12
3
BVTP 3x12
lid (CD)
7
CNP323
8
CNP805
9
cabinet (front) sub assy
9
CFD-S26
3-2. WIRES
3-3. POWER (1) BOARD, POWER (2) BOARD
Put flat cable and wires between the cabinets and push them in the
grooves located at A to E in the figure to prevent disconnection
before assembling the set.
grooves located at A to E in the figure to prevent disconnection
before assembling the set.
CABINET (REAR)
CABINET (FRONT)
A
B
E
from speaker
from MAIN board
from CONTROL (1) board
C
D
1
BVTP 3x10
2
BVTP 3x10
5
CNP901
6
CNP902
4
7
POWER (1) board
POWER (2) board
3
BVTP 3x10
Click on the first or last page to see other CFD-S26 service manuals if exist.