Sony CFD-E75 Service Manual ▷ View online
6
CFD-E75
8
Playing a tape
Connect the supplied AC power cord (see page 24).
1
Press xZ to open the tape
compartment and insert a recorded
tape. Use TYPE I (normal) tape only.
Close the compartment.
compartment and insert a recorded
tape. Use TYPE I (normal) tape only.
Close the compartment.
2
Press n.
The player turns on (direct power-on)
and starts playing.
and starts playing.
With the side you want
to play facing you
to play facing you
Display
2
1
Basic Operations
9
Use these buttons for additional operations
To
Press
adjust the volume
VOLUME +, —
(VOL +, — on the remote)
(VOL +, — on the remote)
stop playback
xZ
fast-forward or rewind the tape
m or M
pause playback
X
Press the button again to
resume play after pause.
resume play after pause.
eject the cassette
xZ
turn on/off the player
POWER
xZ
X
m
, M
POWER
VOLUME +, —
10
Recording on a tape
Connect the supplied AC power cord (see page 24).
1
Press xZ to open the tape
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
compartment and insert a blank tape.
Use TYPE I (normal) tape only.
2
Select the program source you want
to record.
to record.
To record from the CD player, insert
a CD (see page 4) and press x on the
CD section.
a CD (see page 4) and press x on the
CD section.
To record from the radio, tune in the
station you want (see page 6).
station you want (see page 6).
3
With the side you want to
record on facing you
record on facing you
Display
1
RADIO
AUTO PRESET
BAND
Basic Operations
11
3
Press z to start recording
(n is depressed automatically).
(n is depressed automatically).
Use these buttons for additional operations
Tips
¥ Adjusting the volume or the
audio emphasis (see page
18) will not affect the
recording level.
18) will not affect the
recording level.
¥ If the AM program makes a
whistling sound after you've
pressed z in step 3, press
MODE to select the
position of ISS
(Interference Suppress
Switch) that decreases the
noise the most.
pressed z in step 3, press
MODE to select the
position of ISS
(Interference Suppress
Switch) that decreases the
noise the most.
¥ For the best results, use the
AC power as a power
source.
source.
¥ To erase a recording,
proceed as follows:
1 Insert the tape whose
1 Insert the tape whose
recording you want to
erase.
erase.
2 Press X.
3 Press n.
4 Press z.
5 Press X.
3 Press n.
4 Press z.
5 Press X.
xZ
X
POWER
MODE
n
To
Press
stop recording
xZ
pause recording
X
Press the button again to resume
recording.
recording.
turn on/off the player
POWER
7
CFD-E75
The Timer
19
Before you set the clock, connect the power
source (see page 24).
source (see page 24).
1
Press MENU¥ALARM until CLOCK
appears in the display, then press
DSPL¥ENT MEM.
appears in the display, then press
DSPL¥ENT MEM.
The hour digit flashes.
2
Turn the jog dial to set the current hour.
Then press DSPL¥ENT MEM.
Then press DSPL¥ENT MEM.
The minute digits flash. Set the minutes
by turning the jog dial until the correct
minute is displayed.
by turning the jog dial until the correct
minute is displayed.
The Timer
Setting the clock
— —:— — indication appears in the display
until you set the clock.
DSPL
ENT MEM
ENT MEM
Jog dial
3
Press DSPL¥ENT MEM.
The clock starts from 00 seconds.
Tip
The time display system: 12-hour system
AM 12:00 = midnight
PM 12:00 = noon
AM 12:00 = midnight
PM 12:00 = noon
MENU
ALARM
ALARM
8
CFD-E75
• This set can be disassembled in the order shown below.
SECTION 3
DISASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
3-2.
CABINET LOWER ASSY
3-1.
DISASSEMBLY FLOW
Cabinet lower assy
Set
AC INLET board, POWER board
TUNER board, MAIN board
Cover plate assy
CD mechanism deck
(KSM-213CDP)
(KSM-213CDP)
Optical pick-up
(KSS-213C)
(KSS-213C)
Cabinet front assy
Tape mechanism deck
(MF-V5-117)
(MF-V5-117)
CD lid
Lid cassette assy,
LCD board
LCD board
Head (HRP301),
motor assy (M301), belt
motor assy (M301), belt
1
two screws
(BVTP3
(BVTP3
×
14)
2
four screws
(BVTP3
(BVTP3
×
10)
3
5
4
two screws
(BVTP3
(BVTP3
×
14)
6
connector
(CN322)
(CN322)
7
connector
(CNP392)
(CNP392)
8
cabinet lower assy
4
screw
(BVTP3
(BVTP3
×
14)
9
CFD-E75
3-3.
AC INLET BOARD, POWER BOARD
3-4.
TUNER BOARD, MAIN BOARD
2
two screws
(BVTP3
(BVTP3
×
10)
3
AC INLET board
5
two screws
(BVTP3
(BVTP3
×
10)
6
plate shield (TRANS)
1
connector
(CN902)
(CN902)
4
connector
(CNP901)
(CNP901)
7
POWER board
2
four screws
(BVTP3
(BVTP3
×
10)
qa
four screws
(BVTP3
(BVTP3
×
10)
4
two screws
(BVTP3
(BVTP3
×
10)
3
TUNER board
1
connector
(CNP1)
(CNP1)
6
connector
(CNP321)
(CNP321)
7
connector
(CNP802)
(CNP802)
8
FFC cable 27P
(CNP801)
(CNP801)
9
wire (flat type) (14 core)
(CNP323)
(CNP323)
0
FFC cable 13P
(CNP322)
(CNP322)
5
cover, speaker
qs
MAIN board
Click on the first or last page to see other CFD-E75 service manuals if exist.