Sony CFD-S22 / CFD-S32 Service Manual ▷ View online
– 5 –
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Reinforcing the bass sound
Press MEGA BASS.
"MEGA BASS" appears in the display.
To return to normal sound, press the button again.
Adjusting
the tone (CFD-S32only)
Press TONE.
To enhance
the high tone
the low tone
Tape compartment
MEGA BASS
Z
PUSH OPEN/CLOSE
CD compartment
VOLUME +,–
TUNING –,+
DISPLAY ENT
MEMORY
MEMORY
PLAY MODE
MONO/ST
MONO/ST
TONE
Location of controls
Adjusting the sound emphasis (MEGA BASS/TONE)
i
(headphones) jack
Number buttons for
CD/RADIO DIRECT OPERATION
CD/RADIO DIRECT OPERATION
x
BX
.
,
>
POWER
SLEEP
CD
TAPE
RADIO BAND
AUTO PRESET
AUTO PRESET
Display
HI
LO
Tip
To listen through headphones, connect the headphones to the
i (headphones) jack.
i (headphones) jack.
POWER
SLEEP
FUNCTION
Number buttons
MODE*
BAND
TUNE +,–
VOL +,–
x
X
N
.
,
>
LOOP
FLASH
TONE (CFD-S32only)
MEGA BASS
Remote Control (CFD-S32only)
* MODE on the remote has same function as
PLAY MODE•MONO/ST on the player.
PLAY MODE•MONO/ST on the player.
OPR/BATT
indicator
indicator
– 6 –
1
Press CD (direct power-on).
3
Close the CD compartment.
4
Press u (N on the remote, CFD-S32 only).
The player plays all the tracks once.
The player plays all the tracks once.
Track number
Playing time
To
adjust the volume
stop playback
pause playback
go to the next track
go back to the previous track
remove the CD
turn on/off the player
c
Playing a CD
Press
VOLUME +, – (VOL +, – on the remote,
CFD-S32 only)
CFD-S32 only)
x
u (X on the remote, CFD-S32 only)
Press the button again to resume play after
pause.
Press the button again to resume play after
pause.
>
.
Z PUSH OPEN/CLOSE
POWER
1
Press RADIO BAND•AUTO PRESET until the band you
want appears in the display (direct power-on).
Each time you press the button, the indication changes as
follows: “FM1” t “FM2” t “AM”.
want appears in the display (direct power-on).
Each time you press the button, the indication changes as
follows: “FM1” t “FM2” t “AM”.
2
Hold down TUNING + or – (TUNE + or – on the remote,
CFD-S32 only) until the frequency digits begin to change
in the display.
CFD-S32 only) until the frequency digits begin to change
in the display.
The player automatically scans the radio frequencies and
stops when it finds a clear station.
If you can't tune in a station, press the button repeatedly
to change the frequency step by step.
stops when it finds a clear station.
If you can't tune in a station, press the button repeatedly
to change the frequency step by step.
To
adjust the volume
turn on/off the radio
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself for AM.
FM
AM
Tips
• The "FM1" and "FM2" bands have the same functions. You can store
the stations you want separately in "FM1" and "FM2".
• If the FM broadcast is noisy, press PLAY MODE•MONO/ST until
"Mono" appears in the display and the radio will play in monaural.
Listening to the radio
Press
VOLUME +, – (VOL +, – on the remote,
CFD-S32 only)
CFD-S32 only)
POWER
Display
Display
2
Press Z PUSH OPEN/CLOSE down to open the CD
compartment and place a CD in the CD compartment.
compartment and place a CD in the CD compartment.
With the labeled side up
c
Display
– 7 –
Use TYPE I (normal) tape only.
1
Press TAPE (direct power-on).
2
Press xZ to open the tape compartment and insert a
recorded tape. Close the compartment.
recorded tape. Close the compartment.
3
Press N.
With the side you want to
play facing upward
play facing upward
2
Select the program source you want to record.
To record from the CD player
Press CD and insert a CD (See "Playing a CD").
To record from the radio
Press RADIO BAND•AUTO PRESET and tune in the
station you want (See "Listening to the radio").
station you want (See "Listening to the radio").
3
Press z to start recording.
(N is depressed automatically).
(N is depressed automatically).
1
Press xZ to open the tape compartment and insert a
blank tape.
blank tape.
With the side you want to
record on facing upward
record on facing upward
To
stop recording
pause recording
turn on/off the player
POWER
Tips
• Adjusting the volume or the audio emphasis will not affect the
recording level.
• For the best results, use the AC power as a power source for recording.
• To erase a recording, proceed as follows:
• To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press TAPE.
3 Press z.
2 Press TAPE.
3 Press z.
To
adjust the volume
stop playback
fast-forward or rewind the tape
pause playback
eject the cassette
turn on/off the player
Notes on cassettes
• Break off the cassette tab from side A or B to prevent accidental
recording. If you want to reuse the tape for recording, cover the broken
tab with adhesive tape.
tab with adhesive tape.
• The use of a cassette with more than 90 minutes of play time is not
recommended except for
long,
continuous recording or
playback.
Tab for side B
Tab for side A
Side A
c
c
Use TYPE I (normal) tape only.
Recording
Playing a tape
Press
VOLUME +, – (VOL +, – on the
remote, CFD-S32 only)
remote, CFD-S32 only)
xZ
M or m
X
Press the button again to resume play
after pause.
after pause.
xZ
POWER
Press
xZ
X
Press the button again to resume recording.
Display
Display
Display
– 8 –
• The equipment can be removed using the following procedure.
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
1
lid, battery case
2
BVTP 3x10
3
BVTP 3x10
4
BVTP 3x12
6
BVTP 3x12
5
BVTP 3x10
lid (CD)
7
CNP323
8
CNP501
9
cabinet (front) sub assy
3-1. CABINET (FRONT) SUB ASSY
Set
Cabinet (Front) Sub Assy
Wires
Tape Mechanism Block
Main Board
CD Mechanism Block
Holder Assy, Cassette
PRE Board
Cabinet (Upper) Assy
Secondary, Power Board
Tuner Board
VOL SEL Board
Click on the first or last page to see other CFD-S22 / CFD-S32 service manuals if exist.