Sony CDP-XE510 Service Manual ▷ View online
— 1 —
SPECIFICATIONS
Model Name Using Similar Mechanism
CDP-XE500
CD Mechanism Type
CDM14-5BD22
Base Unit Type
BU-5BD22
Optical Pick-up Type
KSS-213BA/F-NP
SERVICE MANUAL
AEP Model
UK Model
COMPACT DISC PLAYER
MICROFILM
CDP-XE510
Photo: BLACK
— 2 —
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
This caution label is located inside
the unit.
the unit.
The laser component in this product is ca-
pable of emitting radiation exceeding the
limit for Class 1.
pable of emitting radiation exceeding the
limit for Class 1.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
procedures other than those specified herein may result in
hazardous radiation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED LINE
WITH MARK
!
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
1. SERVICING NOTE
.......................................................... 3
2. GENERAL
.......................................................................... 4
3. DISASSEMBLY
3-1. Front Panel ........................................................................... 5
3-2. Base Unit (BU-5BD22) ......................................................... 5
3-2. Base Unit (BU-5BD22) ......................................................... 5
4. TEST MODE
....................................................................... 6
5. ELECTRICAL BLOCK CHECKING
.......................... 8
6. DIAGRAMS
6-1. IC Block Diagrams ............................................................. 10
6-2. Circuit Boards Location ...................................................... 13
6-3. Printed Wiring Board — BD Section — ............................. 15
6-4. Schematic Diagram — BD Section — ............................... 17
6-5. Printed Wiring Board — Main Section — .......................... 19
6-6. Schematic Diagram — Main Section — ............................ 21
6-7. Printed Wiring Board — Panel Section — ......................... 23
6-8. Schematic Diagram — Panel Section — ............................ 25
6-9. Printed Wiring Board — Loading, HP Section — .............. 27
6-10. Schematic Diagram — Loading, HP Section — .............. 28
6-11. IC Pin Functions ............................................................... 29
6-2. Circuit Boards Location ...................................................... 13
6-3. Printed Wiring Board — BD Section — ............................. 15
6-4. Schematic Diagram — BD Section — ............................... 17
6-5. Printed Wiring Board — Main Section — .......................... 19
6-6. Schematic Diagram — Main Section — ............................ 21
6-7. Printed Wiring Board — Panel Section — ......................... 23
6-8. Schematic Diagram — Panel Section — ............................ 25
6-9. Printed Wiring Board — Loading, HP Section — .............. 27
6-10. Schematic Diagram — Loading, HP Section — .............. 28
6-11. IC Pin Functions ............................................................... 29
7. EXPLODED VIEWS
7-1. Main Section ....................................................................... 33
7-2. Mechanism Deck Section (CDM14-5BD22) ...................... 34
7-3. Base Unit Section (BU-5BD22) .......................................... 35
7-2. Mechanism Deck Section (CDM14-5BD22) ...................... 34
7-3. Base Unit Section (BU-5BD22) .......................................... 35
8. ELECTRICAL PARTS LIST
........................................ 36
MODEL IDENTIFICATION
– BACK PANEL –
Parts No.
MODEL
AEP, EE, CIS
UK
PARTS No.
4-987-946-0
4-987-946-1
• Abbreviation
EE
: East European model
— 3 —
SECTION 1
SERVICING NOTE
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and turn
in the direction of arrow.
in the direction of arrow.
*
To close the disc table, turn the driver in the reverse direction.
Pull out disc table
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer
electrostatic breakdown because of the potential difference
generated by the charged electrostatic load, etc. on clothing and
the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
electrostatic breakdown because of the potential difference
generated by the charged electrostatic load, etc. on clothing and
the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveform is output two times.
check that the S curve waveform is output two times.
CD-TEXT TEST DISC
This unit is able to display the text data (character information)
written in the CD on its fluorescent indicator tube.
The CD-TEXT TEST DISC (TGCS-313: J-2501-126-A) is used
for checking the display.
To check, perform the following procedure.
written in the CD on its fluorescent indicator tube.
The CD-TEXT TEST DISC (TGCS-313: J-2501-126-A) is used
for checking the display.
To check, perform the following procedure.
Procedure:
1. Turn ON the power and set the test disc.
2. Press the
1. Turn ON the power and set the test disc.
2. Press the
” button and play back the disc.
3. The following will be displayed on the fluorescent indicator tube.
Display : 1kHz/0 dB/ L&R
4. Rotate the
≠ AMS ± knob to switch the track. The text
data of each track will be displayed.
Restrictions in CD-TEXT Contents and Display
The micro processor’s RAM has limit of capacity in this unit, The
display may not show all the track titles in a disc when you play the
CD TEXT TEST DISC, but it is not unusual. In that case, “NOT
DISPLAY” appears in the display.
The micro processor’s RAM has limit of capacity in this unit, The
display may not show all the track titles in a disc when you play the
CD TEXT TEST DISC, but it is not unusual. In that case, “NOT
DISPLAY” appears in the display.
— 4 —
SECTION 2
GENERAL
LOCATION OF PARTS AND CONTROLS
Front Panel
!¡ ≠ AMS* ± knob
!™ PHONES jack
!£ p (stop) button
!£ p (stop) button
!¢ P (pause) button
!∞ · (play) button
!§ Display window
!¶ MUSIC SCAN button
!• PEAK SEARCH button
!ª EDIT/TIME FADE button
!¶ MUSIC SCAN button
!• PEAK SEARCH button
!ª EDIT/TIME FADE button
* AMS is the abbreviation for Automatic Music Sensor.
1 POWER switch
2 PLAY MODE button
3 REPEAT button
4 TIME button
5 Disc tray
6 § OPEN/CLOSE button
2 PLAY MODE button
3 REPEAT button
4 TIME button
5 Disc tray
6 § OPEN/CLOSE button
7 0/) buttons
8 CHECK button
9 CLEAR button
!º ENTER button
9 CLEAR button
!º ENTER button
1
3
4
2
5
7
8 9 0
6
!¡
!™
!£
!¢
!∞
!§
!¶
!•
!ª