Sony CFD-S03CP / CFD-S03CPL Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
Canadian Model
CFD-S03CP
AEP Model
CFD-S03CP/S03CPL
UK Model
E Model
Australian Model
CFD-S03CP
CD RADIO CASSETTE-CORDER
9-887-043-09
2009B00-1
© 2009.02
© 2009.02
Ver. 1.8 2009.02
SPECIFICATIONS
CFD-S03CP/S03CPL
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6
Laser output: Less than 44.6
µ
W
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on the
optical pick-up block with 7 mm aperture.)
about 200 mm from the objective lens surface on the
optical pick-up block with 7 mm aperture.)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
CND, E92, MX model:
AM: 530 - 1 710 kHz
TW model:
AM: 531 - 1 611 kHz
EXCEPT CND, E92, MX, TW model:
AM/MW: 531 - 1 611 kHz (9 kHz step)
CND, E92, MX model:
AM: 530 - 1 710 kHz
TW model:
AM: 531 - 1 611 kHz
EXCEPT CND, E92, MX, TW model:
AM/MW: 531 - 1 611 kHz (9 kHz step)
530 - 1 610 kHz (10 kHz step)
CFD-S03CPL:
LW: 153 - 279 kHz
LW: 153 - 279 kHz
IF
FM: 10.7 MHz
AM/MW/LW: 450 kHz
AM/MW/LW: 450 kHz
Antennas
FM: Telescopic antenna
AM/MW/LW: Built-in ferrite bar antenna
AM/MW/LW: Built-in ferrite bar antenna
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 150 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10 000 Hz
General
Speaker
Full range: 8 cm dia., 4
Ω
, cone type (2)
Outputs
Headphones jack (stereo minijack):
For 16 - 32
For 16 - 32
Ω
impedance headphones
Power output
1.7 W + 1.7 W (at 4
Ω
, 10% harmonic distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz (CND, E92, MX, TW model)
220 V AC, 60 Hz (KR model)
220 – 230 V AC, 50 Hz (AR model)
230 V AC, 50 Hz (EXCEPT E92, KR, MX, AR, TW model)
9 V DC, 6 R14 (size C) batteries
For remote control:
3 V DC, 2 R03 (size AAA) batteries
120 V AC, 60 Hz (CND, E92, MX, TW model)
220 V AC, 60 Hz (KR model)
220 – 230 V AC, 50 Hz (AR model)
230 V AC, 50 Hz (EXCEPT E92, KR, MX, AR, TW model)
9 V DC, 6 R14 (size C) batteries
For remote control:
3 V DC, 2 R03 (size AAA) batteries
CD
Model Name Using Similar Mechanism CFD-S01
Section
CD Mechanism Type
KSM-213CDP
Optical Pick-up Name
KSS-213C
TC
Model Name Using Similar Mechanism CFD-S01
Section Tape Transport Mechanism Type
MF-S01
– Continued on next page –
Photo: CFD-S03CP
2
CFD-S03CP/S03CPL
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
other than those specified herein may result in hazardous
radiation exposure.
Flexible Circuit Board Repairing
•
Keep the temperature of the soldering iron around 270˚C during
repairing.
repairing.
•
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering or
unsoldering.
unsoldering.
Notes on Chip Component Replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be damaged
by heat.
by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Notes on DualDiscs
A DualDisc is a two sided disc product which mates DVD recorded
material on one side with digital audio material on the other side.
However, since the audio material side does not conform to the
Compact Disc (CD) standard, playback on this product is not
guaranteed.
material on one side with digital audio material on the other side.
However, since the audio material side does not conform to the
Compact Disc (CD) standard, playback on this product is not
guaranteed.
Power consumption
AC 13 W (CND, E92, MX model)
AC 12 W (EXCEPT CND, E92, MX model)
AC 12 W (EXCEPT CND, E92, MX model)
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 6 h
Sony alkaline LR14: approx. 20 h
Tape playback
Sony R14P: approx. 3 h
Sony alkaline LR14: approx. 12 h
CD playback
Sony R14P: approx. 1.5 h
Sony alkaline LR14: approx. 4.5 h
Dimensions
Approx. 360
×
141
×
235 mm (w/h/d)
(incl. projecting parts)
Mass
Approx. 2.6 kg (incl. batteries)
Supplied accessory
AC power cord (1)
Remote control (1)
Remote control (1)
Design and specifications are subject to change
without notice.
without notice.
