Sony CFD-E90L Service Manual ▷ View online
5
CFD-E90L
8
GB
Playing a tape
Connect the supplied mains lead.
1
Press xZ to open the tape
compartment and insert a recorded
tape. Use TYPE I (normal) tape only.
Close the compartment.
2
Press n.
The player turns on (direct power-on)
The player turns on (direct power-on)
and starts playing.
With the side you want
to play facing you
Display
2
1
Basic Operations
9
GB
Use these buttons for additional operations
To
Press
adjust the volume
VOLUME +*, —
(VOL +, — on the remote)
(VOL +, — on the remote)
stop playback
xZ
fast-forward or rewind the tape
m
or M
pause playback
X
Press the button again to
resume play after pause.
resume play after pause.
eject the cassette
xZ
turn on/off the player
OPERATE (or POWER)
* VOLUME + and n have a tactile dot.
xZ
X
m, M
OPERATE
(or POWER)
VOLUME +, –
10
GB
Recording on a tape
Connect the supplied mains lead.
1
Press xZ to open the tape
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
2
Select the programme source you
want to record.
To record from the CD player, insert
To record from the CD player, insert
a CD and press x on the CD section.
To record from the radio, tune in the
station you want.
3
With the side you want to
record on facing you
Display
1
Basic Operations
11
GB
3
Press z to start recording
(n is depressed automatically).
Use these buttons for additional operations
Tips
¥ Adjusting the volume or the
¥ Adjusting the volume or the
audio emphasis will not
affect the recording level.
¥ If the MW/LW programme
makes a whistling sound
after you’ve pressed z in
step 3, press MODE to select
select the position of ISS
(Interference Suppress
Switch) that decreases the
noise the most.
(Interference Suppress
Switch) that decreases the
noise the most.
¥ For the best results, use the
AC power as a power
source.
¥ To erase a recording,
proceed as follows:
1 Insert the tape whose
1 Insert the tape whose
recording you want to
erase.
2 Press FUNCTION on the
remote repeatedly until
TAPE appears.
3 Press z.
xZ
X
MODE
n
To
Press
stop recording
xZ
pause recording
X
Press the button again to resume
recording.
recording.
turn on/off the player
OPERATE (or POWER)
OPERATE
(or POWER)
6
CFD-E90L
The Timer
19
GB
Before you set the clock, connect the power
source.
1
Hold down CLOCK/SLEEP/TIMER
until CLOCK appears in the display.
The hour digit flashes.
until CLOCK appears in the display.
The hour digit flashes.
2
Turn the jog dial to set the current hour.
Then press ENTER.
The minute digits flash. Set the minutes
Then press ENTER.
The minute digits flash. Set the minutes
by turning the jog dial until the correct
minute is displayed.
The Timer
Setting the clock
— —:— — indication appears in the display
until you set the clock.
3
Press ENTER.
The clock starts from 00 seconds.
The clock starts from 00 seconds.
Tip
The time display system:
24-hour system
The time display system:
24-hour system
ENTER
Jog dial
CLOCK/SLEEP/TIMER
7
CFD-E90L
• This set can be disassembled in the order shown below.
SECTION 3
DISASSEMBLY
3-1.
DISASSEMBLY FLOW
Note:
Follow the disassembly procedure in the numerical order given.
3-2.
CABINET UPPER ASSY
SET
3-2. CABINET
UPPER ASSY
(page 7)
(page 7)
3-3. POWER
BOARD
(page 8)
(page 8)
3-4. TUNER
BOARD
(page 8)
(page 8)
3-6. CD MECHANISM DECK
(KSM-213RDP)
(page 9)
(page 9)
3-7. OPTICAL PICK-UP
(KSS-213R)
(page 10)
(page 10)
3-10. R/P HEAD
(HRP301)
(page 11)
(page 11)
3-11. MAIN BELT (B),
SUB BELT (B)
(page 12)
(page 12)
3-5. MAIN BOARD
(page 9)
3-8. CABINET
FRONT SECTION
(page 10)
(page 10)
3-9. TAPE MECHANISM DECK
(MF-E95)
(page 11)
(page 11)
3-13. D-OUT
ASSY
(page 13)
(page 13)
3-14. D-OUT
BOARD
(page 13)
(page 13)
3-12. CD LID
(page 12)
6
two screws
(2.6)
(2.6)
7
two screws
(2.6)
(2.6)
0
connector
(CN313)
(CN313)
9
connector
(CNP324)
(CNP324)
qa
connector
(CN311)
(CN311)
2
two screws
(2.6)
(2.6)
4
two screws (2.6)
5
screw (2.6)
qs
cabinet upper assy
1
Open the CD lid.
3
8
8
CFD-E90L
3-3.
POWER BOARD
3-4.
TUNER BOARD
5
screw
(2.6
(2.6
×
8)
4
3
screw (2.6
×
10)
2
three screws
(2.6
(2.6
×
8)
1
connector
(CNP1)
(CNP1)
7
TUNER board
6
tuner PC board holder
1
connector
(CNP901)
(CNP901)
3
2
two screws
(2.6
(2.6
×
10)
4
connector
(CNP322)
(CNP322)
5
POWER board
Click on the first or last page to see other CFD-E90L service manuals if exist.