DOWNLOAD Sony CFD-S20CP Service Manual ↓ Size: 5.54 MB | Pages: 55 in PDF or view online for FREE

1

Other Specifications
CD player section
System

Compact disc digital audio system

Laser diode properties

Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 

µW

(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm) (CLV)

Number of channels

2

Frequency response

20 - 20,000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

– Continued on next page –

Radio section
Frequency range

FM: 87.5 - 108 MHz
AM: 530 - 1,710 kHz (US, CND)
AM: 531 - 1,611 kHz (KR, TW)

Antennas

FM: Telescopic antenna
AM: Built-in ferrite bar antenna

Cassette-corder section
Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 sec. with Sony cassette C-60

Frequency response

TYPE I (normal): 80 - 10,000 Hz

2006C04-1

© 2006.03

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 6,300 Hz; rated 1.8 W per channel-
minimum RMS power, with no more than 10%
total harmonic distortion in AC operation.

US Model

Canadian Model

Taiwan Model

Korea Model

CD

Model Name Using Similar Mechanism CFD-S400/S500

Section

CD Mechanism Type

KSM-213RDP

Optical Pick-up Name

KSS-213R

TC

Model Name Using Similar Mechanism CFD-S400/S500

Section Tape Transport Mechanism Type

MF-S200

2

General
Speaker

Full range: 10 cm (4 in.) dia.,
3.2 ohms, cone type (2)

Outputs

Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones

Power output

2.3 W + 2.3 W (at 3.2 ohms, 10%
harmonic distortion)

Power requirements

For CD radio cassette-corder:
US, CND, TW model:
   120 V AC, 60 Hz
KR model:
   220 V AC, 60 Hz
9 V DC, 6 size D (R20) batteries
For remote control:
3 V DC, 2 size AA (R6) batteries

Battery life

For CD radio cassette-corder:

Sony R20P: approx. 13.5 h

Sony alkaline LR20: approx. 20 h
Tape playback

Sony R20P: approx. 7.5 h

Sony alkaline LR20: approx. 15 h
CD playback

Sony R20P: approx. 2.5 h

Sony alkaline LR20: approx. 7 h

Dimensions

Approx. 386 

× 166 × 252 mm (w/h/d)

(15 

1/4

 

× 6 

5/8

 

× 10 inches) (incl. projecting parts)

Mass

Approx. 3.3 kg (7 lb. 4 oz.) (incl. batteries)

Supplied accessories

AC power cord (1)
Remote control (RMT-CS20CPA) (1)

Design and specifications are subject to change without
notice.

COMPONENTS  IDENTIFIED  BY  MARK  0  OR  DOTTED  LINE
WITH  MARK  0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.

Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.

Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C during

repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE  DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

• Abbreviation

CND

: Canadian model

KR

: Korean model

TW

: Taiwan model

3

......................................................... 4

............................................................................ 5

3-1.   Cabinet Top Assy ................................................................ 7
3-2.   Cabinet Front Assy, Cabinet Rear Assy .............................. 7
3-3.   Wires ................................................................................... 8
3-4.   MD Block ............................................................................ 8
3-5.   Cassette Door Assy ............................................................. 9
3-6.   LCD Board, Control (4) Board ........................................... 9
3-7.   Main Board ....................................................................... 10
3-8.   Tuner Board ....................................................................... 10
3-9.   Power Board ...................................................................... 11
3-10. CD Lid ............................................................................... 11
3-11. CD Block Assy .................................................................. 12
3-12. Optical Pick-up ................................................................. 12
3-13. R/P Head (HRP301), TC Board ........................................ 13
3-14. Motor Assy (M801), Main Belt (B), Sub Belt (B) ............ 13

............................... 14

Tape Section .......................................................................... 14
Tuner Section ......................................................................... 15
CD Section ............................................................................ 16

6-1.   IC Pin Descriptions ........................................................... 17
6-2.   Circuit Boards Location .................................................... 19
6-3.   Block Diagram – CD Section – ......................................... 20
6-4.   Block Diagram – Main Section – ...................................... 21
6-5.   Printed Wiring Board – CD Section – ............................... 22
6-6.   Schematic Diagram – CD Section – .................................. 24
6-7.   Printed Wiring Board – Tuner Section – ........................... 25
6-8.   Schematic Diagram – Tuner Section – .............................. 26
6-9.   Printed Wiring Boards – Main Section – .......................... 27
6-10. Schematic Diagram – Main Section (1/2) – ...................... 28
6-11. Schematic Diagram – Main Section (2/2) – ...................... 29
6-12. Printed Wiring Board – TC Section – ............................... 30
6-13. Schematic Diagram – TC Section – .................................. 31
6-14. Printed Wiring Boards – Control Section – ....................... 32
6-15. Schematic Diagram – Control Section – ........................... 33
6-16. Printed Wiring Boards – Display Section – ...................... 34
6-17. Schematic Diagram – Display Section – ........................... 35
6-18. Printed Wiring Boards – Power Supply Section – ............ 36
6-19. Schematic Diagram – Power Supply Section – ................. 37
6-20. IC Block Diagrams ............................................................ 38

7-1.   Main Section ..................................................................... 40
7-2.   Cabinet Front Section ........................................................ 41
7-3.   Cabinet Top Section .......................................................... 42
7-4.   Cabinet Rear Section ......................................................... 43
7-5.   Tape Mechanism Section .................................................. 44
7-6.   CD Mechanism Section .................................................... 45

......................................... 46

SAFETY  CHECK-OUT (US MODEL)
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers’ instructions to use these
instruments.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are
suitable.  (See Fig. A)

1.5 k

Ω

0.15 

µ

F

AC
voltmeter
(0.75 V)

To Exposed Metal
Parts on Set

Earth Ground

4

On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1

1. Turn ON the [POWER] button and press [CD] button to

CD position.

2. Open the CD lid.
3. Turn on S801 with screwdriver, etc. as following figure.
4. Press the  N X  (CD) button.
5. Confirm the laser diode emission while observing the objecting

lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.

S801