• Abbreviation
CND : Canadian model
E92
E92
: AC 120V area in E model
KR
: Korea model
MX
: Mexican model
AR
: Argentina model
TW
: Taiwan model
Ver. 1.2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
CFD-S03CP/S03CPL
TABLE OF CONTENTS
1.
SERVICING NOTES
................................................
4
2.
GENERAL
...................................................................
5
3.
DISASSEMBLY
3-1.
Cabinet (Rear) Assy .........................................................
7
3-2.
Cabinet (Front) Assy, Cabinet (Upper) Assy ...................
7
3-3.
Main Board ......................................................................
8
3-4.
CD Block Assy ................................................................
8
3-5.
BD83S Board ..................................................................
9
3-6.
Optical Pick-up ................................................................
9
3-7.
Panel Board ..................................................................... 10
3-8.
CD Lid ............................................................................. 10
3-9.
Tape Mechanism Block, Belt (1), Belt (2) ...................... 11
3-10. TC Board ......................................................................... 11
3-11. Key-1 Board, Key-2 Board .............................................. 12
3-12. Power Board .................................................................... 12
3-11. Key-1 Board, Key-2 Board .............................................. 12
3-12. Power Board .................................................................... 12
4.
MECHANICAL ADJUSTMENTS
......................... 13
5.
ELECTRICAL ADJUSTMENTS
Tape Section .................................................................... 13
Tuner Section ................................................................... 14
CD Section ...................................................................... 16
Tuner Section ................................................................... 14
CD Section ...................................................................... 16
6.
DIAGRAMS
6-1.
Block Diagram – CD Section – ....................................... 17
6-2.
Block Diagram – Main Section – .................................... 18
6-3.
Circuit Boards Location .................................................. 19
6-4.
Printed Wiring Board – BD83S Section – ....................... 20
6-5.
Schematic Diagram – BD83S Section – .......................... 21
6-6.
Printed Wiring Board – Main Section – .......................... 22
6-7.
Schematic Diagram – Main Section (1/3) – .................... 23
6-8.
Schematic Diagram – Main Section (2/3) – .................... 24
6-9.
Schematic Diagram – Main Section (3/3) – .................... 25
6-10. Printed Wiring Boards – TC Section – ............................ 26
6-11. Schematic Diagram – TC Section – ................................ 27
6-12. Printed Wiring Boards – Panel Section – ........................ 28
6-13. Schematic Diagram – Panel Section – ............................ 29
6-14. Printed Wiring Boards – Power Supply Section – ........... 30
6-15. Schematic Diagram – Power Supply Section – ............... 31
6-11. Schematic Diagram – TC Section – ................................ 27
6-12. Printed Wiring Boards – Panel Section – ........................ 28
6-13. Schematic Diagram – Panel Section – ............................ 29
6-14. Printed Wiring Boards – Power Supply Section – ........... 30
6-15. Schematic Diagram – Power Supply Section – ............... 31
7.
EXPLODED VIEWS
7-1.
Rear Cabinet Section ....................................................... 39
7-2.
Front Cabinet Section (1) ................................................ 40
7-3.
Front Cabinet Section (2) ................................................ 41
7-4.
Upper Cabinet Section (1) ............................................... 42
7-5.
Upper Cabinet Section (2) ............................................... 43
7-6.
CD Mechanism Section ................................................... 44
8.
ELECTRICAL PARTS LIST
.................................. 45
•
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
4
CFD-S03CP/S03CPL
Ref. No.
TYPE A
TYPE B
IC804
S-816A33AMC-BAI-T2-G
NO MOUNT
IC806
NO MOUNT
XC6202P332FR
R883
100k
NO MOUNT
R884
220k
NO MOUNT
SECTION 1
SERVICING NOTES
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
1. Turn ON the [OPERATE] button and press [CD] button to CD
position.
2. Open the CD lid.
3. Turn on SW2 with screwdriver, etc. as following figure.
4. Press the N X (CD) button.
5. Confirm the laser diode emission while observing the objecting
3. Turn on SW2 with screwdriver, etc. as following figure.
4. Press the N X (CD) button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
SW2
NOTE FOR REPLACEMENT OF THE IC804 AND
IC806
IC806
There have been changes to the 3.3V regulator circuit in the course
of production.
When repairing the 3.3V regulator circuit, check which of TYPE A
or B is applicable as specified in the table below.
of production.
When repairing the 3.3V regulator circuit, check which of TYPE A
or B is applicable as specified in the table below.
Ver. 1.4
