DOWNLOAD Sony CDP-XB930 / CDP-XB930E Service Manual ↓ Size: 4.6 MB | Pages: 44 in PDF or view online for FREE

Model
CDP-XB930 CDP-XB930E
Pages
44
Size
4.6 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
cdp-xb930-cdp-xb930e.pdf
Date

Sony CDP-XB930 / CDP-XB930E Service Manual ▷ View online

7
This section is extracted
from instruction manual.
8
SECTION  3
DISASSEMBLY
Note :
Follow the disassembly procedure in the numerical order given.
3-1. SLIDE RACK
3-2. FRONT PANEL
claws
claws
A
   
2
 Slide rack 
       (Disengage claws
       to remove the rack.)
1
 Eject CD by moving "A" in
     the direction of the arrow.
   
6
 Five screws
       (+BV 3 
×
 8)
7
 Front panel
    (Disengage claws to remove the rack.)
3
 Flat cable
2
 Connector
4
 Connector
5
 Four screws
    (+BV 3 
×
 8)
1
 Two connectors
claws
claws
9
When the p  button is pressed, the following will be displayed.
(partial lighting 2)
When the OPEN/CLOSE § button is pressed, all will light up
again.
• Key check
All buttons have corresponding button numbers. When a button
is pressed, the counter will count up and display the button’s
number. However, the counter will only count to “18”. It will
not count for buttons already pressed once, but will display the
button’s number.(Partial lighting 3)
SECTION 4
TEST MODE
4-1. AF MODE
The following checks can be performed in the AF mode, which is
set by connecting the TP51 (AFADJ) terminal on MAIN board to
the Ground and turning on the power.
• FL tube check
After all segments light up, when the · button is pressed, the
following will be displayed. (Partial lighting 1)
• Remote commander check
When the · button of the remote commander is pressed, the
following will be displayed. All go off when the other buttons
are pressed. (Partial lighting 4)
LANGUAGE
MUSIC SCAN
AUTO SPACE
PEAK SEARCH
PLAY MODE
REPEAT
FADER
TIME/TEXT
0
)
0
1
2
3
4
5
6
7
8
9
EDIT/
TIME FADE
CHECK
CLEAR
 P
ENTER
OPEN/CLOSE
   §
PLAY ·
STOP p
10
11
12
18
20
ALL lit
Partial lighting 1
Partial lighting 2
Button No.
Displayed
Button No.
Displayed
Button
2
4
6
8
10
12
14
16
18
20
(Partial lighting 2)
• Audio check
• Initial setting of digital filter and release of mute.
• When the TP51 (AFADJ) terminal on MAIN board is set to
HIGH (VDD), emphasis turns on. When set to LOW (Ground),
it turns off.
A B C D E F
 (Partial lighting 1)
88 TOTAL  88
Display of 
counting
Display of 
button number 
Â
Â
(Partial lighting 3)
(Partial lighting 4)
When you turn the AMS knob clockwise
JOG RIGHT
JOG LEFT
When you turn the AMS knob counter-clockwise
Button
10
Focus bias 8-step up (hexadecimal)
Middle of focus bias up/down turning point
Focus bias optimum point, jitter value
Tracking servo, sled servo off
Tracking gain up
Focus bias 8-step down (hexadecimal)
Immediate readjustment of focus bias
Focus bias 00 point
Tracking servo, sled servo on
Tracking gain down
1
2
3
4
5
6
7
8
9
10
4-2. ADJ MODE
The following operations are performed in the ADJ mode, which is
set by connecting the TP21 (ADJ) terminal to the Ground and turning
on the power.
• During playback, there is no problem even if the GFS is continu-
ously LOW.
• High speed search is prohibited during access.
• During playback, the gain of focus servo and spindle servo does
not decrease.
• Servo related manual operations and measurement can be per-
formed.
(For details of operations, refer to Table of Key Operations in
ADJ Mode.)
4-3. CLV-S MODE
The spindle servo for playback sets into the CLV-S mode when the
TP21 (ADJ) terminal is connected to Ground after turning on the
power.
TABLE OF BUTTON OPERATIONS IN ADJ MODE
The jitter value display mode can be set after the all-music remaining
number mode using the  TIME/TEXT  button.
The functions of the number buttons are shown in the following
table.
FUNCTIONS OF NUMBER BUTTONS
(With the attached remote commander)
Function
Button
R350
CN305
CN304
TP21
(ADJ)
TP51
(AF ADJ)
 
[MAIN BOARD] — (Component Side) —
4-4. AGING MODE
This unit is equipped with an aging mode to check operations of the
mechanism deck.
• When faults occur:
Aging stops, and the state when aging stopped is displayed on the
fluorescent display tube.
• When no fault has occurred:
Aging is continued repeatedly.
Aging method 1
(When using the aging mode remote controller (J-2501-123-A)):
1. Press the  U  button and turn ON the power.
2. Set the disc on the tray.
3. Press the  AGING START  button of the aging remote
controller.
4. Aging starts and the message shown in Fig. 1 is displayed on
the fluoresent display tube.
5. To end, press the  U  button.
Aging method 2 (When no aging mode remote controller):
1. Press the  U  button and turn ON the power.
2. Set the disc on the tray.
3. Press the  
§ OPEN/CLOSE  button,  p  button, and
MUSIC SCAN  button at the same time. (If these buttons are
not pressed at the same time, nothing performs.)
4. Aging starts and the message shown in Fig. 1 is displayed on
the fluoresent display tube.
5. To end, press the  U  button.
Display when
normal
State
0
1
2
3
4
5
6
Load in
Access to TOC
Access to last track
Playback of last track
(3 seconds)
Access to first track
Playback of first track
(3 seconds)
Load out
Code
No.
Display when
abnormal
AGING-0
AGING-1
AGING-2
Counter
display
AGING-4
Counter
display
AGING-6
ERROR-0
ERROR-1
ERROR-2
ERROR-3
ERROR-4
ERROR-5
ERROR-6
Fig.1 Message in Aging Mode
Page of 44
Display

Click on the first or last page to see other CDP-XB930 / CDP-XB930E service manuals if exist.