Sony CFD-E77L Service Manual ▷ View online
5
CFD-E77L
8
GB
Playing a tape
Connect the supplied mains lead (see page 24).
1
Press xZ to open the tape
compartment and insert a recorded
tape. Use TYPE I (normal) tape only.
Close the compartment.
compartment and insert a recorded
tape. Use TYPE I (normal) tape only.
Close the compartment.
2
Press n.
The player turns on (direct power-on)
and starts playing.
and starts playing.
With the side you want
to play facing you
to play facing you
Display
2
1
Basic Operations
9
GB
Use these buttons for additional operations
To
Press
adjust the volume
VOLUME +, –
(VOL +, – on the remote)
(VOL +, – on the remote)
stop playback
xZ
fast-forward or rewind the tape
m or M
pause playback
X
Press the button again to
resume play after pause.
resume play after pause.
eject the cassette
xZ
turn on/off the player
OPERATE
xZ
X
m
,
M
OPERATE
VOLUME +, –
10
GB
Recording on a tape
Connect the supplied mains lead (see page 24).
1
Press xZ to open the tape
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
2
Select the programme source you
want to record.
want to record.
To record from the CD player, insert
a CD (see page 4) and press x on the
CD section.
a CD (see page 4) and press x on the
CD section.
To record from the radio, tune in the
station you want (see page 6).
station you want (see page 6).
3
With the side you want to
record on facing you
record on facing you
Display
1
RADIO
AUTO PRESET
BAND
Basic Operations
11
GB
3
Press z to start recording
(n is depressed automatically).
(n is depressed automatically).
Use these buttons for additional operations
Tips
• Adjusting the volume or the
audio emphasis (see page
18) will not affect the
recording level.
18) will not affect the
recording level.
• If the MW/LW
programme makes a
whistling sound after you've
pressed z in step 3, press
MODE to select the
position of ISS
(Interference Suppress
Switch) that most decreases
the noise.
whistling sound after you've
pressed z in step 3, press
MODE to select the
position of ISS
(Interference Suppress
Switch) that most decreases
the noise.
• For the best results, use the
AC power as a power
source.
source.
• To erase a recording,
proceed as follows:
1 Insert the tape whose
1 Insert the tape whose
recording you want to
erase.
erase.
2 Press X.
3 Press n.
4 Press z.
5 Press X.
3 Press n.
4 Press z.
5 Press X.
xZ
X
OPERATE
MODE
n
To
Press
stop recording
xZ
pause recording
X
Press the button again to resume
recording.
recording.
turn on/off the player
OPERATE
6
CFD-E77L
The Timer
19
GB
Before you set the clock, connect the power
source (see page 24).
source (see page 24).
1
Press MENU•ALARM until “CLOCK”
appears in the display, then press
DSPL•ENT MEM.
The hour digit flashes.
appears in the display, then press
DSPL•ENT MEM.
The hour digit flashes.
2
Turn the jog dial to set the current hour.
Then press DSPL•ENT MEM.
The minute digits flash. Set the minutes
by turning the jog dial until the correct
minute is displayed.
Then press DSPL•ENT MEM.
The minute digits flash. Set the minutes
by turning the jog dial until the correct
minute is displayed.
The Timer
Setting the clock
“– –:– –” indication appears in the display
until you set the clock.
until you set the clock.
DSPL
ENT MEM
ENT MEM
Jog dial
3
Press DSPL•ENT MEM.
The clock starts from 00 seconds.
The clock starts from 00 seconds.
Tip
The time display system: 24-hour system
MENU
ALARM
ALARM
7
CFD-E77L
• This set can be disassembled in the order shown below.
SECTION 3
DISASSEMBLY
3-1.
DISASSEMBLY FLOW
SET
3-2. CABINET
LOWER
LOWER
ASSY
(page 8)
3-3. AC INLET BOARD,
POWER BOARD
(page 8)
(page 8)
3-4. TUNER BOARD,
MAIN BOARD
(page 9)
(page 9)
3-6. CD MECHANISM DECK
(KSM-213CDP)
(page 10)
(page 10)
3-7. OPTICAL PICK-UP
(KSS-213C)
(page 10)
(page 10)
3-13. CONNECTOR SETTING
(page 13)
3-9. TAPE MECHANISM DECK
(MF-V5-117)
(page 11)
(page 11)
3-11. LID CASSETTE ASSY,
LCD BOARD
(page 12)
(page 12)
3-12. HEAD (HRP301),
MOTOR ASSY (M301),
BELT
(page 13)
BELT
(page 13)
3-5. COVER
PLATE ASSY
(page 9)
(page 9)
3-8. CABINET
FRONT ASSY
(page 11)
(page 11)
3-10. CD LID
(page 12)
8
CFD-E77L
3-3.
AC INLET BOARD, POWER BOARD
2
two screws
(BVTP3
(BVTP3
×
10)
3
AC INLET board
5
two screws
(BVTP3
(BVTP3
×
10)
6
plate shield (TRANS)
1
connector
(CN902)
(CN902)
4
connector
(CNP901)
(CNP901)
7
POWER board
Note:
Follow the disassembly procedure in the numerical order given.
3-2.
CABINET LOWER ASSY
1
two screws
(BVTP3
(BVTP3
×
14)
2
four screws
(BVTP3
(BVTP3
×
10)
3
5
4
two screws
(BVTP3
(BVTP3
×
14)
6
connector
(CN322)
(CN322)
7
connector
(CNP392)
(CNP392)
8
cabinet lower assy
4
screw
(BVTP3
(BVTP3
×
14)
Click on the first or last page to see other CFD-E77L service manuals if exist.